Question about 2001 Chevrolet Blazer

1 Answer

Can a crack in a plastic vapor recovery canister be repaired with J B Weld?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 283 Answers

Are you referring to the two part epoxy? I have used that to repair gas tanks of lawn mowers and it worked fine.
Just be sure that the repair area is very clean and you rough the area with course sand paper before applying the adhesive. I would not use the 5 minute or fast dry epoxy. You want the repair to dry and cure for at least 24 hours before use.
Thanks for using FixYa!! I provide my answer for free as a public service.
J

Posted on Mar 12, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

P0446 ford escort 98


This Pinpoint Test is intended to diagnose the following:
  • Canister vent (CV) solenoid (9F945) (electrical concern only)
  • Fuel filler cap (9030)
  • Fuel tank pressure (FTP) sensor (9C052)
  • EVAP canister tube (fuel tank to EVAP canister)(9A228)
  • Fuel canister purge outlet tube (EVAP canister to EVAP canister purge valve) (9D661)
  • EVAP return tube (EVAP canister purge valve to intake manifold) (9G271)
  • EVAP canister purge valve (9C915)
  • Vacuum source line (input port vacuum to intake manifold)
  • Harness circuits: CV, FLI, FTP, EVAP Canister Purge Valve, SIG RTN, vehicle power (VPWR), reference voltage (VREF) and power ground (PWR GND)
  • Powertrain control module (PCM) (12A650)
This Pinpoint Test is used as an assistance in diagnosing the following EVAP components:
  • EVAP canister and bracket assembly (9E857)
    • EVAP canister sleeve assembly (fitting)(9D925)
    • Canister vent (CV) solenoid - hose assembly (9F976 or 9K318)
    • EVAP canister (9D653)
    • Canister vent (CV) solenoid (9F945)(mechanical concern only)
  • Fill limit valve assembly (9A086)
  • Fuel filler pipe flapper valve (9B085)
  • Fuel filler pipe check valve (9189), assembly (9285)
  • Fuel tank filler pipe (9034)
  • Fuel tank assembly (with fuel vapor vent valve) (9K007)
  • Fuel tank assembly (without fuel vapor vent valve) (9002)
  • Fuel vapor control valve (9B190)
  • Fuel vapor vent valve (9B593)
  • Liquid/vapor fuel discriminator (9G332)
  • On-board refueling vapor recovery (ORVR) T - connector assembly (9S314)
Description For additional information on the Evaporative Emission (EVAP) System, refer to Section 1A .
For additional information on the Evaporative Emission System Monitor, refer to Section 1A .
Pinpoint Test Schematics Escort/Tracer (2V)
aa3060b.gif

May 28, 2011 | 1998 Ford Escort

1 Answer

There is gasoline leaking out of a plastic unit located above spare tire at the rear of the vehicle


Hi, that is probably your EVAP system vapor canister. The charcoal canister stores fuel vapors that are later fed into the engine for burning. If it's leaking, you probably need a new one. Check to make sure it's installed properly and not leaking from the hoses. If the housing is cracked or has a hole in it, get a new canister or see if it can be repaired. Unless there is a lot of fuel leaking, it is probably safe to drive the truck--just keep it on the asphalt--no offroad until the repair is made. Please let me know if you have more questions, and thanks for using FixYa.

May 06, 2011 | 2000 GMC Jimmy

2 Answers

Check engine lite came on code is p1443 what does this code mean


P1443 Evaporative Emission Control System Control Valve The Evaporative Emission Control System monitors the fuel vapor flow between the engine intake manifold and the EVAP canister. The system failure occurs when a leak or blockage between the intake manifold, the EVAP canister purge valve and the EVAP canister is detected by the PCM.

Code P1443 Possible Causes:

- Pinched, blocked or plugged fuel vapor tubes/hoses (except between fuel tank and EVAP canister)

- Damaged EVAP canister

- Disconnected, cracked or cut fuel vapor tubes/hoses (except between fuel tank and EVAP canister)

- Damaged EVAP canister purge valve

May 04, 2011 | 1997 Ford Escort

1 Answer

Where is the fuel vapor canister located on a 2000 silverado


The vapor canister is located under the vehicle near the fuel tank.
It is made out of black plastic and has plastic lines running to it.

Nov 03, 2010 | 2000 Chevrolet Silverado

1 Answer

Obd-2 code p1455


DTC P1455 - Substantial Leak or Blockage in Evaporative Emission Control System

The PCM monitors the complete EVAP control system for no purge flow, the presence of a large fuel vapor leak or multiple small fuel vapor leaks. The system failure occurs when no purge flow (attributed to fuel vapor blockages or restrictions), a large fuel vapor leak or multiple fuel vapor leaks are detected by the EVAP running loss monitor test with the engine running (but not at idle).

Check this possible causes:
After-market EVAP hardware (such as fuel filler cap) non-conforming to required specifications
Disconnected or cracked fuel EVAP canister tube, EVAP canister purge outlet tube or EVAP return tube
EVAP canister purge valve stuck closed
Damaged EVAP canister
Damaged or missing fuel filler cap
Insufficient fuel filler cap installation
Loose fuel vapor hose/tube connections to EVAP system components
Blockages or restrictions in fuel vapor hoses/tubes (items also listed under disconnections or cracks)
Fuel vapor control valve tube assembly or fuel vapor vent valve assembly blocked
Canister vent (CV) solenoid stuck open
Mechanically inoperative fuel tank pressure (FTP) sensor


Check for audible vacuum noise or significant fuel odor in the engine compartment or near the EVAP canister and fuel tank

Tell us news.

Jul 19, 2010 | 1996 Ford Explorer

2 Answers

P0455 evap emission control system leak (large) on 2000 VW beetle


EVAP evaporative emissions systems monitoring
This system includes the on-board refueling vapor recovery (OVRV) system with leak detection (LDP) pump.

The ORVR system filters fuel vapor through the EVAP canister to prevent vapor escaping directly into the atmosphere.

The engine Control Module (ECM) determines when appropriate conditions are met and activates the LDP to pump a small amount of air pressure into the fuel tank and lines. The pump runs until a pre-determined pressure or time is reached. If the system does not hold the pressure, a fault or DTC is stored in the ECM.

The area this is located is behind the right plastic rear wheel liner cover. You will see the fuel filler neck from there and the rest of the EVAP system. Visual check for cracks on all the hoses specially the hose clamps. There are 3 lines connected to the Activated charcoal canister (EVAP canister fastened to body) that are detachable and use O-rings for secured sealing. Check if O-rings, if damaged, replace.

Apr 18, 2010 | 2000 Volkswagen Beetle

1 Answer

2000 ford taurus gas tank has what appears to be a fitting on the top right rear that has hoses attached. there are stains and gas smell coming from this area. my repair manual mentions a plastic push...


The Evaporative Emission Control System monitors the fuel vapor flow between the engine intake manifold and the EVAP canister. The system failure occurs when a leak or blockage between the intake manifold, the EVAP canister purge valve and the EVAP canister is detected by the PCM.

Code P1443 Possible Causes:

- Pinched, blocked or plugged fuel vapor tubes/hoses (except between fuel tank and EVAP canister)

- Damaged EVAP canister

- Disconnected, cracked or cut fuel vapor tubes/hoses (except between fuel tank and EVAP canister)

- Damaged EVAP canister purge valve

Notes: Check for audible vacuum noise in the engine compartment or significant fuel odor in the engine compartment or near the EVAP canister.

On my '98 4x4, the cannister purge valve is located under the hood, mounted on the driver's side fender.

The EVAP cannister itself is located underneath the truck, in back, between the spare tire and the truck bed (have to remove the spare to get at it).

If it were me I would hold off on replacing parts...I'd drive around some more first, making sure that I don't overfill the gas tank or run it dry and making sure I replace the gas cap properly, etc. If the code returns, then its time to think repairs.

Jul 02, 2009 | 2000 Ford Taurus

1 Answer

Check engine light is on for emission evaporator failure-large


P0455 - EVAP Control System Leak Detected (No Purge Flow or Large Leak) The PCM monitors the complete EVAP control system for no purge flow, the presence of a large fuel vapor leak or multiple small fuel vapor leaks. The system failure occurs when no purge flow (attributed to fuel vapor blockages or restrictions), a large fuel vapor leak or multiple fuel vapor leaks are detected by the EVAP running loss monitor test with the engine running (but not at idle).
  • After-market EVAP hardware (such as fuel filler cap) non-conforming to required specifications
  • Disconnected or cracked fuel EVAP canister tube, EVAP canister purge outlet tube or EVAP return tube
  • EVAP canister purge valve stuck closed
  • Damaged EVAP canister
  • Damaged or missing fuel filler cap
  • Insufficient fuel filler cap installation
  • Loose fuel vapor hose/tube connections to EVAP system components
  • Blockages or restrictions in fuel vapor hoses/tubes (items also listed under disconnections or cracks)
  • Fuel vapor control valve tube assembly or fuel vapor vent valve assembly blocked
  • Canister vent (CV) solenoid stuck open
  • Mechanically inoperative fuel tank pressure (FTP) sensor
Check for audible vacuum noise or significant fuel odor in the engine compartment or near the EVAP canister and fuel tank. ----------------------------------------------------------------------------- HX43 DTC P0457: CHECK FOR MISSING OR LEAKING FUEL FILLER CAP
  • Check for missing fuel filler cap.
  • Check for loose fuel filler cap.
  • Check for possible cross-thread fuel filler cap condition.
Is a fault present concerning the proper installation of the fuel filler cap? Yes No REPLACE cross-threaded or damaged fuel filler cap. RECONNECT and TIGHTEN the fuel filler cap only one eighth turn so that the cap initially clicks by sound or touch. CLEAR Continuous Memory DTCs. COMPLETE an Evaporative Emission Running Loss Monitor Repair Verification Drive Cycle (refer to Section 2 , Drive Cycles). RERUN Quick Test . If DTC P0455 or P0457 is present, Go to HX44 . CLEAR Continuous Memory DTCs. COMPLETE an Evaporative Emission Running Loss Monitor Repair Verification Drive Cycle (refer to Section 2 , Drive Cycles). RERUN Quick Test .

For DTC P0455 still present: Go to HX44 .

Otherwise, INFORM the vehicle owner that it is important and necessary to immediately install the fuel filler cap after every refueling event. HX44 DTC P0455: VISUAL INSPECTION FOR SUBSTANTIAL EVAPORATIVE EMISSION SYSTEM LEAKS
  • Check for missing fuel filler cap. If the cap is loose DO NOT DISTURB EVAP system.
  • Verify that both the input port vacuum hose and EVAP return tube are attached to the EVAP canister purge valve. Note: If the EVAP canister-CV solenoid assembly is not accessible during this pinpoint test step, GO to Evaporative Emissions, Section 303-13 in the Workshop Manual for removal and installation instructions.
  • Verify that the CV solenoid is properly seated on the EVAP canister (if possible).
  • Visually inspect for disconnected or cracked fuel vapor hoses/tubes between the intake manifold, the EVAP canister purge valve, the EVAP canister, the fuel vapor vent valve assembly and if applicable the fuel vapor control valve tube assembly.
  • Check for damage to the fuel filler pipe and the fuel tank.
Is a fault indicated? Yes No CONNECT or REPLACE fuel vapor hoses/tubes as required. REPLACE damaged EVAP system components (fuel filler pipe, fuel vapor vent valve assembly, fuel vapor control valve tube assembly, EVAP canister purge valve, FTP sensor and EVAP canister-CV solenoid assembly) as necessary. REFER to Evaporative Emissions, Section 303-13 in the Workshop Manual for removal and installation instructions. GO to HX45 . GO to HX45 . HX45 DTC P1443 and P0455: CHECK FOR EVAPORATIVE EMISSION SYSTEM LEAKS
    Note: When checking for leaks or blockages in the EVAP system, energize (close) the canister vent (CV) solenoid through the scan tool for a maximum of nine minutes per pinpoint test step. Then de-energize the CV solenoid prior to performing the subsequent pinpoint test step. This is done to assure proper closing of the solenoid.
  • Disconnect and plug the EVAP return tube (EVAP canister purge valve to intake manifold) at the intake manifold vacuum source.
  • Connect scan tool.
  • Key on, engine off.
  • Access VPWR PID. If the voltage is not 12 volts or greater, GO to HX61 .
  • Locate evaporative test port [marked EVAPORATIVE SERVICE PORT DO NOT USE UNREGULATED PRESSURE ABOVE 6.89 kPa (1 PSI)] near EVAP canister purge valve or EVAP canister.
  • If vehicle is not equipped with the evaporative test port, GO to HX50 .
  • Install the Rotunda Evaporative Emission System Leak Tester 310-F007 (134-00056) or equivalent at the evaporative test port.
  • Close CV solenoid by accessing Output Test Mode on the scan tool.
  • Select ALL OFF mode and push START button.
  • Regulate the nitrogen or argon gas pressure on the tester to 3.48 kPa (14 in-H 2 O).
  • Follow the instructions that come with the EVAP System Leak Tester and pressurize the EVAP system.
  • Perform the EVAP system leak test.
Does the pressure on the EVAP system stay above 1.99 kPa (8 in-H 2 O) and pass the leak test? Yes No GO to HX46 . REMOVE the EVAP System Leak Tester from the evaporative test port and REINSTALL the test port cap. GO to HX50 .

Apr 15, 2009 | 1999 Lincoln Town Car

1 Answer

2006 jeep liberty will not take gas keeps clicking off gas pump. 3rd time at dealer. dealer has no idea what's wrong


The ORVR (On-Board Refueling Vapor Recovery) system consists of a unique fuel tank, flow management valve, fluid control valve, one-way check valve and vapor canister.

The ORVR (On-Board Refueling Vapor Recovery) system is used to remove excess fuel tank vapors. This is done while the vehicle is being refueled..

Fuel flowing into the fuel filler tube (approx. 1 inches I.D.) creates an aspiration effect drawing air into the fuel fill tube. During refueling, the fuel tank is vented to the EVAP canister to capture escaping vapors. With air flowing into the filler tube, there are no fuel vapors escaping to the atmosphere. Once the refueling vapors are captured by the EVAP canister, the vehicle's computer controlled purge system draws vapor out of the canister for the engine to burn. The vapor flow is metered by the purge solenoid so that there is no, or minimal impact on driveability or tailpipe emissions.

As fuel starts to flow through the fuel fill tube, it opens the normally closed check valve and enters the fuel tank. Vapor or air is expelled from the tank through the control valve and on to the vapor canister. Vapor is absorbed in the EVAP canister until vapor flow in the lines stops. This stoppage occurs following fuel shut-off, or by having the fuel level in the tank rise high enough to close the control valve. This control valve contains a float that rises to seal the large diameter vent path to the EVAP canister. At this point in the refueling process, fuel tank pressure increases, the check valve closes (preventing liquid fuel from spiting back at the operator), and fuel then rises up the fuel filler tube to shut off the dispensing nozzle.

Dec 22, 2008 | 2006 Jeep Liberty

Not finding what you are looking for?
2001 Chevrolet Blazer Logo

Related Topics:

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...