Question about 1993 Mazda RX-7

1 Answer

I put water in the rad after 4 liters it comes out the gearbox about 5in behind engine

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,536 Answers

One or more of the freeze plugs in the back of the block is leaking. You'll probably need to remove the clutch or torque converter and flywheel to replace it.

Posted on Mar 12, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have just picked up my kia Sedona from the Garage after having a refurbuished engine put in due to a blown Head gasket. Ran it on the motor way and the temperature gauge shot up to "H". I...


in my experience i would have just changed the head gasket instead of putting in a new motor

anyway there could be an air pocket in the engine or rad what i would do is

1 drain the rad by drain plug located at the bottom of rad on left or right side looks like a valve
2 start the car and slowly add 50/50 antifreeze to the rad
3 once rad is full open and fill coolant bottle
4 watch temp to see if it goes up to the high mark

if this does not help I recommend taken the car back to the place you took it to get fixed could be a head gasket problem

Sep 03, 2011 | Kia Sedona Cars & Trucks

1 Answer

How much tranmission fluid needed for nissan 2003 altima


in the manual it will tell you in specs but you can put in and run car till it gets warm and check level while adding make sure rad fan comes on that is hot enough with engine running and in park check level if empty should go from 4to 7 and if only changed filter in pan 3to 4 liters

Jan 13, 2011 | 2003 Nissan Altima

1 Answer

1996 Legacy Overheating It has coolant and both fans are working. Overheats after about 10 min of driving. Checked oil was a little low put 1 liter in. Radiator has pressure, opened when hot and coolant...


Costs nothing to try this, just in case coolant level was low when or after bottle changed, and you got an airlock. Start car when cold, rad cap off and heater on. Now let in run until it comes up to normal operating temperatures and rad fan(s) kick on and off, 2 or 3 times, and add coolant to proper level in rad if it goes down during process. Then after that, put rad cap back on, fill coolant return bottle to proper level and try it. Quite often when re-filling an engine cooling system, people forget to turn on heater to get coolant circulating through the heater core.

Nov 06, 2010 | 1996 Subaru Legacy

1 Answer

Cooling system flush


open nut at bottom of rad .let out all water ,then open cap for water in engine ,put water hose in cap in engine turn on water flush all rad out,,water will come out under rad ,,,put back on rad nut ......job done

Jun 18, 2010 | 1997 Cadillac DeVille

3 Answers

My 1998 buick century is leaking coolant from the engine where the water pump is mounted.


it could be a loos hose clip or the water pump, there is a gasket behind the water pump this could be leaking as well there is a quick fix you could try if its a clip or gasket leaking it should stop the leak,but it wont stop a water pump leaking ,,,,,,,,,,,
get some "rad seal" and tip it into the rad,,,not the header tank it go's right into the rad then top it up with water and run up the engine itll its hot after a short time the leak should stop,,fords put it in all there new cars and vans that come out there fatctorise,, so if its good for them to use it,, it must work?

Mar 09, 2010 | 1998 Buick Century

1 Answer

I have replaced the rad cap, water pump, thermostat and water pump heater on my 2000 Chevy Venture. The rad and heater core are good. The water pump heater was in for 2 days working great and now I'm...


first of all the water pump doesn't have a heater, all the water pump does is cycle water (coolant) throughout the cooling system, the heater is up inside the dash behind the glove box.

I would feel the two 3/4" heater hoses that run from the engine into the heater core, if both of them are hot (providing the engine is at full temp) it one is hot and the other is cold maybe the heater core is plugged.

Jan 10, 2010 | 2000 Chevrolet Venture

2 Answers

My dodge ram 1500 is overheating and burning the coolant. I already changed my radiator and the thermostat, and it's not leaking but I can smell like burnt coolant, I have to be putting more cooling every...


I would defiantly check the water pump, can you feel pressure in the rad lines? when you changed the rad and thermostat out, did you run your vehicle without the rad cap for awhile to ensure that there was no air locks within the system?
Water pump is located at the front of the engine behind the fan.
Good Luck! hope this helps.

Sep 05, 2009 | 2004 Dodge Ram 1500

1 Answer

Leaking water from top of water tank


rad caps are common for trouble, bottom of rads leak and a pipe that clicks into the rad leaks.
there is a core plug at back of engine that leaks, gearbox and fly wheel has to come out.
why dont you add a dye so you can see where it has come out. have pressure tested it to 25 psi and left to see where leaking,

Aug 08, 2009 | 2000 BMW 3 Series

1 Answer

Water come out from Water line when Engine Shutdown.


Does it show signs of over heating at all? When cool, take off rad cap & check level in rad & top it up. If down a lot, start engine, turn on heat & let run until you hear rad fan come on & check temperature gauge to see if normal operating temperature. Let it come on a couple of times, and top up rad an inch or so from top, then put rad cap back on. Top up bottle to proper level & try it. If it spits back into return bottle, try replacing rad cap.

Jun 06, 2009 | 2003 Ford Taurus

2 Answers

THERMOSTAT REPLACEMENT


Follow the top rad hose to the engine, where it connects that's the thermostat housing.

Jun 01, 2009 | 1999 Pontiac Grand Prix

Not finding what you are looking for?
1993 Mazda RX-7 Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...