Question about 1995 Plymouth Grand Voyager

1 Answer

Brake bleeding sequence for plymouth voyager - 1995 Plymouth Grand Voyager

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 367 Answers

Start with the wheel closest to the master cylinder, and work your way to the farthest. Front left, front right, rear left, rear right.

Posted on Mar 12, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

We're is the bleeding screw on the master cylinder on a 1999 Plymouth Grand Voyager

The master cylinder doesn't have a bleeding screw. Bleeding screws are located on each front caliper and the rear drum brakes. You'll need an assistant to press the brake pedal down on signal as you open the bleed screw slightly and close it back before they allow the pedal to return to normal position each time, until you've purged it through with new clean fluid. Fill up the master cyclinder frequently as you do this to assure it doesn't run dry. (If it does the master cylinder may be toasted.) Remember bleeding these types of cars is different than many others as it has dual lines, one for each side of the car. the bleed order is: LR, RF, RR, LF to get all the air out of the lines properly. Brake should be replaced every two years in humid or wet climates as brake fluid is hygroscopic... attaches to water vapor and stays in the braking system.

May 29, 2015 | 1999 Plymouth Grand Voyager

1 Answer

How to bleed brakes 1999 Plymouth grand voyager

open bleeder nut have someone step on brake peddle, depress, then air and fluid comes out, keep pedel down, tighten nut. do it until only fluid comes out. 3 times should be enough. Make sure to put clean brake fluid back into brake master. Keep full if you suck in air you have to start all over.

Oct 09, 2014 | 1999 Plymouth Grand Voyager

1 Answer

Brake bleeding sequence

start at the longest line first. Have a friend pump the pedal and hold down while you open the bleed screw. close the screw and pump again open the bleed screw and repeat the operation until you get solid brake fluid. go to the next longest line and repeat the process until you get to the last line . keep an eye on the reservoir level at all times

Dec 30, 2013 | 2002 Chrysler Voyager

1 Answer

98 Plymouth voyager brake issues

You never replace only one caliper

You do both sides

Bleeders are mounted to top of caliper

Have a helper in drivers seat to slowly
press brake pedal as you open & close

Start at back & do all 4 corners

The master takes care of it's self

Feb 26, 2013 | 1998 Plymouth Voyager

1 Answer

Sequence for bleeding all 4 brakes

Right rear, left rear, right front, left front assuming this is left hand drive for U.S. market.

Good luck.

Sep 25, 2011 | 2000 Plymouth Grand Voyager

2 Answers

Can't find the brake shoe adjustment on my '99 plymouth voyager

there are 2 or 3 plugs a side on the vehicle. the adjusted can be seen through the top center one not ether of he side one(s). it is above the bolts that hold the hub to the axle, and just below the wheel cylinder fitting/bleed screw.

Apr 04, 2009 | 1999 Plymouth Grand Voyager

1 Answer

How to bleed brake lines,94 grand voyager

Make sure it is full of fluid, go to the farthest wheel have someone pump the brakes up as much as possible have the person continue to push on the pedal as you open the the bleed valve located on the back of the brake drum continue this proscees pumping and bleeding until you get a continuous flow of fluid coming out, move to the opposite side and do it again go to the next farthest and continue until you have bled all wheel cylinders and have all the air out be sure you keep the reservoir full during this procedure

Mar 19, 2009 | 1994 Plymouth Voyager

1 Answer


I am a hydraulic technician and I can tell you that air is a killer in the hydraulic system.

Start from the rear and work your way forward. I f you are using the two person method, make sure the second person keeps the master cylinder full. If the fluid level dropped anywhere in between pressing and releasing the have a lot of air in the system.

Make sure you are tightening the bleed valve when the brake pedal is full pressed.

Remeber...start from the rear brakes first, then do the front.

Mar 16, 2009 | 1996 Plymouth Voyager

1 Answer

Pressure on all wheels except left rear

Air in brake line, bleed the entire system again

Mar 15, 2009 | 1990 Plymouth Voyager

1 Answer


Try this unless you have done so....just about fool-proof!!!


Mar 15, 2009 | 1996 Plymouth Voyager

Not finding what you are looking for?
1995 Plymouth Grand Voyager Logo

264 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts


Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8567 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides