Question about Ford Fusion

Open Question

I also have a problem with my 06 Ford Fusion blower motor resistor. Would you please send me a diagram that shows were it is located. I know it is under the glove box but I don't know what I am looking for. Thank you. Jim Abare

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
motor1258
  • 6674 Answers

SOURCE: how to replace a blower motor resistor in a 2004 jeep liberty

I'm not 100% sure where it is, or possibly built right in to the dash control/fan switch, but I'd be tempted to stop & see the parts guy at the dealership, or another dealership, and ask if they have one, or a picture of one. Once you see it, you'll know where to look. Just a guess but quite often built right into switch on dash.

Posted on Nov 27, 2008

Ad
  • 7 Answers

SOURCE: how to replace blower motor resistor on 2000 grand caravan

there will be two 8mm screws holdin it in.. with two connectors into it

Posted on Jan 05, 2009

  • 4 Answers

SOURCE: 2002 Chevy Impala Blower resistor location

It is on the passenger side, you have to remove the black plastic kick plate, below the glove box, to expose it (held in place with 2 latches and 1 push pin). The resistor is in front of the blower motor ( sandwiched between the motor housing and the firewall) it is tricky to get to, i think when i changed mine i didnt replace all the screws as they were difficult to remove and even harder to replace. Good Luck, Mike

Posted on Apr 20, 2009

cj2176
  • 520 Answers

SOURCE: Where is the blower resistor on a 2001 Nissan Sentra?

Its actually not that bad to change. If you open the glove box and remove the screws then the screws along the bottom of the glove box at the bottom of the dash the box will slide out. Remember to disconnect the light if it has one. Now you will be able to see the underside of the dash. You can see a large black box that has wires and vacuum lines all over. You need to locate a small flat plate with two screws and a plug in the middle. Disconnect the plug and remove the screws. The resistor will come straight out. The back side will look like small coiled up springs of different sizes. Install in reverse.Hope this helps. Good luck. Please re-post with updates. Thanks cj2176.

Posted on Jul 13, 2009

  • 181 Answers

SOURCE: Location of Front Blower Resistor on 99 Suburban K1500

MAIN BLOWER , MOTOR RESISTOR IS THE PLUG RIGHT BY THE BLOWER MOTOR. IF LAYING ON YOUR BACK LOOK UP AT BLOWER MOTOR IT THE PLUG TOWARDS THE FRONT SET ABOUT ONE INCH AWAY. PULL TWO 9/32 BOLTS OUT IT WILL PULL DOWN. THANKS

Posted on Feb 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2007 HHR, my temp gauge stops working and the same time the a/c stops blowing cold air...I called myself checking fuses and a relay, can you help?


You mean the blower motor stops blowing air , the A/C compressor is still engaged ? The temp gauge shouldn't have anything to do with the blower motor .But stranger things have happened on these systems when they are controlled by a electronic module (BCM )
Circuit/System Description
The instrument panel cluster (IPC) displays the engine coolant temperature as determined by the engine control module (ECM). The ECM sends the temperature data via high speed GMLAN serial data to the body control module (BCM). The BCM then sends the information via low speed GMLAN to the IPC in order to display the engine temperature.
The BCM applies voltage to the blower motor through the HVAC relay. The resistors and the blower motor are in a series circuit. The following list represents the number of resistors in series with the blower motor per particular speed request:
• Low speed--4 resistors
• Medium 1 speed--3 resistors
• Medium 2 speed--2 resistors
When the operator requests High speed, the HVAC control assembly applies ground directly to the blower motor through the high blower motor control circuit.
Do you know anything about automotive serial data communications ? GMLAN Is general motors version of C.A.N controller area network .

How to Diagnose Controller Area Network CAN

Do you know anything about diagnosing automotive electronics ? Using a digital volt ohm meter ? Using wiring diagrams to pin point locations in a electrical circuit for testing ? Do you know what a factory componet location diagram is ? It takes more then looking at fuse's an relays , to see if current is flowing in a electrical circuit .

Electric Testing Techniques You Need to Know

ECM Inputs and Outputs Diagnosis

http://www.bbbind.com/free_tsb.html Free wiring diagrams ! Enter vehicle info. Year , make , model and engine size ! Under system click on HVAC , under subsystem HVAC Controls . Then click the search button , then click the first blue link . This is the blower motor control diagram . Do you know how to read a wiring diagram ?

Apr 30, 2017 | Cars & Trucks

2 Answers

Where is the resister located


on the firewall close to the blower motor usually

Feb 29, 2016 | 2010 Ford F-150

1 Answer

Blower motor resistor location


    How to replace a Blower Motor Resistor - YouTube

    ? 11:17
    https://www.youtube.com/watch?v=Q-i0tytSYIM
    Aug 24, 2014 - Uploaded by ChrisFix
    How to fix a fan that doesn't work on low. If your interior AC/ Heatfan is not working on low, or one of the fan ...

    How to replace blower motor resistor in Chevrolet Silverado ...

    ? 5:06
    https://www.youtube.com/watch?v=qxWM285eizw
    Jul 25, 2011 - Uploaded by Auto Parts Direct To You
    In this video we show you how to replace the blower motor resistor in a ..... on high, but the air is cold and ...


Jan 16, 2016 | Cars & Trucks

1 Answer

Blower motor resistor location 2006


Under the blower motor inside the car (this is on the passanger side below the dash, when you get under there you will see the part that will need replacing). There is one screw and a connector to remove then pop the new one in and your done.

Dec 27, 2013 | 2008 Ford Fusion

2 Answers

Where is the blower motor resistor located?06 Fusion heater motor will only run 4 and 5 settings.


Hello stevenmickel: My name is Roger and I will help you: THe resistor is located down by the blower motor just to the left of the motor. I will attach a diagram to help with finding it. Should You need further help please just ask. Please rate the answer. Thank You for using Fix Ya. Rogerrogerf1_2.jpg

Dec 18, 2010 | 2008 Ford Fusion

2 Answers

Ford fusion 2007, blown blower fuse, replaced fuse, works at highest speed only (highest of 4) the other three setings don't work.


hte blower resistor is shot, near the blower motor, have the blower motor checked my guess is that it requiring too much power to run, hence the blown fuse

May 06, 2010 | 2006 Ford Fusion

1 Answer

My Blower motor for my heater on a 99 ford escort is not working.Is it the motor or resister that is gone??the fuses look ok where is the resister located can you send a diagram


look in passenger foot well on blower case for 4 wire connector.



Behind right side of I/P, A/C-heater plenum


resister bad would still allow high speed. may be blower motor.

  • The blower motor does not operate/does not operate correctly
  • Open fuse.
  • Tripped circuit breaker.
  • Circuitry open/shorted.
  • Heater blower motor switch (18578).
  • Heater blower motor switch resistor (18591).
  • Blower motor relay.
  • Blower motor.




bfddb09.gif

Jan 16, 2010 | 1999 Ford Escort

3 Answers

Blower motor stopped working.


https://www.genuineservice.com/genuineservice/en/default?page=genuineService

Go to this site and you can get a copy of your owners manual. Just pic the owner's manual link in the left side task bar.
The relay is located in the interior fuse panel. It should show you a diagram of the fuse panel in the owners manual.

Mar 02, 2009 | 2003 Ford Taurus

3 Answers

I HAVE AN 06 H3 HUMMER the heater was blowing fine when I shut the car off ok, when I got back in and started it the heaters blower stopped. I have checked all fuses and relays and they are fine I even...


check the blower speed control, it most likely burned out, also jump battery power direct to the blower and see if it runs, if it does the speed control is defective, if it doesn't the blower motor is toast.

Jan 16, 2009 | 2008 Hummer H3

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

119 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...