Question about 2011 Buick Enclave

4 Answers

My 2010 Buick Enclave has no audio. No radio, no onstar, no turn signal clicks when turning. No sort of any audio.

Posted by on

  • mike_applege Mar 12, 2011

    Already checked the fuses. That is not the issue.

×

Ad

4 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

My 2008 Enclave has the same problem. The radio is on but no sound. Has anyone found an answer to this problem yet. It isn't a fuse problem.

Posted on Mar 19, 2011

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Buick Master
  • 8,531 Answers

Hi, all of the audio goes through the head unit of the stereo system. If the sound system turns on, the problem may be with the speaker wire connector or internal to the head unit. It's possible the connector has just come undone. To access the cable, pull the trim panel straight off the console to expose the screws. Remove the screws holding the unit in the dash. Carefully slide the unit out to access the cables. Check all connectors for complete connections. The connectors should snap into place. If the connectors are good, I recommend you get warrantly service to repair the head unit. Please let me know if you have questions and thanks for using FixYa.

Posted on Mar 12, 2011

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 59 Answers

Sounds like you blew a fuse. Could just be a fluke, replace the fuse, and if it blows again you will need to take it to the dealership to address the issue.

Good luck!

Posted on Mar 12, 2011

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

My 2010 buick enclave gets no am radio just static

Posted on Oct 30, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 Buick Enclave The sound comes on and off when it wants. The sound for music, blinkers and back up alarms do this, although the stereo looks like it working just fine. What's the problem?


Saying this or that is the problem won't work with your vehicle , an most all vehicle's . Given the amount of electronic's (computers C.A.N communication networks etc.. ) The BCM - body control module uses input's from ignition switch signals to determine what mode the vehicle is in . The BCM energizes relay's an sends messages on the serial data network to wake up other modules . The radio is also on the C.A.N network , signals from the BCM could be turning it on , as well as the turn signals , because the BCM functions the turn signals too .

The LT/TRN/SIG and RT/TRN/SIG fuses in the I/P fuse block supplies battery positive voltage to the body control module (BCM). When the turn signal switch is placed in either the left or right position, a signal is sent to the BCM to illuminate the desired turn signal lamps. The BCM has an internal flasher that sends an ON-OFF voltage signal to either the left or right turn signals and their instrument panel cluster (IPC) indicator. When the hazard switch is pressed, a separate ground signal is sent to the BCM to activate and flash all turn signal lamps including both IPC turn indicators. The front and rear turn signals are grounded at G401.
How to Diagnose Controller Area Network CAN

This is something best left to a qualified repair that has the proper tools to diagnose it .

Mar 03, 2017 | 2008 Buick Enclave

1 Answer

Where in the car is the onstar antenna 2010 Buick LaCrosse CXL


Onstar uses the same antenna as the GPS. Its that stubby thing on the roof.

Nov 12, 2015 | 2010 Buick LaCrosse CXL

1 Answer

Abs and stability lights are on,what does this mean 2010 buick enclave?


Its Time You Replace That old Piece Of Junk With A KIA Sedona With A 10 Year Warrenty!!!

Dec 08, 2014 | 2010 Buick Enclave CX

1 Answer

How do i change the brake light bulb on a 2010 buick enclave


Good Question, but there is more then one, which one are you talking about; right, left, CHMSL?

Nov 28, 2014 | 2010 Buick Enclave

1 Answer

Locating the fuse box on a 2010 buick enclave


You find here (website Autogenius.info - link below) - information about fuse box, location and description for Buick Enclave - 2010

http://www.autogenius.info/en/buick-enclave-2010-fuse-box-diagram

Feb 18, 2013 | 2009 Buick Enclave

1 Answer

Our 2010 Buick Enclave has all the audio muted. The radio, the turn signal sounds when they blink, the onstar system. All sounds are muted. What is causing this?


first check ur fuses if their is any bad ones replace them and check and see if everythings working.if not disconnect ur battery for about 15 min then reconnect and then check everthing

Mar 12, 2011 | Buick Enclave Cars & Trucks

2 Answers

How do i change the rear turn signal bulb on a 2009 buick enclave?


Read the owner manual. Note that 2008 & 2009 manuals have incorrect information. Locate 2010 Enclave on internet. It has correct description and bulb number. Bulb is a 7443, NOT a 3157.

Feb 09, 2011 | 2009 Buick Enclave

1 Answer

How do I disable auto answering on my Bluetooth for my 2009 Buick Enclave? I used to be able ito gnore incoming calls, now the Bluetooth automatically answers after 2 rings. Thanks


Have you looked in your phone menu for auto answer You may find it under tools. If you can't find it, get a hold of ONSTAR and ask them to set it back to normal.
http://www.onstar.com
Or best way is to call them from your car phone.

May 31, 2010 | 2009 Buick Enclave

Not finding what you are looking for?
2011 Buick Enclave Logo

Related Topics:

922 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...