Question about Dodge Ram 1500

2 Answers

No right low beam,bulb is good connector ok. - Ram 1500 Dodge Cars & Trucks

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,510 Answers

Check the fuse. The fuse must be in the main fuse box. The position and function of the fuses is normally marked on the inside of the fuse box cover and also in the owner's handbook. If you don't come right with these, work your way through the fuses looking for a blown one. To ease your search the light fuse it should be around 10 to 15 amps.

Posted on Mar 12, 2011

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 130 Answers

Check fuse box under hood it has fuses and relays for high and low beam lights

Posted on Mar 12, 2011

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

  • 104 Answers

SOURCE: Right headlamp doesn't work on low beam only

in this case make sure you have voltage going to the low beam lights. 12 volts. you need a volt meter. if you do not have volatge you have to check and make sure power is going through the fuse. a bad fuse will be broke, but you can have a good fuse with no power going through it. if you have power going through the fuse you have a wiring open somewhere between fuse and whatever is between the headlight connecter.

plz check and get back i will keep checking on here on and off.

Michael
ASE certified
PLZ rate

Posted on Feb 09, 2009

  • 290 Answers

SOURCE: no low beams bulbs are ok fuses look good

There may be a relay that operates the low beam lights, check the owners manual to see if there is a relay, you should be able to hear it go "click" if there is one.

Posted on Dec 26, 2009

  • 1 Answer

SOURCE: Audi A4 2002 Low beams & Right front turn signal stopped working

but on 2002 A4, F20 and F21 are empty! Does anyone has an idea where the headlight fuses located?

Posted on Jun 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What would cause the low beam headlight not to work when all other lights work?


If you have standard halogen bulbs:

  1. Burned out light bulb; or
  2. Fried wires between the dashboard wiring harness and the headlight bulb connectors; or
  3. Fried headlight bulb connectors.
If you have HEI emitters:
  • Failed ballast.

May 11, 2015 | 2002 Mercury Grand Marquis

4 Answers

I have a 2006 civic SI. DRL indicator is on, driver side low and high beam ok. Passenger side low beam ok but DRL and hi beam not working. Any help is appreciated.


When either the high or low beam light is out in either side, DRL (daytime running lights) indicator will come on. When one bulb goes out, that's a clue the opposite bulb will burn out soon, so its best to replace both bulbs. If it was a fuse issue, both left and right side would be out. If driver side is OK but passenger side is not, then its a bulb issue. A 2006 Honda civic takes 9006 (HB4) low beam bulbs and 9005 (HB3) high beam bulbs. Cheapest is online from Walmart site-2-store. After procuring, wear latex, vinyl, or ANY gloves to keep your (corrosive) oil skin from coming in contact with headlight glass bulbs. Your skin oil will chemically react and cause shorter life span on glass bulbs. Instruction don't tell you this, so you handle with your hands, then need to replace bulbs 3 years later instead of 5 years (or more) in the future. With gloves on, pop the hood and look behind each headlight. Turn counter clockwise to unlock headlight bulb holders. Its a quarter to half turn to unlock bulb holder lock. Replace one bulb at a time so you don't confuse high beam from low beam. The wire has a tab you need to lift to pull out & disconnect wire connector. You might need a slim narrow-**** (NOT phillips) screwdriver to lift the tab; or use your house key. Snap the wire connector to the new bulb, then twist into headlight housing to secure bulb holders, then move on to the next bulb to repeat the procedure. Pict below, 9005 high beam is on the left, 9006 low beam is on the right. Handle by grasping the plastic base, not the glass bulbs. The raised potrusion on the bottom center is where the tab locks onto wire connector. Replace all 4 bulbs now, but in the future, its likely the low beam will wear out before the high beam. In the future, replace only the pair, not all 4. The factory installs inferior bulbs that go out sooner, hoping you'll take to dealership and they ******** you with higher parts-n-labor fees. As opposed to Walmart online site-2-store, it would cost you AT LEAST triple in parts & labor from dealership to replace all 4 headlight bulbs :-(
45d1f6ac-2983-42b9-a46c-30ef441b89e7.jpg

Nov 29, 2013 | 2006 Honda Civic

1 Answer

Low beam light problem no low beam on driver's side..bulb is good, switch is good and relay is good..


Check either the ground circiut or the plug connector at the lamp...Make sure lamp is getting 12 volts at the bulb connector and also a ground at the connector

Oct 03, 2009 | 2003 Acura 3.2TL

1 Answer

Headlight low beam


Test to see if you have voltage at the bulb connector in low beam position. I'd almost bet that if there is no voltage there for the low beams that you have a bad high/low switch.

Oct 03, 2009 | 2002 Subaru Forester

2 Answers

Dim headlight don't work but bright does and bulbs are ok


Several things on your cavalier could cause this to happen...
If it's just your high-beams, low-beams, or DRL that are out (just one), start with the DRL relay (in the fuse box). If that's not it, and it's not the DRL, try the multi-function switch (the thing attached to the left of your steering wheel, the headlight switch/cruise control switch). If all that checks out ok the next place to look under the hood... there is a pin-out connector/harness under the battery box (located in the front on the driver's side) that may be corroded. It is attached to the underside, and not easy to see without a mirror. If there is corrosion on the battery box, this connector is probably corroded as well...anything that runs off the battery will find it's way to this connector.

Note for anyone else that reads this: Different people will experience similar problems, sometimes with the low-beams, sometimes with the highs, because of different corrosion patterns and the DRLs being run from different bulbs.
Good luck...i hope this helps, please take time to rate me a fixya.

Jul 22, 2009 | 1992 Chevrolet Cavalier

2 Answers

Low beams do not work, replaced turn signal switch but still no low beams. High beams work but no low. Please Help


its probally the bulb........alot of car headlights are DUAL element meaning one bulb has 2 little elements inside one for low beam one for high beam...............Most times the low beam burns out because its used more.....get it one bulb gives both high and low beams.......REPLACE bulb......if you don't know what kind go to auto part store, tell them the make of your car and they will give you the right one .....

May 09, 2009 | 1997 Ford Explorer AWD

1 Answer

2002 saturn sc1 4door headlight problem


THE LOW BEAM HALF OF THE BULB HAS BURNED OUT AND NEEDS TO BE REPLACED. HOPE THIS HELPS. LET ME KNOW PLEASE. THANKS FOR USING FIX-YA.

May 04, 2009 | 2002 Saturn SC

1 Answer

Right Low Beam on/off intermittently.More off than on. Bulb OK, Fuse OK, all exposed wiring OK. If relay, where is relay located??


I would check the terminals of the connector. Most have a water resistant grease that also protects from corrosion. See if there is any in connector. I would then proceed to checking the gorund because the majority of the time with electrical problems it is a faulty ground connectoin.I do not see any relay in the schematic in my book. Hope this has helped. Good Luck

Jul 28, 2008 | 1997 Ford Explorer AWD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...