Question about 1995 Plymouth Voyager

1 Answer

Stays in low gear to long befof going into high gear, how do i adjust high bands?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Plymouth Master
  • 22,156 Answers

Check for a vacumn pipe from gearbox to inlet manifold and if fitted check for deterioration

Posted on Mar 12, 2011

Testimonial: "thank you very helpful"

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cat dp100 lift truck slow going into gear after starting


Probably the most common cause is low transmission fluid level. Next might be low hydraulic pressure, or loose band adjustment. Let us know if this steers you in the right direction for a solution.

Oct 06, 2014 | Cars & Trucks

1 Answer

1981 chevy truck that will only go in reverse, other gears will move it, but very slowly and at very high RPMs. Could this be torque converter, drivebands in transmission, or something else?


Transmission slipping,this is not the torque convertor, you would not even have reverse, You can adjust the band, when you adjust the band in doing so it holds the transmission drum and there it transfers power,So the transmission band is worth your try, if it fails you need a transmission

Nov 26, 2012 | Cars & Trucks

1 Answer

95 dodge neon wont go into reverse


Reverse clutch pack problem .

Mar 11, 2017 | Cars & Trucks

1 Answer

I hae a 2000 dodge ram 4wd automatic and it wont shift just revs up real high


I have a 1999 Ram that does the same thing. according to my research try re-adjusting the transmission bands. Depending what gear the truck ramps in rpms depends on what band needs adjusted.....the first 2 gears can be adjusted outside the transmission but the third gear is internal....also new transmission fluid and filter is recommended....is this doesnt solve the problem could be a solenoid....or governer pressure but that should throw a engine code is there is improper pressure. Hope this help GL

Sep 13, 2010 | 1998 Dodge Ram 1500 4WD

1 Answer

1994 Jeep Grand Cherokee Laredo 4.0 auto. At start up the trans pump sounds like lack of fluid whine. Put into gear & it drives for few minutes then slips to the point of stopping, if left idling it...


Likely it's better to leave the bands alone. The servos have plenty of travel and unless it was "hammering" into gear (from excessive clearance there) likely adjusting them won't do much. Pan rail is stamped pretty deep...carb cleaner wont clean it up enough to read?
Replacing the filter may help if it's plugged up. If not, don't bother replacing it...problem is internal and filter won't change much of anything.
You can only partially replace the fluid because the converter has no drain. Therefore, use cheap oil and a container of lucas conditioner. If it helps, do the change again at 3,000 miles and use a higher quality fluid along with another lucas.
If you can't get the unit #, buy both filter kits and make note of which is for what transmission. Return the unused one.

May 28, 2010 | 1994 Jeep Grand Cherokee

1 Answer

Transmission slipping


You have a problem with the bands in the transmission. They will need to be adjusted to correct the problem. Also have the transmission filter changed with new transmission fluid. Check the fluid level in transmission first,if low add fluid and test drive. If its the same as before you will need to go to a transmission place to have the bands adjusted to correct the problem. Hope this will help you.

May 23, 2010 | 1993 Dodge Dynasty

1 Answer

My tranmission was slipping and didnt go reverse so i changed my oil and filter now gears are passing but it still isnt going in reverse what could the problem be?


Low / Reverse band is likely fried. Remove the pan and valve body, check band adjustment per service manual. Or just pull the trans and rebuild it.

Jun 27, 2009 | 1996 Dodge Ram

2 Answers

1998 subaru band adjustment for auto transmission.


It is on the left side hard to spot. Look below the heater hoses. Good luck, take your time and have a great day.

Jun 26, 2009 | 1998 Subaru Legacy

1 Answer

Jeep grand cherokee revs for to high before changing gear


Message:
My 2002 Dakota has been somewhat confused about shifting as well. It showed a code P1762. I dropped the pan to install a new fluid filter and fluid-(use only ATF+3 or ATF+4). Since the pan was off I decided to adjust the bands. The front band controls the 2nd gear cluster. The rear band controls the 3rd gear cluster and reverse. For a 2-3 shift, the transmission shifts back to 1st gear with the front band while the rear band engages 3rd gear. If the front band does not release the 2nd gear clutches before the third gear clutches engage, the transmission binds, which shortens the life of the transmission clutches. If the front band releases too early in the shift, the engine will overspeed (sounds and feels like a slip) during the 2-3 shift.
The front band adjusting screw is on the driver's side above the shift linkage. The rear band is inside the fluid pan near the filter.
1. Loosen band adjusting screw locknut. Then back locknut off 3-5 turns. Be sure adjusting screw turns freely in case. Apply lubricant to screw
threads if necessary. The front band adjuster is on the outside of the transmission and the locknut requires a 3/4" wrench.

2. Using Inch Pound Torque Wrench C-3380-A, a 3-in. extension and appropriate Torx� socket (T-40), tighten adjusting screw to 72 in-lb. CAUTION: If Adapter C-3705 (from SPX Miller) is needed to reach the adjusting screw, tighten the screw to only 47-50 in. lbs. torque.

3. Back off adjusting screw the number of turns listed below for your transmission.

4. Hold adjusting screw in place and tighten lock-nut to:

41 N�m (30 ft. lbs.) for the front band
34 N�m (25 ft. lbs.) for the rear band
The adjustment screw inside the case is a square head bolt. You will need a 1/4 square head socket to fit your torque wrench.
Band adjustments for each model year:
1994

* Front Band - tighten to 72 in-lb, back off 2-1/2 turns (all transmissions)
* Rear Band
o 32/42RH - Tighten to 72 in-LB, back off 4 turns
o 36/37/46/47RH - Tighten to 72 in-lb, back off 2 turns

1995-1996

* Front Band
o 42RH - tighten to 72 in-lb, back off 2-1/4 turns
o 46RH - tighten to 72 in-lb, back off 2-7/8 turns
o 47RH - tighten to 72 in-lb, back off 1-7/8 turns
* Rear Band
o 42RE/RH - tighten to 72 in-lb, back off 4 turns
o 46RE/RH - tighten to 72 in-lb, back off 2 turns
o 47RE/RH - tighten to 72 in-lb, back off 3 turns

1997-1998

* Front Band
o 42RE - tighten to 72 in-lb, back off 3-5/8 turns
o 46RE - tighten to 72 in-lb, back off 2-7/8 turns
o 47RE - tighten to 72 in-lb, back off 1-7/8 turns
* Rear Band
o 42RE - tighten to 72 in-lb, back off 4 turns
o 46RE - tighten to 72 in-lb, back off 2 turns
o 47RE - tighten to 72 in-lb, back off 3 turns

1999

* Front Band
o 42RE - tighten to 72 in-lb, back off 3 turns. (TSB 21-16-98)
o 47RE - tighten band adj. screw to 72 inch pounds, back off 1 7/8 turns
* Rear Band
o 47RE - tighten band adj. screw to 72 inch pounds, back off 3 turns
+ The 47RH rear band requires a 1/4" hex driver, the front band requires a
T-30 Torx driver, the filter is held in place by two screws which require a T-20 Torx drive

2000-2002

* Front Band
o 42RE - Tighten band adj. screw to 72 in-lb, back off 3 turns
o 44RE - Tighten band adj. screw to 72 in-lb, back off 1 7/8 turns
o 46RE - Tighten band adj. screw to 72 in-lb, back off 2 7/8 turns
o 47RE - Tighten band adj. screw to 72 in-lb, back off 1 7/8 turns
From Bill Konolday's 47RE notes: I usually go a little looser than factory
specs on this front band - backing off the adjustment screw 2 or 2 1/4 turns.
Depending on the circumstances I have backed off the band up to 2 1/2 turns.
* Rear Band
o 42RE - tighten band adj. screw to 72 inch pounds, back off 4 turns
o 44RE - tighten band adj. screw to 72 inch pounds, back off 4 turns
o 46RE - tighten band adj. screw to 72 inch pounds, back off 2 turns
o 47RE - tighten band adj. screw to 72 inch pounds, back off 3 turns

2003

* Front Band
o 48RE - tighten band adj. screw to 72 inch pounds, back off 1-3/4 turns
* Rear Band
o 48RE - tighten band adj. screw to 72 inch pounds, back off 3 turns

2005

* Front Band
o 48RE - tighten band adj. screw to 72 inch pounds,
back off front band adjusting screw 1-3/4 turns for diesel vehicles,
or 1-1/2 turns, for V-10 vehicles.
* Rear Band
o 48RE - tighten band adj. screw to 72 inch pounds, back off 3 turns

94+ Automatic Transmission Bolt and Nut Torque Specs

* Front band adjustment locknut - 30 ft-lb
* Rear band adjustment locknut - 25 ft-lb
* Transmission pan bolts - 13 ft-lb
I just replaced the solenoid with the recommended transducer and all is fine now. The transducer cost me about $50 at a nearby dealership.
Hope this helps. -zman. rroszman@yahoo.com

Dec 09, 2008 | 2001 Jeep Grand Cherokee

Not finding what you are looking for?
1995 Plymouth Voyager Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...