Question about 1994 Jaguar XJ6

1 Answer

Ignition but no start - 1994 Jaguar XJ6

Posted by on

  • yadayada
    yadayada May 11, 2010

    Are there any trouble codes stored, have you done a quick test??

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have a 94 xj6 jag and after a blow out the car will not start. I pulled over and turned the car off. When I fixed the blowout it will not start. I have lights, power windows, sunroof, radio and dash lights but when I turn the key nothing. I cant even get it out of drive in first position. The guages doesn't function either, but the dash lights will. Can some one please help me!!!

Posted on Oct 25, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

It wont start with ignition but can clutch start and run fine what wrong with ignition


nothing wrong with the ignition but there is with the battery
when trying to start from the key , the battery falls below that required to start and run the ignition system but with a push start there is enough voltage to run the ignition system and then the alternator cuts in to supply power to all the rest
have a load test done on the battery

Mar 01, 2016 | 2000 Nissan Frontier

1 Answer

Do i need a fuse or immobilizer?


Search Results

    Replaced Ignition cylinder switch. Now I can't start car ...

    www.grandamgt.com > ... > Technical Q&A

    Aug 9, 2007 - 11 posts - ‎4 authors
    So the car should start right up right? Nope, still won't fire up, as if there is no fuel coming to engine. Did I do the passlock reboot procedure ...

    Auto Repair Problem with Car Won't Start and Ignition ...

    ? 1:20
    https://www.youtube.com/watch?v=Uz5dnWQBynw
    Aug 24, 2012 - Uploaded by YourMechanic
    When you start your car, it is the ignition switch that turns the engine on, when it is working properly ...

    Car won't start after changing ignition switch? ' Yahoo Answers

    https://answers.yahoo.com/question/index?qid...
    Jan 7, 2013 - Also, I think that you replaced the lock cylinder and not the ignitionswitch, .... Change ignition switch,but car won't start,acura integra 98 aut.

    HELP! Replaced ignition housing and barrel - car won't start ...


Feb 08, 2016 | Cars & Trucks

1 Answer

2001 dodge stratus no crank no start from ignition


When you use the ignition key you activate both the starter and ignition circuits. When you jump the starter motor all you do is crank the engine - you have not energized the ignition so car will not start.

Aug 26, 2015 | 2001 Dodge Stratus

1 Answer

My 97 geo prism starts when you put the car to ignite but after that it won't stay running what could it be


First turn of the key energize the car electrical circuits for some circuits radio ets. 2nd turn of the key energize the the starting cycle, when you turn the key to the third spring loaded start mode it completes the circuit to the starter solenoid which engages the starter and start the car, the spring in ignition return the key to ignition on.
Maybe you have a malfunction in the ignition on position. Dont have a large bunch of keys hanging in your ignition, it sings back and forth when the car is in the start mode and cause havoc to your ignition switch.

Jan 12, 2014 | Cars & Trucks

1 Answer

My Nissan maxima 09 won't start because it has this "yellow key" signal light turned on. It's a push to start and the key seems fine and working properly because I can lock and unlock ge doors, open the...


try another key key could be faulty or the ignition key immobilizer control module and ECM faulty.try this procedure remove all possible sources of signal interference from the key ring. switch ignition on for 5 seconds then switch off ignition. wait for 10 seconds switch ignition on 5 seconds again then switch ignition off. wait 10 minutes again then try start engine if engine dont start problem in the immobilizer control module,ignition key or ignition switch keylock cylinder,or ECM problem. have vechicle code scan first before buying new parts.

Nov 18, 2013 | Cars & Trucks

1 Answer

Engine wont start


Engine does not crank (Does not start)
1. Starter and starter relay
2. Neutral start switch circuit
No initial combustion (Does not start)
1. ECM power source circuit
2. Ignition coil (w/ Igniter) circuit
3. Fuel pump control circuit
4. Fuel Injectors.
No complete combustion (Does not start)
1. Fuel pump control circuit
2. Ignition coil (w/ Igniter) circuit
3. Fuel Injectors.

Jul 30, 2013 | Toyota Corolla Cars & Trucks

1 Answer

Is there a way to reset the ignition


use the ignition switch master key. turn the ignition switch for ten minutes until LED ignition warning light go off.then turn off ignition switch wait 5 seconds then try to start engine. if this procedure starts your engine have dealership or garage to check out theft security system.

Jul 28, 2013 | Cars & Trucks

1 Answer

Flashing alarm light after battery change. Car wont start,


System operation
System arms 5 seconds after switching ignition OFF. Switch ignition ON. Ensure clock LED illuminates for 3-5 seconds. If LED flashes rapidly at regular intervals for approximately 1 minute, then flashes at irregular intervals: Key code not recognised. Remove key and try again.
Programming
When
System malfunction: LED illuminates for 1 minute, then flashes at irregular intervals. Key(s) added or replaced.
NOTE: Replacement keys MUST have blue mark. Keys with red mark are NOT compatible with this system.
How
NOTE: Programming method using vehicle keys can be deactivated using diagnostic equipment.
Obtain 2 programmed keys (A and B). Insert key A into ignition switch. Turn ignition switch to position II. Wait 1 second. Switch ignition OFF. Remove key A. Insert key B into ignition switch within 5 seconds. Turn ignition switch to position II. Wait 1 second. Switch ignition OFF. Remove key B. Within 10 seconds: Insert key to be programmed into ignition switch. Turn ignition switch to position II. Wait 4 seconds. Switch ignition OFF. Wait 5 seconds. Start engine. If engine does not start and clock LED flashes: Switch ignition ON. Wait at least 20 seconds. Switch ignition OFF. Repeat programming procedure. Repeat above procedure to program remaining keys. Keys can also be programmed using diagnostic equipment

Mar 08, 2010 | 2000 Ford Focus

Not finding what you are looking for?
1994 Jaguar XJ6 Logo

Related Topics:

353 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Raygin
Raygin

Level 2 Expert

322 Answers

yadayada
yadayada

Level 3 Expert

61037 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...