Question about 1989 Ford Ranger

1 Answer

Can i put a 2.9 transmission in a 2.3 - 1989 Ford Ranger

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 63 Answers

I would say yes.but. the 2.9l that year were most all 4x4. if the trans you have from the 2.9 is a 4x4 trans then its going to have the wrong tail housing on it. but if its not a 4x4 then they should be the same transmission. but you will need to look and compare the two. i cant give a definite answer without seeing them but you shouldnt have a problem bolting it up.

Posted on Mar 12, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Shifter is in neutral. Why is manual transmission stuck in 3rd gear?


Internal transmission breakage has stuck the thing in 3rd gear. Stalls when putting in other gears because transmission is then being put into 2 gears at once. Better look into getting another transmission of having the current unit overhauled and repaired.

Oct 23, 2015 | 2002 Mazda Protege

1 Answer

How do i replace the transmission lines in a 1975 chevy pickup


You are going to see 2 lines on your transmission take them off and it is going to the radiater thake them of two and replace it refil your transmission o?l start your engine check for leaks put your transmission in drive wait for 5 seconds and put it back in park and check for o?l leak job done...

Jul 28, 2014 | Chevrolet 1500 Cars & Trucks

1 Answer

Transmission


check transmission fluid level could be low transmission is slipping.

Apr 11, 2013 | 2001 Chrysler Town & Country

1 Answer

How can I flush all the transmission fluid out of my transmission


in the transmission block u have 2 screws one in the top of it to put new fluid and one in the bottom to remove it so open the 2 to remove the fluid more quickly then close the one in the bottom and put new fluid.

May 05, 2012 | 1991 Ford F250

1 Answer

I WANT TO CHANGE MY TRANSMISSION FILTER ON MY 2003 CHEVY MALIBU. hOW MUCH FLUID WILL i NEED ?


  • When you change a transmission filter the general rule is you loos roughly 1/4 - 1/3 of your total transmission fluid capacity.
  • I would buy 3 quarts and dump two in the transmission after the filter/gasket change. Put your foot on the brake and go through the gears to fill the pockets in the transmission up. Then put then check the fluid and add some more as necessary. Should be around 2 1/2 quarts total you will loose in the filter change.

  • Hope this helps and thank you for using FixYa.

Regards, Tony

Jul 22, 2011 | 2003 Chevrolet Malibu

2 Answers

If someone put anitfreeze where the transmission fluid goes will i need 2 replace the whole engine?


No. your problem is in the transmission not your engine, flush transmission fluid and put new fluid is good idea to change the filter too. good luck.

Feb 19, 2011 | 2001 Hyundai Sonata

1 Answer

New refurbished transmission just put in now i have a code po732 gear 2 ratio already replaced the pules generators 2003 Hyundai Accent 1.6L.


CODE PO732 THAT IS GEAR 2 INCORRECT RATIO.FAULT IN TRANSMISSION RANGE SENSOR.PROBLEM IN SHIFT SOLENOID OR RELATED PRESSURE SWITCH.PROBLEM IN TRANSMISSION VALVE BODY.ALSO CHECK TO MAKE SURE TRANSMISSION FLUID LEVEL IS CORRECT.

Sep 24, 2010 | 2003 Hyundai Accent

1 Answer

Transmission light on, but no problems with the transmission, is the fluid low?


Hard to know. You fill it to the fill mark. If it is 2 quarts low, put 2 quarts in it. 1 pint, add 1 pint.

May 29, 2009 | 2002 Dodge Durango

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5530 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...