Question about 2000 Dodge Intrepid

1 Answer

How much does it cost to replace window blade holder for 2000 dodge intriped 2.7

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 367 Answers

If you mean the wiper ATM that the wiper blade attaches to, the arm itself hoes for $5-$20 at a junk yard, $30-$50 online and almost double that at a dealer. Installation prices will vary depending on the shops hourly rate.

Posted on Mar 12, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2000 dodge intriped .....when i put water in the radiator it runs out quick but the gage dont go to hot instead the oil light came on it over heated and shut down is it the hose or waterpump


All depends on where the leak is. Could also be a blown head gasket.
The temp gauge does not read because there is no liquid for it to measure.

Dec 11, 2012 | Cars & Trucks

1 Answer

The rear window wiper blade holder is rusted how do I remove it for replacement?


Three things you can replace depend on your budet
1) you can replace whole wiper blabe assembly by lift up the cover at the bottom end of the bale assembly and un-screw the nut and raplace whole assembly with arm , wiper insert etc ... with the new one This way cost you more.
2) on hte middle of the whole wiper blade assy has the flexible section, you can un-screw 2 small philipe pan head screw with screw driver and disconnect the top section with the wiper blade insert (rubber)
3) slide wiper blade insert out of the holder, becareful with 2 small steel blade will hole your rubber insert inside the wiper frame. Slide new rubber insert in the frame .

Feb 25, 2011 | 1995 Toyota Supra

1 Answer

How to replace the rear wiper blade on a 2008 Caravan, should be simple put it isn't like the front blades


pull on the middle of the rubber blade and pull it to the front of the blade holder and the back will come out then pull it the other way and the front will come out. then replace the new blade the opposite way.

Dec 13, 2010 | 2008 Dodge Grand Caravan

1 Answer

How to get the wiper blades off


these days the entire support and blade holder is replaced, gone are the days of the blade alone being changed. Typically, the arm disconnects where it connects to the blade holder.

Just change the whole thing, works better....

Oct 04, 2009 | 2005 Dodge Caravan

1 Answer

I have a 2000 dodge sport van with a problem passenger window.


Should be 2-3 screws holding it on. Remove the screws, get a trim stick, and pry the panel off. You will hear some plastic tabs pop out of their holders, but that is all.

Jun 09, 2009 | 2002 Dodge Caravan

1 Answer

Trying to replace driver side parking light on dodge nitro


You will need a flat blade screwdriver and a T20  torx Open the tailgate, on the inside of the lamp cluster there are 2 plastic domed heads that look like blanking plugs, with a flat bladed screwdriver pry them out, then grasp the lamp unit and pull it backwards, the 2 balls need to pop out of the plastic sockets and you will have the unit in your hand, on the back of the lamp the bulbholder is held in with 2 T20 torx screws, undo these and pry the holder out of the lamp, get someone to operate the lights and indicators to work out the faulty bulb, re-assemble in reverse order, pat the lamp into the panel with your hand.

Apr 05, 2009 | 2008 Dodge Nitro

1 Answer

I would like a dodge expert to help me with this problem


If the engine is a 2.7L. What is most likely wrong is his. The engine out of the 2001 has a different timing gear on the left cylinder head then the one on the 1998. In 1998 the engine computer is a SBEC controler(single board engine controler) an the 2001 is a NGC controler(next generation controler) the timing windows on those gears are in different positions. The controler doesnt know where the timing is.

Jan 16, 2009 | 1998 Dodge Intrepid

1 Answer

I,m taking out my intriped engine can it come up or do i have to


it is designed to be removed from the bottom after removing subframe with transmission together..then split...it is possible to do from top but nearly double the work

Dec 02, 2008 | 1999 Dodge Intrepid

Not finding what you are looking for?
2000 Dodge Intrepid Logo

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...