Question about 2000 Ford Taurus

1 Answer

Insterment panel dont work any more - 2000 Ford Taurus

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

Check fuses first could be a bad pannel and have to replace

Posted on Mar 11, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 1996 chrysler town and country insterments bounce around and the lights for the insterment panel flash what do you think is wrong


1) test the fuse for loose, or corrosion
2) tight the plug or connector very well.
3) see the diagram attached. and fix it.
God bless you
10_13_2012_1_14_41_pm.jpg

Oct 13, 2012 | 1996 Chrysler Town & Country

1 Answer

T urn signal flasher does not flash on my 1996 chevy blazer


do u mean ur turn signals do not flash an does the green turn signal arrow on ur insterment panel light upwhen u go to turn them on...if they dont flash an the arrow lites replace the turn signal flasher ..it is a round sliver cylinder located in the fuse box or under the dash on the steering column

Jul 14, 2011 | 1996 Chevrolet Blazer

1 Answer

Need to find out y my insterment cluster dont work


We assuming that you are refer at 1992 Mercedes Benz, the Flasher is located: Under hood, driver side, rear side of strut tower, mounted in relay block on upper firewall.

Keep in touch.

Feb 14, 2011 | 1992 Mercedes-Benz Mercedes Benz S Class

1 Answer

Installing Dash light bulbs in a 1993 S-10 Blazer


To replace the blubs you have to take out the insterment cluster. This is done by romoving the light switch trim plate and disconnect the wirering harness. The remove the A/C heater control panel. Remove the plastic trim from around the insterment cluster. The unbolt and remove the insterment cluster and uplug the wires and the speedometer cable. This speedometer cables can be a pain in the **** but depress the spring clip and pull. The bulbs are accessed from the back of the cluster.
Bulbs in this cluster don't burn out very often and if none of the bulbs don't work it probley isn't the bulbs. In this cause make sure the dimmer switch is turned up if it is play with the switch see if the dash light flicker.
Oh also in the mauals they always tell you to disconnect battery when pulling electrial apart.

Oct 20, 2010 | 1989 Chevrolet S-10 Blazer

1 Answer

Dash insterments dont work


Remove all fuses from the in car fuse box and check for any defective fuses, And when placing them back make sure they are fully slotted in.

It will just be a simple fuse problem.

Jun 23, 2010 | 1998 Dodge Grand Caravan

1 Answer

The insterment panel and rear parking lights went out


I have same problem. Fuses keep blowing in 1 to 2 days, which affect all interior & instrument cluster, parking/tail/turn signal, Lights which was 4 fuses. Good Luck & def. check fuses (3 locations)

Jun 01, 2010 | 1998 Honda Accord

1 Answer

Engine turns over, no fuel. fuel pumps not running. no electricity to enertia switch. no manual. dont know wich fuse. 1996 Ford F-250, 351, 5 spd, 2 wd.


the fuse should be under the left side of the hood if you are standing in front of the truck its going to be in the insterment panel with the relay and other things check that out and if the fuse is fine then check the wireing

Nov 05, 2009 | 1996 Ford F250 Crew Cab

1 Answer

Every once and a while my moms lincoln continetal starts beeping


somthing has gone rong with the insterment cluster. if all gages are working then i would just ignore it cause the insterment cluster is really pricey plus alot of labor to replace

Apr 18, 2009 | 1992 Lincoln Continental

1 Answer

Now knowing how to change the time on the clock


get the clock up on the insterment cluster then turn the right buttion in the insterment cluster and press in the set

Nov 17, 2008 | 2003 BMW 330

Not finding what you are looking for?
2000 Ford Taurus Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

fordexpert

Level 3 Expert

5572 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...