Question about 2001 Toyota Corolla

2 Answers

Day light sensor

My car is corrolla 2001.

Where is locate the day light sensor?
Can I remove this sensor?
I want to turn on and off the head lamp lights manually.

Thanks

Posted by on

2 Answers

Take your car to a Toyota dealer - they can easily make your head-lights turn on manually.

Posted on Sep 22, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 1,861 Answers

The sensor is on top of the dash panel, and it is a real job to remove it. It is a black dome-looking thing.

Posted on Sep 09, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 Malibu classic day time running lights resistor how to fine it


Hey Joe , the resistor you refer to is actually a light sensitive transistor , an it's called an ambient light sensor ! It is located in the top center of the dash pad , that little round bulb ! To replace it you have to Remove the instrument panel (I/P) trim pad. Are your Daytime Running Lamps (DRL) Inoperative ?
  1. Expose the ambient light sensor to a bright incandescent lamp.
  2. Turn ON the ignition, with the engine OFF.
  3. Place the headlamp switch in the OFF position.
  4. Ensure the parking brake is disengaged.
  5. Block the wheels.
  6. Place the transaxle in NEUTRAL.
Do the daytime running lights (DRL) illuminate?
??????

May 31, 2015 | 2005 Chevrolet Malibu

1 Answer

How do i replace the camshaft position sensor


On 2001-2005 vehicles the camshaft position sensor is mounted at the rear of the cylinder head. On 2006 vehicles, the camshaft position sensor is located on top of the engine, on the engine head cover.

Testing 2001-2003
  1. Connect the scan tool to the data link connector.
  2. Start the engine. Allow the engine to reach operating temperature.
  3. Monitor the CMPS signal. It should continuously fluctuate between 0-5 volts.
  4. If abnormality is found, replace the sensor.

Removal & Installation
  1. Disconnect the negative battery cable.
  2. Disconnect the connector from the sensor.
  3. Remove the bolt that retains the sensor.
  4. Remove the sensor.
To install:
  1. Installation is the reverse of the removal procedure.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Dec 22, 2011 | 2001 Kia Rio

1 Answer

Where do i check the bulb for day time running lights


The daytime running lamp is just the high-beam of the head light being fed a lower voltage so if the high beam works, but DRL does not, there's another issue -- to check the bulb, you'll have to remove the headlamp assembly; pop open the hood, and you'll have to remove to plastic covering that goes across over the radiator, there should be 2 bolts for each side that hold each in place, and it's a bit of a wiggle to get them out

Mar 26, 2010 | 2001 Chevrolet Cavalier

1 Answer

Head lamp wont work


Try replacing bulbs they could have both gone at the same time,I think it takes a 9006 bulb. You could check by pluging low beam plug into high beam bulb if it works the low beam bulbs are gone

Feb 06, 2010 | 2001 Pontiac Montana

1 Answer

My automatic headlights sometimes will come on by themselves when they're supposed to but most the time they don't. When they do however, they will only work for a couple days at a time and then, without...


you have day time running lights you are supposed to manualy turn them on at night. if you dont manually turn them on,on most cars the tail lights are not illuminated the automatic headlamps only turn the head lamps on. and they are controlled by the sensor located in the middle of your dash board

Jan 11, 2010 | 1992 Lincoln Town Car

1 Answer

My repair light turned on and my day lights keep beeping


Well you know the problem, go for it, replace the head light.
In the future, this is how it works.
Pull the E brake up before you start the car.
When you put it down the geen day time light will flash three times then the repair light will come on.
That means you have a burned out head light.

Dec 29, 2009 | 2001 Chevrolet Cavalier

1 Answer

Day time lights flashing until head are turned on


daytime running lamp module.....located behind and below drivers side headlamp access from wheel well

Nov 09, 2009 | 1996 Ford Taurus

3 Answers

Do you know the horn location for a 2002 chevrolet suburban 5.3L engine?


there is two on that vehicle, both located in the fenders one is located on the driver side near the washer jug (you have to take the jug out to get to it) and the passanger side is in the same basic location just on the rh side.

Jul 11, 2009 | 2003 Chevrolet Suburban 1500

1 Answer

Flashing lights


There is a photo sensor in your dash that turns your head lights on and off depending on light conditions, under certain daytime conditions the lights will come on, since i don't know your particular circumstances I can't say if there is a problem or not.

Oct 30, 2008 | 2001 Chrysler 300M

Not finding what you are looking for?
2001 Toyota Corolla Logo

Related Topics:

160 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...