Question about Volkswagen Golf

1 Answer

I have a 1998 vw golf one 1,3 , and need to change the head gasket .i need to know thetorque setting and bolt bolt sequence when tightening

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 232 Answers

Depending where you got the head gasket they will look it up for you just ask

Posted on Mar 11, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing head gasket


Hi
firstly, do you have the equipment to change the head gasket.
ie: a suitable torque wrench for the head bolts?
do you know how to re-time the engine having removed and refitted the timing belt(which you should renew)
I`mj looking at the worshop manual now and I presume you know how to strip an engine
The important part is when you replace the head (having made sure it`s not warped or cracked) and having cleaned all mating surfaces, you should have ten cylinder head bolts the tightening sequence is ____________________________
8 6 2 4 10


9 3 1 5 7
_____________________________

the torque settings are assuming you`rs is a M.40 engine is stage1 30 n/m stage 2: angle tighten 90 degrees stage 3 angle tighten 90 degrees.

Good Luck

Doug

Sep 05, 2013 | BMW Z3 Cars & Trucks

1 Answer

TORQUE SETTINGS FOR 1.4 16V 04 VAG ENGINE THEY USED IN SEAT LEON 04 16V 1.4.


Cylinder head instructions

Tightening sequence
tdisline_536.jpg
Cylinder head torque setting for 2004 VW 1.4L 16V fitted in Seat Leon
Renew bolts

Stage 1 = 30 Nm
Stage 2 = 90 degrees
Stage 3 = 90 degrees

May 17, 2011 | 2000 Volkswagen Golf

1 Answer

Torque setting for golf1 95mdl head bolts


CYLINDER HEAD TIGHTENING TORQUE [1] :
1st sequence: 40 Nm (30 ft lb)
2nd sequence: 60 Nm (43 ft lb)
Final sequence: plus 1/2 turn (180°)
torque sequence
10 4 2 6 8

7 5 1 3 9

Mar 02, 2011 | 1989 Volkswagen Golf

1 Answer

Want to know the amount of torque pressure do i use when tightening the head bolts, and whats the sequence?


To install:

0996b43f80208f65.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Cylinder head bolt torque sequence-3.8L engine

  1. Install the new cylinder head gasket with the arrow pointing to the front of the engine.
  2. Install the cylinder head.
  3. Install NEW cylinder head bolts. Torque the bolts in sequence, as follows:
    1. Step 1: 37 ft. lbs. (50 Nm).
    2. Step 2: Plus 120 degree turn.
To install:

0996b43f802316ea.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Tighten the cylinder head bolts using the following sequence-31L and 3.4L engines

  1. Install the cylinder head with a new gasket.
  2. Apply thread sealer to the head bolts.
  3. Tighten the cylinder head bolts to 37 ft. lbs. (50 Nm) plus an additional 90 degree turn.

Dec 16, 2010 | 2002 Pontiac Grand Prix

1 Answer

Can i change a leaking top gasket at home? I want to remove the head and have it skimmed.I am reasonally mechanical minded. What is the torque for fastening the top nuts? Manie vd Merwe. Jeffreys Bay


VOLKSWAGONS YOU NEED CYLINDER HEAD REMOVE SEQUENCE AND CYLINDER HEAD TORQUE SEQUENCE.YOU NEED A REPAIR MANUAL FOR TORQUE SEQUENCE OR YOU WILL HAVE HEAD GASKET LEAKS. TORQUE HEAD BOLTS TO * STEP 1 * TORQUE BOLTS 30 FT LBS * STEP TWO * TIGHTEN BOLTS 44 FT LBS STEP 3 TIGHTEN BOLTS PLUS 90 DEGREES.* STEP FOUR* TIGHTEN BOLTS PLUS 90 DEGREES AGAIN.

Oct 02, 2010 | 1999 Volkswagen Jetta

1 Answer

Need to know lbs of torque and sequence for the heads on a 1995 jeep wrangler with a 2.5


From autozone.com:
To install:

  1. Thoroughly clean the gasket mating surfaces. Remove all traces of old gasket material. Remove all carbon deposits from the combustion chambers. Lay a straightedge across the head and check for flatness. Total deviation should not exceed 0.001 in. (0.025mm).

The cylinder head gasket used on the 2.5L engine is a composition gasket. The gasket is to be installed dry. Do not use gasket sealing compound on the gasket.
  1. Fabricate 2 cylinder head alignment dowels from 2 used cylinder head bolts. Cut the head of the longest bolt off below the hex head. Then cut a slot in the top of the dowel to allow easier removal with a screwdriver.
  2. Install one dowel in bolt hole No. 10 and the other dowel in bolt hole No. 8.
  3. Place the cylinder head gasket over the dowels with the numbers facing up.
  4. Place the cylinder head over the dowels.
  5. Coat the threads of bolt No. 7 only, with Loctite PST sealant or equivalent.
  6. Install all head bolts except Nos. 8 and 10.
  7. Tighten the bolts in the sequence shown in the illustration to the following:
    1. Tighten bolts 1 through 10 in sequence to 22 ft. lbs. (30 Nm).
    2. Tighten bolts 1 through 10 in sequence to 45 ft. lbs. (61 Nm).
    3. Recheck bolts 1 through 10 in sequence to verify that they are 45 ft. lbs. (61 Nm).
    4. Tighten bolts 1 through 6 in sequence to 110 ft. lbs. (149 Nm).
    5. Tighten bolt 7 to 100 ft. lbs. (136 Nm).
    6. Tighten bolts 8 through 10 to 110 ft. lbs. (149 Nm).


During the final tightening sequence, bolt No. 7 will be tightened to a lower torque than the rest of the bolts. Do not overtighten bolt No. 7.
  1. Connect the temperature sending unit wire.
  2. Install the spark plugs.
  3. Install the compressor.
  4. Install the compressor/alternator bracket mounting bolt.
  5. Adjust the alternator drive belt.
  6. Install the air conditioning compressor drive belt.
  7. Install the intake and exhaust manifolds.
  8. Install the power steering pump bracket.
  9. Install the pushrods. Keep them in order!
  10. Install the rocker arms. Keep them in order!
  11. Thoroughly clean the mating surfaces of the head and rocker cover and install as outlined earlier in this section.
  12. Install the air cleaner.
  13. Connect the hoses at the thermostat housing.
  14. Connect the battery ground.
  15. Fill the cooling system.
  16. 1a34825.gif

Sep 23, 2010 | Jeep Wrangler Cars & Trucks

3 Answers

Need to know the head bolts torch specs on 98 toyota v6


heres the torque specs and the way to tighten the head bolts for your 1998 toyota sienna, hope this helps,
12 point bolts step 1- 40 ft lbs
step 2- additional 90 degrees
recessed bolt 13 ftlbsaf151d2.gif

May 12, 2010 | 1998 Toyota Sienna

1 Answer

Just want to retorque the head bolts hopeing to get lucky and solve a minor head gasket leak but dont know the specs


Torque settings are 110 ft LBS for nine of the ten bolts one bolt is 100 ft LBS /#1 Tighten all bolts in sequence 1 to 10 at 22 ft LBS #2 tighten all bolts 1 to 10 at 45 ft LBS #3 tighten all bolts 1 to 6 at 110 ft LBS #4 bolt #7 at 100 ft LBS #5 BOLT 8 TO 10 AT 110 FT LBS . HEAD TIGHTEN SEQUENCE - standing at front of car bolts down left side are 8/4/1/5/9 bolts down right side are 7/3/2/6/10. left side meaning distributor side. A four cylinder engine has ten (10) bolts. A six cylinder has fourteen (14) bolts.

Feb 16, 2010 | 1998 Jeep Cherokee

2 Answers

Need 1998 gmc sonoma diagram for 2.2 or 2.3 motor


the 2.2 engine top bolts from left to right is 8-4-1-5-9-your bottom bolts left to right is 7-3-2-6-10 this is your torque sequence.you need to use bolt thread sealer.wait 15 minutes before putting bolts in. you torque 46 ft lbs long bolts 43 ft lbs for short bolts.then you make second pass on all bolts tighten them additional 90 degrees using a torque angle meter.

Apr 07, 2009 | 1998 Chevrolet S-10 Pickup

1 Answer

What are the torque settings for the cylinder head 2000 subaru forester


This procedure is for the SOHC only.

E: INSTALLATION
1. CYLINDER HEAD

  1. Install cylinder head and gaskets on cylinder block. CAUTION: Use new cylinder head gaskets.
  2. Tighten cylinder head bolts.
  1. Apply a coat of engine oil to washers and bolt threads.
  2. Tighten all bolts to 29 Nm (3.0 kg-m, 22 ft. lbs.) in alphabetical sequence. Then tighten all bolts to 69 Nm (7.0 kg-m, 51 ft. lbs.) in alphabetical sequence.
  3. Back off all bolts by 180° first; back them off by 180° again.
  4. Tighten bolts (a) and (b) to 34 Nm (3.5 kg-m, 25 ft. lbs.) .
  5. Tighten bolts (c), (d), (e) and (f) to 15 Nm (1.5 kg-m, 11 ft. lbs.) .
  6. Tighten all bolts by 80 to 90° in alphabetical sequence. CAUTION: Do not tighten bolts more than 90°.



  1. Further tighten all bolts by 80 to 90° in alphabetical sequence shown in figure provided. CAUTION: Ensure that the total "re-tightening angle" [in the former two steps], do not exceed 180°.

May 24, 2008 | 2000 Subaru Forester

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

yadayada
yadayada

Level 3 Expert

78936 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...