Question about 1993 Oldsmobile Cutlass Ciera

3 Answers

I NEED TO SEE HOW TO CHANGE THE THERMOSTAT IT'S A 93

Posted by Anonymous on

Ad

3 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

If you have a 96 ciera- the thermostat is behind the exhaust crossover pipe

Posted on Dec 30, 2012

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Oldsmobile Master
  • 4,977 Answers

If you follow the upper rad hose to the motor that is were the thermostat is.the metal housing that the hose is clamped to is the thermostat housing and inside it is the thermostat,there should be 2 bolts that hold this housing on that need to be removed to change the thermostat.remove the thermostat and clean the surface were the gasket sits and clean the hole that the thermostat sits in.install the new thermostat with the spring facing the motor,then the gasket,then finish with reversal of removal.fill the radiator with coolant making sure the motor is hot(cooling fans run at least once) before installing the rad cap

Posted on Mar 11, 2011

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Oldsmobile Master
  • 17,970 Answers

See Figures 1, 2, 3 and 4

  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
CAUTION When draining the coolant, keep in mind that cats and dogs are attracted by ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.
  1. Some models require you to remove the air cleaner assembly from the throttle body.
  2. Some models with cruise control have a vacuum modulator attached to the thermostat housing with a bracket. It your vehicle is equipped as such, remove the bracket from the housing.
  3. On the 4-cylinder engines, unbolt the water outlet from the thermostat housing, remove the outlet from the housing and lift the thermostat out of the housing. On all other models, unbolt the water outlet from the intake manifold, remove the outlet and lift the thermostat out of the manifold.
I NEED TO SEE HOW - zjlimited_850.jpg

Fig. 1: Loosen the clamp securing the hose to the thermostat housing



Fig. 2: Remove the bolts securing the housing, then pull it away

zjlimited_852.jpg

Fig. 3: Make a note as to which end of the thermostat fits in the housing



To install:

  1. Clean both of the mating surfaces and run a 1 / 8 in. (3mm) bead of R.T.V. (Room Temperature Vulcanizing) sealer in the groove of the water outlet.
zjlimited_853.jpg

Fig. 4: Make sure both of the mating surfaces are free of any old gasket material

  1. Install the thermostat (spring towards engine) and bolt the water outlet into place while the R.T.V. sealer is still wet. Tighten the bolts 17-21 ft. lbs. (23-28 Nm) on all but the 2.2L engine. Other engines tighten to 89 inch lbs. (10 Nm).
  2. The remainder of the installation is the reverse of removal. Fill the cooling system, start the engine and top off. Check for leaks after the car is started and correct as required.

Hope helps (remember to rate and comment this answer).

Posted on Mar 11, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

93' toyota camry takes to long to warm up in the


Sounds like a dead spark plug or faulty wire, or even out of time. Start with changing plugs. No change, do the wires. No change check the timing belt. It may have jumped a cog. As for the slow to warm up part, the misfire won't help that problem, but you may need to change the thermostat if it doesn't improve once you get it running on all cylinders.

Feb 05, 2012 | 1993 Toyota Camry V6

1 Answer

How do I change my thermostat? 93 Dodge Grand Caravan SE


IT'S ON THE END OF THE TOP RADIATOR HOSE WHERE IT CONNECTS TO THE ENGINE. SHOULD BE 2-3 BOLTS GET NEW THERMOSTAT FIRST SHOULD COME W/GASKET. PAY CLOSE ATTENTION TO POSITION OF OLD THERMOSTAT SO YOU DON'T PUT NEW ONE IN UPSIDE DOWN.
GOOD LUCK

Dec 11, 2010 | 1993 Dodge Grand Caravan

1 Answer

Cant find thermostat on 93 model fuel injection


Your thermostat is located under a metal housing on the top of the engine. The upper radiator hose connects to this housing. To change the thermostat you basically need to drain the radiator after your engine is cold, disconnect the upper radiator hose from the engine, and remove the bolts from the small housing. replace the thermostat, and clean the surfaces on both sides and replace the gasket too. reinstall the housing, attach the hose, and refill the radiator. start the engine, warm it up and check for leaks, then re check the coolant level after the engine cools off again.

Feb 15, 2010 | 1993 Subaru Justy

1 Answer

I need to change the thermostat on a 93 plymoth acclaim...can sum1 plz tell me where it is located and how to go about it? the engine is a v-6


follow the upper radiator hose to where it attaches to the engine, remove hose clamp , thermostat is located in the housing remove the two or three bolts holding housing

Nov 07, 2009 | Plymouth Acclaim Cars & Trucks

1 Answer

How do u change the thermostat housing on the f150?? its a 93 straight 6..buddy broke the housing changing the thermostat and cant get the housing off to change it


this simply requires removal of hose and both attatching bolts of the housing to the block...restart all bolts by hand until properly started

Sep 27, 2009 | 1993 Ford F150 SuperCab

3 Answers

Need to find location od thermostat on 93 camry


try these websites www.autozone.com and www.alldatadiy.com and you should be able to get the information you need.

Jun 30, 2009 | 1993 Toyota Camry V6

1 Answer

Engine light on, scan code said thermostat


93 grand cherokee limited signal lights don't work could u help me/

Feb 16, 2009 | 2004 Pontiac Grand Prix

1 Answer

Grand cheroke 93 fuel filter


In HERE you can find the answer!!!

Good luck!!!

Oct 07, 2008 | 1993 Jeep Grand Cherokee

1 Answer

Thermostat problem


Hello, my 1997 4cyl. 2-wheel drive, temp gage automatically go to "H" as soon as you start it. I looked at the water pump,changed the thermostat and the cooling senser.When I take the connection off of the senser, the gage go to a normal giving reading (between H & C) already flushed it out what"s next?

Jul 04, 2008 | 1993 Toyota 4Runner

Not finding what you are looking for?
1993 Oldsmobile Cutlass Ciera Logo

326 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...