Question about Hyundai Sonata

1 Answer

The heater / blower control was only working on high and then when you wiggled it now not at all how do I get to this control knob? The dash seem to have only two screws that remove the bottom part under the steering wheel also I noticed that the ac does not light up when pushed either. Can you help me?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 504 Answers

Check reastat in blower housing/reastat controlls 1 2 3 speed for blower motor

Posted on Mar 11, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Heater relay location 2008 dodge magnum


There isn't one. There is for the A/C compressor and blower though. The blower is controlled by the resistor. The resistor can blow low speeds or high speeds, some cut out. The resistor is bad. If you have no blower. Unplug it and add power and ground to it. If it blows high. Look to replace the resistor. It takes diagnostics to see if the controller/ dash gauges/knobs is bad.

Dec 18, 2016 | Dodge Cars & Trucks

1 Answer

My heater blowers dnt work and i need to knw where i can locate the resister blocks for my heater blowers so i can ghange them


Its located under dash,or near glove box.

The dash panel lower side has to be out.

HEATER BLOWER MOTOR


Its faulty blower motor resistor. The low and medium speed on blower motor is controlled by resistor and its actual speed is high. So because resistor is not working, blower motors actual speed which is high is working.


It can be faulty blower motor or faulty blower motor resistor. Get the blower motor inspected. If it's faulty it has to be replaced.


=======

For blower motor testing and replacing, check the link below: ----

Blower motor Testing/replacing for all vehicles?

http://repairhelpcenter.blogspot.in/2012/02/blower-motor-replacing-for-all-vehicles.html

------------

These will help.

Thanks.

Nov 28, 2012 | Cars & Trucks

1 Answer

1995 Yukon blower and air direction do not work


I had the same problem. Fixed it by changing the climate control knob assembly on the dash. I was able to get a brand new one still in the box on ebay. Cost $150.00 the 1995 will not interchange with any other year even though others look similar the back is different. New they wil run into the $300.00 range. You get all knobs and switches including the push buttons for the AC. These units require a gentle touch easy to break. Good luck.

Nov 26, 2012 | 1995 GMC Yukon

1 Answer

Remove heater control switch


Before removing the heater switch on this 2006 citroen hdi I would first have the blower motor checked and the most common reason for this and other blower problems would be the blower resistor.

Your blower works on and off at times, first locate the blower motor and the resistor. the blower motor is located on the heater box, look under the pass/side of the dash, you may have to remove under dash cover to see blower.
When you have located the blower now look to the side on the heater box, there you will see a connector plug, it plugs into a connection on the heater box, this will be the resistor, the resistor slides into heater box and the end of it bolts to box to hold it in place and then the connector plugs into it, if you can not locate it then follow wires that plug into blower , follow wires back they will lead you to resistor,
next time blower does not work wiggle connector to resistor and see if blower turns on, if it does then resistor is the problem. also unplug resistor plug at resistor and check for any burning of connectors at plug and inside resistor.

I would bet its a bad resistor or the plug is brunt due to high draw from bad connections, if plug has burn damage to connectors then replace the plug along with resistor.

Jul 08, 2012 | 2006 Citroen C5 HDi

1 Answer

Control knob for heater/ac works on high only.


This problem is caused by the blower speed control resistor being defective for the blower motor. The resistor is located near the blower motor under the dash.

Apr 19, 2011 | 2007 Nissan Titan LE

2 Answers

2005 jeep AC and heater blower only high speed works


check fuses, then wiggle speed control while moving, may need new dash control for lower speed, usually high speed works through relay may be the reason high speed works

Nov 03, 2010 | 2005 Jeep Grand Cherokee

1 Answer

Heater Fan does not work


Sounds like the fan control knob has shorted out. You can check the fan "blower" relay and fuse in the engine compartment but you need to make sure the control knob is good or you will keep blowing fuses and relays. If your blower fuse and relay are good, then just have the control knob checked and replaced if needed.

May 08, 2009 | 1999 Volkswagen Passat

1 Answer

Why the heater motor/blower control knob works only on high,if i put it in low/medium range, it will turn-off


Very common when heater blower motor "Resistor" goes bad. In most cases they are either located under hood on firewall, passenger side, or under dash, passenger side, near blower motor. If I can confirm on location of it, I'll get back to you.

Mar 13, 2009 | 1997 Ford Taurus

1 Answer

Blower for heater stopped


Remove the hush panel under the dash and unplug your blower motor turn the knob and see if its getting power. If it is replace the blower motor. If your heater seems to work on high but not the other 4 settings. replace the blower motor resistor and pigtail (same general location as blower motor)

Jan 31, 2009 | 2004 Chevrolet Silverado 2500HD

2 Answers

Heater control 98 chevy s10 blazer


These trucks have a problem where moisture builds up in the heater box then freezes. When this freezes and you change your heater settings it breaks the shaft for the blend door. If this is what happened you should be able to look under the dash above and to the right of the gas pedal and you will see two vaccuum accuators one of them you should be able to wiggle around the linkage if it is broke. To fix this you need to remove the entire dash to get the heater box out which involves discharging the AC and draining the coolant because the heater core and evaporator come out. Please rate.

Dec 13, 2008 | 1996 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

134 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...