Question about Dodge Neon

1 Answer

What is this code for just got it today p1192 is the code

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 504 Answers

Catalyst Fuel Trim System Bank 1,code p1192

Posted on Mar 11, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

1996 GMC W35042 TROUBLE CODE P1192

what sort of a truck is this ?
W35042 confuses me
diesel or petrol

mess of problems


fuel injectors

trans axle/transmission


Oct 13, 2016 | GMC Cars & Trucks

1 Answer

Odb code p1192 santa fe2003 3.5 mechanic told me to replace whole throttle system.

TPS (Throttle Position Sensor) Diagnosis and Unde…: maybe this will help you from what i understand iif itis your tps malfunctioning it will need to be rwplaced

May 01, 2015 | 2003 Hyundai Santa Fe

1 Answer

1193 p1192 p0115 hunday 300 xg

p1193.p1192 Ets has entered limp in mode low rpms po115 engine coolant temp malfunction

May 25, 2014 | Hyundai Cars & Trucks

2 Answers

Codes p1192 an po700

P1192 has to do with Intake Air Temp. That sensor might be bad. The P0700 has to do with Transmission Control. Whether it's the control module or something else is hard to say at this point. However, if the vibration is really in the front of the vehicle, I would start by checking UJoints on the front drive shaft, CV Joints and the Transmission Mount/Motor Mounts. Make sure your transmission fluid level is correct. The shaking "under a load" is likely a torque converter issue. I had the same problem on my 96 Suburban. Instead of rebuilding the transmission (or changing the torque converter), there is a product available called "Dr. Tranny Shudder Fixx". Small tube, put in with Transmission Fluid, shudder goes away almost instantly. Hope this helps.

Jan 26, 2014 | 1996 GMC Sierra

1 Answer

P1192 trouble code

You will have to use Google & put in your vehicle
as well as the OBD Code
That is not a generic code
200? Hyundai model ? OBD P1192

Jul 13, 2013 | Hyundai Cars & Trucks

1 Answer

I have a2001 plymouth neon that will not idle. The error codes are P1192 P1193 and P0508 what are they? How do I fix them? Where do I get the parts? I NEED MY CAR BACK

ok here we go p1192 -IAT CIRCUT LOW (intake air temp sensor circuit indicater low.
p1193 is the same but all circuits are high.
could not find po508 on plymouths are you sure of code #.
code po505(idle air control motor circuits)

Sep 24, 2012 | Cars & Trucks

1 Answer

Engine code p1192

look for a bad o2 sensor a scan tool reading would help could be cheaper to replace it and try it

May 30, 2012 | 2002 Chrysler Sebring

1 Answer

Chevy Tahoe with a p1192 code...can you tell me what this means/indicates?

P1192 - Post-catalyst Fuel Trim System Bank 1
this is what your code is coded as, hope this helps get you started.
bank 1 im assuming oxygen sensor.

Dec 08, 2010 | Chevrolet Tahoe Cars & Trucks

1 Answer

I have trouble codes P0700 (transmission control module?) and P1192 (undefined code) on a 1996 Safari Van. Anybody have any definitions/suggestions? Already been on diagnostics.

P1192 Post-catalyst Fuel Trim System Bank 1 Check your Oxygen Sensor Heater Circuit, could be dirty or loose wires or just stop working. Usually you have 4 of these under your car so check all. Fault Code P0700

Here's what my service manual says:

EATX Controller DTC Present

This SBEC III or JTEC DTC indicates that the EATX or Aisin controller has an active fault and has illuminated the MIL via a CCD (EATX) or SCI (Aisin) message. The spscific fault must be acquired from the EATX via CCD or from the Aisin via ISO-9141.

Here's what I know: MIL=malfunction indicator light; DTC=diganostic trouble code; CCD=Chrysler collision detection. Beyond that, I'm clueless. Sounds like it needs to be read out at the dealer. Then again, if it was a one-time glitch, it might clear itself after several drive cycles.

Mar 17, 2009 | 1996 GMC Safari

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

545 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

80339 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides