Question about 1988 Dodge Dakota

Open Question

How to remove Dodge Dakota Ignition Lock Cylinder?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: ignition lock cylinder

take the registration or title to your local dealer and have a key made from the VIN

Posted on Jun 30, 2008

Ad
  • 16 Answers

SOURCE: replace ignition lock cylinder 1996 BMW 318i with 1995 BMW

no you can not

Posted on Mar 12, 2009

SOURCE: need to replace 280zx ignition lock cylinder

we have a 71-681. we don't have a key.

Posted on Apr 17, 2009

co7196
  • 3433 Answers

SOURCE: ignition lock cylinder removal

turn to accessory and use straight paper clip yo pud pi inside the hole in front of the key while turning key to on and pulling out using key for a handle.

Posted on Sep 24, 2009

  • 29 Answers

SOURCE: 1990 dodge dakota cooling system capacity???

at the max two gal, mix 50/50

Posted on Oct 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Lost key for 1999 Chrysler Cirris.need to replace ignition lock cylinder


take center of steering wheel off,access the star screw through a hole in the wheel to remove mechanism

Jul 23, 2015 | Chrysler Cars & Trucks

2 Answers

How do i change out the ignition switch?


Ign Systems 8D - 19 Service manual '92 Dak
Disconnect neg battery cable Tilt column:Remove tilt lever (counterclockwise) Remove upper and lower covers (3 screws) Remove ign switch mounting screws (3) with torx bit Gently pull switch away from column Release two connector locks on the seven-terminal wiring connector. Remove connector from ign switch Release connector lock on the Key-in-switch and Halo Light four terminal connector. Remove connector from switch Remove key cylinder from switch as follows: With key inserted and ign switch in the LOCK position use small screwdriver to depress the key cylinder retaining pin flush w/ key cylinder surface Rotate the key clockwise to the OFF position The key cylinder should now be unseated from the ign switch assembly With key cylinder in unseated position (key cylinder bezel about 1/8 inch above ign switch halo light ring) Rotate key counterclockwise to LOCK position and remove key Remove key cylinder INSTALLATION; Install electrical connectors to switch making sure locking tabs are fully seated into connector Mount ign switch to column Shifter must be in PARK position Park-lock dowel pin on ign assy must engage with park-lock slider linkageVerify ign switch is in lock position (flag is parallel w/ ign switch terminals..off to the right) Apply dab of grease to flag and pin Position park-lock link and slider to mid-travel Position ign switch against lock housing face Be sure pin is inserted into park-lock link contour slot Tighten screws Assemble cover Tighten more screws Tilt column and install tilt lever (clockwise) instsall neg battery cable Gently insert key cylinder into ign switch asssy until it bottoms Insert key and gently push key (inward) and rotate clockwise to end of travel Rejoice in how much money you just saved yourself

Jun 16, 2014 | 1992 Dodge Dakota

1 Answer

How do i tear apart my steering column in my 84 dodge pickup so i can change my ignition switch?


  1. NON TILT WHEEL
  2. Remove the steering wheel.
  3. Remove the turn signal switch.
  4. Unfasten the two screws that release the buzzer switch (if equipped), then remove the switch.



0900c15280052e49.jpg

Fig. Fig. 2: Removing the ignition buzzer

  1. Remove the retaining screw and lift the ignition lock cylinder lamp out of the way.



0900c15280052e4a.jpg

Fig. Fig. 3: Ignition key lamp

  1. Remove the bearing housing.
  2. Detach the coil spring.
  3. Remove the lock plate from the shaft.



0900c15280052e4b.jpg

Fig. Fig. 4: Lock lever plate removal

  1. Unfasten the 2 retaining screws and lift the lock lever guide plate to expose the lock cylinder release hole.
  2. Insert the key and place the lock cylinder in the LOCK position. Remove the key.
  3. Insert a thin punch into the lock cylinder release hole and push inward to release the spring-loaded lock retainer. At the same time, pull the lock cylinder out of the column.



0900c15280052e4c.jpg

Fig. Fig. 5: Depress the lock plate which will expose the lock cylinder release hole

  1. Remove the 3 retaining screws and lift out the ignition switch.

To install:
  1. Position the ignition switch in the center detent position (OFF).
  2. Place the shift lever in PARK.
  3. Feed the wires down through the space between the housing and jacket. Position the switch in the housing and install the 3 retaining screws.



0900c15280052e4d.jpg

Fig. Fig. 6: Lock levers and spring assembly installed

  1. Place the lock cylinder in the LOCK position, and press it into place in the column. It will snap into position.
  2. The remainder of assembly is the reverse of disassembly.

Aug 14, 2011 | 1984 Dodge Pickup 4WD

1 Answer

How do you replace the ignition switch on a 1989 dodge dakota?


Remove the steering column cover,I believe a long T20 Torx Bit

Then same Torx, for switch

Your not doing the key cylinder

Dec 07, 2010 | 1989 Dodge Dakota 2WD

1 Answer

How do you change the ignition lock cylinder on a 1990 dodge dakota?


I just recently had to replace the ignition lock cylinder on a 1990 Dodge Dakota. If yours is anything like mine the ignition lock cylinder you need is for a 1989 Dodge Dakota. All you have to do to replace it is remove the center of the steering wheel and the steering wheel. Next you will have to remove the lock plate. After you do that you should be able to pull everything else out of the way. Then all you have to do is take a flathead screw driver and pop the old ignition out. You will need a steering wheel puller and a steering wheel lock plate remover. The best thing to do with the lock cylinder is to go to autozone or whatever store you use and match it up. Good luck

Nov 28, 2010 | 1990 Dodge Dakota

1 Answer

How do i remove the steering column cover to get at the ignition tumbler on a 1993 dodge dakota


CAUTION Disconnect and isolate the negative (ground) battery cable. This will disable the air bag system. Failure to disconnect the battery could result in accidental deployment and possible personal injury. Allow the system capacitor to discharge for two minutes then begin air bag system component removal. To install:
  1. Engage the electrical connectors to the ignition switch and make sure the switch locking tabs are fully seated.
  2. Before attaching the ignition switch to a tilt steering column, the transmission shifter must be in the PARK position. Also the park lock dowel pin and the column lock flag must be properly indexed before installing the switch as follows:
    1. Place the transmission shifter in the PARK position
    2. Place the ignition switch in the LOCK position. The switch is in the lock position when the column lock flag is parallel to the ignition switch terminals.
    3. Position the ignition switch park lock dowel pin so it will engage the steering column park lock slider linkage.
    4. Apply a light coating of grease to the column lock flag and the park lock dowel pin.
  3. Place the ignition switch against the lock housing opening on the steering column. Ensure that the ignition switch park lock dowel pin enters the slot in the park lock slider linkage in the steering column.
  4. Install the retaining bracket and ignition switch mounting screws, then tighten the screws to 22-30 inch lbs. (3-4 Nm).
  5. If the vehicle is equipped with a tilt steering column, install the tilt lever.
  6. With the key cylinder and the ignition switch in the LOCK position, insert the key cylinder into the ignition switch until it bottoms.
  7. Insert the ignition key into the lock cylinder. While pushing the key cylinder in toward the ignition switch, rotate the ignition key until the end of travel.
  8. Install the retaining screw into the bracket and lock cylinder. Tighten the screw to 22-30 inch lbs. (3-4 Nm).
  9. Install the steering column covers, then the tilt lever, if equipped.
  10. Connect the negative battery cable.
  11. Check for proper operation.


ec3f7ac.jpg

eff2c5f.jpg

72e2667.jpg

7a1362b.jpg

Jul 30, 2010 | 1993 Dodge Dakota

1 Answer

#2 cylinder misfiring on a 2001 dodge dakota


If plugs are receiving ignition then I would have a compression test run on that #2 cylinder. Good Luck Darrell S

Jun 12, 2010 | 2001 Dodge Dakota

1 Answer

Can i order a key for a 1993 dodge dakota


You can call a dodge dealer, give them the vin# and
they used to be able to cut you a key from that.
But if that method is obsolete, you can try this.
If your key was original equipment, roll the window up
and remove the door panel. Remove the clip from the
linkage rod on the door lock. Remove the spring clip
from the door lock assy. and remove the lock.
The door and ignition lock use the same key. Take
the door lock to a locksmith and they will make a
key for you. Hope this helps.

Feb 05, 2010 | 1993 Dodge Dakota

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

250 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...