Question about Cadillac SRX

2 Answers

I have codes p0008 and p0017 ,car is low on power ,reader says cam and crank position sensors,can you just replace these, its a2004 srx cady, thanks!!

Posted by on

  • mnt1 Jul 31, 2008

    thanks!!!!

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cadillac Master
  • 19,396 Answers

Timing chain problems

Posted on Jul 31, 2008

  • Ginko
    Ginko Jul 31, 2008

    Well I won't say easily, codes p0008 and p0017 are primary drive and secondary drive timing chainserror. You will have check or to replace both primary drive and secondary drive timing chains, I think you need a mechanic to do this.
    On this page you find the how to:

    Cadillac : failed timing chain

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 2,028 Answers

Both of these are easily replaceable, and should take care of the problem.

Posted on Jul 31, 2008

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change a csmshsft sensor on a 2008 cadillac srx


Before you replace a part you may or may not need . Why ? What code ? Does the vehicle run ? There has been a lot of confusion on these vehicles with variable valve timing , mixing up cam sensors with camshaft actuators
DTC P0008: Engine Position System Performance Bank 1

DTC P0009: Engine Position System Performance Bank 2
The presence of DTCs P0008 and P0009 along with P0016, P0017, P0018, and P0019 indicates a possible condition with the primary timing chain and the alignment between both intermediate sprockets and the crankshaft. Or, the crankshaft reluctor wheel has moved and is no longer referenced to top dead center (TDC).


?€¢
Observe the scan tool CMP Desired, Actual, and Angle Variance parameters before a DTC sets. This may help to isolate whether a condition is specific to one camshaft, one bank, or caused by a condition with the primary crankshaft timing.



DTC Descriptors
DTC P0010: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit Bank 1

DTC P0013: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit Bank 1

DTC P0020: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit Bank 2

DTC P0023: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit Bank 2

DTC P2088: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit Low Voltage Bank 1

DTC P2089: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit High Voltage Bank 1

DTC P2090: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit Low Voltage Bank 1

DTC P2091: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit High Voltage Bank 1

DTC P2092: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit Low Voltage Bank 2

DTC P2093: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit High Voltage Bank 2

DTC P2094: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit Low Voltage Bank 2

DTC P2095: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit High Voltage Bank 2
DTC P0341: Intake Camshaft Position (CMP) Sensor Performance Bank 1

DTC P0342: Intake Camshaft Position (CMP) Sensor Circuit Low Voltage Bank 1

DTC P0343: Intake Camshaft Position (CMP) Sensor Circuit High Voltage Bank 1

DTC P0346: Intake Camshaft Position (CMP) Sensor Performance Bank 2

DTC P0347: Intake Camshaft Position (CMP) Sensor Circuit Low Voltage Bank 2

DTC P0348: Intake Camshaft Position (CMP) Sensor Circuit High Voltage Bank 2

DTC P0366: Exhaust Camshaft Position (CMP) Sensor Performance Bank 1

DTC P0367: Exhaust Camshaft Position (CMP) Sensor Circuit Low Voltage Bank 1

DTC P0368: Exhaust Camshaft Position (CMP) Sensor Circuit High Voltage Bank 1

DTC P0391: Exhaust Camshaft Position (CMP) Sensor Performance Bank 2

DTC P0392: Exhaust Camshaft Position (CMP) Sensor Circuit Low Voltage Bank 2

DTC P0393: Exhaust Camshaft Position (CMP) Sensor Circuit High Voltage Bank 2
I'm sorry but when dealing with these problems your best bet is to take your vehicle to a qualified repair shop , I have never see a DIY'ER correct the problem with these , an in the end always end up taking it to the dealer .

Jul 24, 2016 | 2008 Cadillac Srx

1 Answer

P0016 and P0017 check engine pop up after i run for 10 to 15 miles?


the common causes for code P0017 are as follows:
  • A faulty cam or crank sensor
  • The cam or crank circuit is open or shorted
  • The timing belt/chain is out of time
  • The cam or crank tone ring is slipped/broken
  • A problem in the VVT system P0016 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A) P0017 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor) God Bless! Hope this helps you.

Mar 08, 2016 | Cars & Trucks

2 Answers

HOW TO FIX P0017 ERROR ON 2007 HHR


Well the code means there is a problem with the cam sensor position for bank 2. The sensor is telling the engine computer the cam is in a different position that it should be.
You would need to check the signal from the sensor, and the actual cam to find the problem.

Feb 16, 2015 | 2007 Chevrolet HHR Special Edition

1 Answer

Volvo code p0017


Ok, P0017 = Cam/Crank Position Correlation Sensor B Bank 1, so that's your Camshaft Position sensor ; which could be either faulty or set in the incorrect position.

Jul 10, 2014 | 2005 Volvo S60

2 Answers

Pcm?


PCM= Powertrain Control Module. It is the brains of the car, it reads the sensor in put from all sensors including the cam shaft position sensor

May 14, 2014 | 2004 Toyota 4Runner

1 Answer

P0017


The generic code is for the correlation between the crank sensor and the cam sensor on bank one sensor 2 or B.
The computer is not finding the cam in the right position based on the crank sensor and the other cam sensors.
Code 17 for Chevrolet may be different.

Jul 18, 2012 | Chevrolet Cars & Trucks

3 Answers

I have a p0008 code & I'm worried


P0008 CADILLAC - Engine Positions System Performance Bank 1
The ECM detects that both camshafts on either bank of the engine are mis-aligned with the crankshaft for more than 4 seconds or a cumulative of 50 seconds.

The Engine Control Module (ECM) monitors the position of both camshafts and the crankshaft. The ECM performs a test for misalignment between both camshafts on one bank of the engine and the crankshaft. During the test the ECM learns the position of the camshafts and the crankshaft. While the engine is idling, the ECM compares the position of both the camshafts and the crankshaft with the learned value. The ECM will set the P0008 code if both learned values for one bank of the engine are exceeding a calibrated threshold in the same direction.

Symptoms
- Engine Light ON (or Service Engine Soon Warning Light)

Possible causes
- Engine mechanical problems
- Incorrect timing chain
- Stretched timing chain
- Failed camshaft actuator or actuator solenoid

Tech notes
There is a factory service bulletin for the following Cadillac models:

2004-2008 Cadillac CTS SRX
2005-2008 Cadillac STS

The service bulletin suggest replacing the primary drive and both secondary drive timing chains. Contact your Cadillac dealer for more information. The repair could still be cover under factory warranty.


Hope this helps (remember to rate this answer).

Jun 02, 2011 | Cadillac SRX Cars & Trucks

1 Answer

3.6 in a 2006 pontiac g6 is throwing code p0017 is this crank sensors or what is the most common fix


P0017 - Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor B)

The crankshaft position sensor (CKP) and Camshaft position sensor (CMP) work in harmony to control the spark/fuel delivery and timing. They both consist of a reluctor, or tone, ring which passes over a magnetic sensor, which generates a voltage, indicating position.

The crankshaft sensor is part of the primary ignition system and functions as the "trigger". It detects the position of the crankshaft relays that information on to the PCM or the ignition module (depending on the vehicle) to control spark timing. The Camshaft position sensor detects the position of the camshafts and relays the information to the PCM. The PCM uses the CMP signal to identify the beginning of the injector sequence. What ties these two shafts and their sensors together is the timing belt or chain. The cam and crank should be precisely timed together. If the PCM detects that the Crank and Cam signals are out of time by a specific number of degrees, this P0017 code will set.

Symptoms of a P0017 will or may include:
* Malfunction Indicator Lamp (MIL) illumination
* The engine may run but with reduced performance
* The engine may crank but not start
* The engine may exhibit a rattle near the harmonic balancer indicating the tone ring is damaged
* The engine may start and run, but poorly

Causes may include:
* Timing chain stretched, or timing belt skipped a tooth due to wear
* Misalignment of timing belt/chain
* Tone ring on crankshaft slipped/broken
* Tone ring on camshaft slipped/broken
* Bad crank sensor
* Bad cam sensor
* Damaged wiring to crank/cam sensor
* Timing belt/chain tensioner damaged

Possible Solutions:
1. First, visually inspect the cam and crank sensors and their harnesses for damage. If you notice broken/frayed wires, repair and recheck.
2. If you have access to a scope, check the cam and crank patterns. If a pattern is missing, suspect a bad sensor or a slipping tone ring. Remove the cam gear and the crankshaft harmonic balancer and inspect the tone rings for proper alignment and make sure they're not loose or damaged or that they haven't sheared the key that aligns them. If they are properly installed, replace the sensor.
3. If the signal appears normal, then check the timing chain/belt for proper alignment. If it's misaligned, check for a damaged tensioner that may have allowed the chain/belt to slip a tooth or several teeth. Also check that the belt/chain isn't stretched. Repair and recheck.

Other crank sensor codes include P0016, P0018, P0019, P0335, P0336, P0337, P0338, P0339, P0385, P0386, P0387, P0388, and P0389.


Hope this helps (remember to rate and comment this answer).

Nov 23, 2010 | 2006 Pontiac G6

2 Answers

Jaguar xj 40 sovereign 1994 error code 17


I'm not a Jag expert, but error code 17 is:
P0017 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor B)
Additional infomation on and cause and possible solutions are here:
http://www.obd-codes.com/p0016
Basically, it looks like you have timing issue. Could be the cam or crank sensor or the timing belt.
The P0017 code would imply that you have at least two cam sensors (V6 or V8). The computer thinks that the B sensor cam is out of time with the other cam and the crankshaft. Depending on the cost and location, you might try changing the cam sensor first. The cost to check or replace the timing belt is probably going to be painful.

Jun 12, 2010 | 1994 Jaguar XJ6

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,390 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...