Question about 1995 Subaru Impreza

1 Answer

Generator problem - 1995 Subaru Impreza

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Subaru Master
  • 22,156 Answers

Start engine with engine running disconnet the neg terminal on the battery if engine keeps going then its a battery fault if engine stops straight away then its a alternator fault

Posted on Mar 11, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need simple instructions on installing alternator in 98 ford escort


SECTION 414-02: Generator and Regulator 1998 Escort/Tracer Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 03/05/1998 Generator-Sedan and Wagon Removal
  1. Disconnect the battery ground cable.

  1. Remove the generator drive belt.
    1. Release the tension on the drive belt.
    1. Remove the drive belt from the generator pulley.
  1. Disconnect the HO2 sensor harness clip from the generator bracket.
  1. Position the generator bracket aside.
    1. Remove the A/C line bracket bolt.
    1. Remove the power steering pressure line bracket bolts.
    1. Remove the generator bracket bolts.
    1. Position the generator bracket aside.
  2. gj1399b.gif
  1. Remove the generator bolts and position the generator aside.ddll111_14.gif
  1. Remove the generator.
    1. Disconnect the two generator electrical connectors.
    1. Remove the battery positive nut and washer.
    1. Disconnect the battery positive cable and remove the generator.ddll111_16.gif
Installation
  1. NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
    To install, reverse the removal procedure.

2010&c18=modelyear&c20=n41406&c35=wsm%2cgenerator%u2014sedan%20and%20wagon%2cswf%2c414-02%2cremoval%20and%20installation&s=1366x768&c=32&j=1.3&v=y&k=y&bw=995&bh=428&ct=lan&hp=n&[aqe]

Mar 10, 2011 | Ford Escort Cars & Trucks

1 Answer

Alternator mounting diagram


1999-2005 To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following:
    • The negative battery cable
    • The windshield wiper system module cover (if equipped)
    • The fuel injector sight shield (if equipped)
  3. Rotate and secure the engine forward.
  4. Remove or disconnect the following:
    • The generator B+ terminal nut chev_vent_99-05-alt-ec.gif

    • The generator B+ lead
    • The generator electrical connector
    • The drive belt from the generator gm_mv_ven_altbolt.gif

    • The generator front bolt gm_mv_ven_altrear.gif

    • The generator rear bolts gm_mv_ven_altbrack.gif

    • The generator from the generator bracket and position the generator above the drive axle
    • The drive belt tensioner
    • The generator bracket
    • The power steering pipes from the power steering pipe retainer
    • The fuel pressure test port (schrader valve) cap from the fuel injector rail NOTE: Do not disconnect the power steering pipes from the power steering pump.
    • The power steering pump and reposition in front of the timing chain cover in order to provide access for the generator
    • The generator from the vehicle
To Install:
  1. Install or connect the following:
    • The generator to the vehicle into position above the drive axle
    • The power steering pump to the engine
    • The fuel pressure test port (schrader valve) cap to the fuel injector rail
    • The power steering pipes to the power steering pipe retainer (if removed)
    • The generator bracket
    • The drive belt tensioner
    • The generator to the generator bracket and position the generator above the drive axle
    • The drive belt tensioner
    • The generator to the generator bracket
    • The generator front bolt
      1. Torque to: 37 ft. lbs. (50 Nm)
    • The generator rear bolts
      1. Torque to: 37 ft. lbs. (50 Nm)
    • The drive belt
    • The generator electrical connector
    • The generator B+ lead
    • The generator B+ terminal nut
      1. Torque to: 115 inch lbs. (3 Nm)
  2. Position the engine rearward.
  3. Install or connect the following:
    • The engine mount strut bracket bolts
    • The fuel injector sight shield
    • The windshield wiper system module cover
    • The negative battery cable
prev.gif next.gif
for removal to reposition the engine

Feb 15, 2011 | 2000 Pontiac Montana

1 Answer

1998 ford escort altinator two bolt or three bolt? engine light is on brand new battery and the battery light is on . car just died when driving waited 7mins and it started .is it the altinator


check with volt meter. 12 volts with engine off. Should be 14 volts with engine running if alternator is working.
First, clean battery posts and cable ends. Then check owner manual for fuse locations and blown fuses. There is a large 100 amp fuse in box under hood.

Is the battery lamp lit on the dash?

Looks like 3 bolts. please rate when done

SECTION 414-02: Generator and Regulator 1998 Escort/Tracer Workshop Manual
REMOVAL AND INSTALLATION Generator -Sedan and Wagon Removal
  1. Disconnect the battery ground cable.
  1. Remove the generator drive belt.
    1. Release the tension on the drive belt.
    1. Remove the drive belt from the generator pulley.
  1. Disconnect the HO2 sensor harness clip from the generator bracket.

  1. Position the generator bracket aside.
    1. Remove the A/C line bracket bolt.
    1. Remove the power steering pressure line bracket bolts.
    1. Remove the generator bracket bolts.
    1. Position the generator bracket aside.
  1. Remove the generator bolts and position the generator aside.
  1. Remove the generator.
    1. Disconnect the two generator electrical connectors.
    1. Remove the battery positive nut and washer.
    1. Disconnect the battery positive cable and remove the generator.
step 4
snorkelbobby_37.gif

Feb 12, 2011 | 1998 Ford Escort

1 Answer

How to change the alternator on my 2000 grand voagear


This is for a 3.3L motor
Hope this helps, it it does please leave feedback and vote Thank You and Good Luck

REMOVAL

  1. Release hood latch and open hood.
Removal/Installation of Battery Cables 81929864

  1. Disconnect battery negative cable.
  2. Remove windshield wiper housing, refer to the Windshield Wipers and Washers for proper procedures.
  3. Remove accessory drive belt.
Generator Mounting Bracket 81929870

  1. Remove bolt holding top of generator mount bracket to engine air intake plenum.
  2. Remove bolts holding outside of generator mount bracket to generator mount plate.
  3. Remove bolt holding top of generator to mount bracket.
  4. Remove generator mount bracket from vehicle.
  5. Rotate generator toward rear dash panel.
Generator 81929868

  1. Disconnect the push-in field wire connector . from back of generator.
  2. Remove nut holding B+ wire terminal to back of generator.
  3. Separate B+ terminal from generator.
Generator Pivot Bolt 81929871

  1. Remove bolt holding bottom of generator to lower pivot bracket.
Generator 81929872

  1. Remove generator from vehicle
INSTALLATION

  1. Place generator in position on vehicle.
  2. Install bolt to hold bottom of generator to lower pivot bracket.
  3. Place B+ terminal in position on generator.
  4. Install nut to hold B+ wire terminal to back of generator.
  5. Connect the push-in field wire connector into back of generator.
  6. Rotate generator forward away from dash panel.
  7. Place generator mount bracket in position on vehicle.
  8. Install bolt to hold top of generator to mount bracket.
  9. Install bolts to hold outside of generator mount bracket to generator mount plate.
  10. Install bolt to hold top of generator mount bracket to engine air intake plenum.
  11. Install accessory drive belt.
  12. Install windshield wiper housing, refer to the Windshield Wipers and Washers for proper procedures.
  13. Connect battery negative cable.
  14. Verify generator charge rate.

Jan 02, 2011 | 2000 Plymouth Grand Voyager

1 Answer

How does the alternator bracket go on


Remove the accessory drive belt. Disconnect the negative battery cable. Disconnect the generator electrical connector. Remove the engine harness terminal from the generator: - Slide the boot back along the cable. - Remove the engine harness cable nut (3). - Remove the engine harness terminal from the stud. Remove the generator bolts and generator. Install the generator. Install the generator bolts. Tighten the generator bolts to 50 N?m (37 lb ft). Install the engine harness terminal to the generator: - Install the engine harness terminal to the stud. - Install the engine harness cable nut (3). Tighten Tighten the engine harness cable nut to 13 N?m (10 lb ft). - Slide the boot over the generator stud. Connect the generator electrical connector (1). Connect the negative battery cable. Refer to Battery Negative Cable Disconnect/Connect Procedure . Install the accessory drive belt

Dec 24, 2010 | 2001 Chevrolet Impala

1 Answer

Car not starting... Seems like battery isnt charging due to faulty alternator


did you have alternator and battery tested Disconnect the battery ground cable.

Remove the generator drive belt.
Release the tension on the drive belt.
Remove the drive belt from the generator pulley.

Disconnect the HO2 sensor harness clip from the generator bracket.

Position the generator bracket aside.
Remove the A/C line bracket bolt.
Remove the power steering pressure line bracket bolts.
Remove the generator bracket bolts.
Position the generator bracket aside.

Remove the generator bolts and position the generator aside.

Remove the generator.
Disconnect the two generator electrical connectors.
Remove the battery positive nut and washer.
Disconnect the battery positive cable and remove the generator.

Installation

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.

To install, reverse the removal procedure.

Dec 18, 2010 | 1998 Ford Escort

1 Answer

How to remove alternater 2005 mercury mariner 3.0 v-6


Removal and Installation

  1. CAUTION: Do not allow any metal object to come in contact with the generator housing and internal diode cooling fins. A short circuit may result and burn out the diodes. Disconnect the battery.
  2. Remove the RH intermediate axle shaft.
  3. Remove the 6 lower splash shield bolts and the 2 pin-type retainers.
    • To install, tighten to 8 Nm (71 lb-in) .
  1. NOTE: The LH lower splash shield must be removed before the RH lower splash shield. Remove the lower splash shields.
118886165


  1. Remove the nut and position the bracket and wiring harness aside.
  2. Rotate the front end accessory drive tensioner counterclockwise and position the accessory drive belt aside.
  3. Position the generator B+ protective cover aside and remove the generator B+ terminal nut.
    • To install, tighten to 8 Nm (71 lb-in) .
  1. Disconnect the generator electrical connector.
  2. Remove the generator upper air duct bolt.
    • To install, tighten to 4 Nm (35 lb-in) .
  1. Loosen the 2 lower generator bolts and remove the generator upper air duct.
  2. Remove the pin-type retainer from the generator shield.
  3. Remove the bolt and the generator shield.
    • To install, tighten to 4 Nm (35 lb-in)
  1. Remove the generator stud nut.
    • To install, tighten to 47 Nm (35 lb-ft) .
  1. Remove the generator stud.
    • To install, tighten to 7 Nm (62 lb-in) .
  1. Remove the 2 generator bolts.
    • To install, tighten to 47 Nm (35 lb-ft) .
  1. Position the generator aside and remove the 3 generator lower air duct nuts.
    • To install, tighten to 4 Nm (35 lb-in) .
  1. Remove the generator lower air duct.
  2. Rotate the generator to gain enough clearance and remove it through the opening in the fender well.
  3. If necessary, remove the 2 generator bracket bolts and the generator bracket.
    • To install, tighten to 47 Nm (35 lb-ft) .
  1. To install, reverse the removal procedure.

Jul 19, 2010 | 2005 Mercury Mariner

1 Answer

96 f150 altenator rmovel instal


Section 14-02A: Generator, Integral Rear Mounted Regulator, Internal Fan Type, 95 Ampere and 130 Ampere 1996 Bronco/F-Series Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 05/18/2000 Generator, 5.0L, 5.8L, 7.3L Engines Removal
  1. Disconnect battery ground cable (14301).
  1. Disconnect electrical connectors from generator (GEN) (10346).
  1. Remove drive belt (8620).
  1. Remove generator retaining bolts (3).
  1. Remove generator.


    Generator


    j6040a.gif


    Item Part Number Description 1 — Fuel Filter Assembly
    (Part of 9K601) 2 19703 A/C Compressor 3 8146 Fan Shroud 4 10A313 Generator Bracket 5 10346 Generator 6 389706-S2 Generator Retaining Bolts (3) 7 — Heater Hose Clip 8 — Heater Hose A — Tighten to 21-29 Nm
    (16-21 Lb-Ft)
Installation
  1. Install generator.
  1. Install generator retaining bolts (3). Tighten bolts to 21-29 Nm (16-21 lb-ft).
  1. Install drive belt.
  1. Connect electrical connectors to generator.
  1. NOTE: When the battery (10655) has been disconnected and reconnected, some abnormal drive symptoms may occur while the powertrain control module (PCM) (12A650) relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 miles) or more to relearn the strategy.

    Connect battery ground cable.
2010&c18=modelyear&c35=wsm%2cgenerator%2c%205.0l%2c%205.8l%2c%207.3l%20engines%2cstj%2c14-02a%2cremoval%20and%20installation&s=1600x900&c=32&j=1.3&v=y&k=y&bw=1171&bh=491&ct=lan&hp=n&[aqe]

Apr 03, 2010 | 1996 Ford F150 Regular Cab

1 Answer

Alternator removal/ford taurus 1996


Generator Removal
  1. Disconnect the battery ground cable.
  2. Remove the accessory drive belt from the generator pulley.
  3. Remove the power steering line bracket and heater hose support bracket from the generator.
  4. Remove the upper generator bolts.
  5. Partially raise the vehicle on a hoist.
  6. Remove the right front wheel.
  7. Remove the lower fender splash shield retainers and position the shield out of the way.
  8. Remove the generator splash shield.
  9. Raise the vehicle.
  10. Disconnect the electrical connector and remove the battery positive cable from the generator.
  11. Position an adjustable stand to the subframe.
  12. Remove the right subframe bolts.
  13. Remove the lower generator bolt.
  14. Lower the subframe to provide clearance.
  15. Remove the generator
Generator — 3.0L (2V) and 3.0L (2V) FF Engines
  1. NOTE: The generator (GEN) (10300) is not internally serviceable.

    Disconnect battery ground cable (14301). Refer to .
  1. Disconnect the electrical connectors from the integral generator/voltage regulator.
  1. Loosen the generator pivot bolt. Remove the mounting brace bolt from the generator.
  1. Disengage the accessory drive belt (8620) from the generator pulley (10344).
  1. Remove generator brace.
  1. Remove the generator pivot bolt and generator/voltage regulator.

524109a.gif

Mar 01, 2010 | 1996 Ford Taurus

2 Answers

NEED TO REPLACE ALTERNATOR MYSELF ON MY NISSAN QUEST 1994 WHAT ARE THE STEPS


here's 96. should be the same. Be very careful not to overtighten any of the belts or you can break the snout off the crankshaft and ruin you engine.

Section 14-02: Generator, Integral Regulator — Internal Fan and Regulator Type 1996 Villager Workshop Manual
REMOVAL AND INSTALLATION Generator Removal
  1. Disconnect the battery ground cable (14301).
  1. Raise and support the vehicle.
  1. Remove the five engine and transmission splash shield bolts and two engine and transmission splash shield screws.




  1. Remove the RH engine and transmission splash shield (6775).
  1. Remove the wire harness bracket bolt.




  1. Remove the B-terminal insulator boot.
  1. Disconnect the generator electrical connector from the generator (GEN) (10346).
  1. Remove the ground wire nut from the generator and position the ground wire aside.
  1. Remove the B-terminal nut from the generator and position the B-terminal wire aside.




  1. Loosen the inner and outer generator-to-bracket bolts.


    61f4d2f.gif

  1. Loosen the generator locking bolt.



    93c9f65.gif
  1. Loosen the generator adjustment bolt.


    6e949fa.gif

  1. Remove the drive belt (8620) from the generator pulley (10344).
  1. Remove the generator locking bolt and washer.
  1. Remove the inner generator-to-bracket bolt and the two washers.
  1. Remove the outer generator-to-bracket bolt and the two washers.
  1. Remove the generator.
Installation
To install, reverse the removal procedure. Tighten the inner generator-to-bracket bolt to 23-26 Nm (17-19 lb-ft). Tighten the outer generator-to-bracket bolt to 23-26 Nm (17-19 lb-ft). Tighten the generator locking bolt to 16-20 Nm (12-15 lb-ft). Adjust the drive belt very carefully. Refer to Section 03-05 for the procedure.

Jun 05, 2009 | 1994 Nissan Quest

Not finding what you are looking for?
1995 Subaru Impreza Logo

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...