Question about 2000 Mercury Sable

Open Question

How to replace the headlight assembly on a 2000 Mercury sable

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 117 Answers

SOURCE: Mercury Villager headlight assembly diagaram for removal

it is a bit of a time consuming job it would be best to get a diagram to see where everything goes as this will help you alot otherwise take to a mechanic.
cheers
any feedback left would be great

Posted on Jul 01, 2008

  • 1 Answer

SOURCE: 2003 Mercury Sable headlight bulb replacement

This problem is now resolved, thanks to a prior post by sableowner.

http://www.fixya.com/cars/t1479995-2001_merc_sable_headlight_replacement

The 2003 Sable has the same headlight assembly and removal/replacement instructions as the 2001 Sable. Once I had this information in hand, bulb replacement was easy.

Posted on Jan 13, 2009

crayzeetrayn
  • 837 Answers

SOURCE: REPLACE HEADLIGHT ASSEMBLY IN 2000 LINCOLN TOWNCAR

Open the hood and make sure the car and the lights are off.
Remove the plastic protective cover.There are 3 knobs,turn halfway and pull.Put aside and out of the way.
Remove the three pins that are holding the light assembly in place.These are flat rods with a little bend at the end.
Twist and un-plug the lights,now you can remove the whole lens.
The light bulbs can also be removed and replaced from this point.
Make sure all the bulbs are working before you put it back together.

Posted on Mar 13, 2009

c17hydro
  • 2984 Answers

SOURCE: 2000 mercury sable drive belt

For VIN 2 FLEX Fuel:

4488d47.jpg For VIN U and S....with A/C:

c2b84a7.jpg PLEASE DON'T FORGET TO RATE!!!!

Posted on Apr 01, 2009

  • 1 Answer

SOURCE: 2000 MERCURY SABLE

My 2000 Sable starts blowing hot air about every 6 months. I mean like an oven. All I do is disconnect the battery negative terminal for about 5 minutes. After I re-connect the problem is solved. This solves many problems on this car, it just needs a re-boot. It must be powered by Microsoft (ha ha). Good luck. ps my auto headlamps never did work right either. Dave.

Posted on Apr 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Headlights, low beams work fine. when high beams are turned on, the left side goes out completely and there is no change to the right side.


Mercury Sable - YouTube

? 6:06
www.youtube.com/watch?v=Mlb1V5vNgFM
Jan 3, 2012 - Uploaded by 1A Auto Parts http://www.1aauto.com/1A/HeadLights/Mercury/Sable/1ALHP00223 ... Find out why. Close. How to Install Replace Headlight and Bulb Mercury Sable 00-05 ... How To Install Replace Fog Lightand Bulb 00-03 Mercury Sable

Oct 08, 2015 | 2005 Mercury Sable

1 Answer

How do I remove the headlight housing assembly for a 95 mercury sable wagon?


Then have clips on the back side that you have to spread apart and hold and then lift the side clip up and out of the adjusting screw.

Nov 06, 2013 | 1995 Mercury Sable

1 Answer

The headlight on the pass. side works right. the drivers side when in low beem, the light is in high beem. when the light is on high beem the light is on low beem. this is a 2000 mercury sable


someone has switched the wiring harness sockets to the wrong bulbs or installed the bulbs in reverse. get in behind the headlight assembly on the driver side and reverse the wires, if that does not work then pull the bulbs and swap them inside to outside and vice versa.

Jun 10, 2011 | Mercury Sable Cars & Trucks

1 Answer

TRYING TO GET MY WHOLE HEADLIGHT ASSEMBLY OUT TO CLEAN INSIDE OF HEADLIGHT ASSEMBLY. IT IS CAKED ON THE INSIDE WITH ****.


Cleaning this plastic is usually useless. You can replace it with used or new from aftermarket parts store. I believe this model has 2 clips you pull up on to remove the assembly. A haynes manual from the autozone will tell all usually.

Nov 16, 2010 | 1996 Mercury Sable

1 Answer

HOW TO FIX THE FRONT END OF MY 2000 MERCURY SABLE?WHAT PART WILL I NEED TO INSTALL THE HEAD LIGHTS?


Basic Socket Set
and undo the bolts, Unplug wire Remove headlight and replace.

Jun 22, 2010 | 2000 Mercury Sable

1 Answer

Dash illumination lights out on 2003 Mercury Sable ... How do I dis-assemble to replace lights ?


Dash illumination lights out on 2003 Mercury Sable ... How do I dis-assemble to replace lights ?

Oct 22, 2009 | 2003 Mercury Sable

1 Answer

2000 mercury sable drive belt


For VIN 2 FLEX Fuel:

4488d47.jpg For VIN U and S....with A/C:

c2b84a7.jpg PLEASE DON'T FORGET TO RATE!!!!

Apr 01, 2009 | 2000 Mercury Sable

1 Answer

2003 Mercury Sable headlight bulb replacement


This problem is now resolved, thanks to a prior post by sableowner.

http://www.fixya.com/cars/t1479995-2001_merc_sable_headlight_replacement

The 2003 Sable has the same headlight assembly and removal/replacement instructions as the 2001 Sable. Once I had this information in hand, bulb replacement was easy.

Jan 10, 2009 | 2003 Mercury Sable

Not finding what you are looking for?
2000 Mercury Sable Logo

Related Topics:

214 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

fordexpert

Level 3 Expert

5495 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...