Question about Chevrolet S 10

1 Answer

I have a s10chevey truck and it don't want to go in gear if i turn it off it will go in to geaR 1996

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 96 Answers

Sounds like the clutch master/slay cylinder is not moving enough or the engine is idled up too high

Posted on Jul 31, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My transmission will not shift out of first gear in my 96 sedan devill


Don't know

If the transaxle is from 1996, then a complete rebuilt
is the answer

If newer or been replaced & you have not driven at all
since you had any trans issues,a trans or repair shop is
all you can do

Nov 19, 2012 | Cars & Trucks

1 Answer

My gear shifter wont go into gears


Need a complete clutch service or at least the
slave hydraulic throw out brg assy

Oct 03, 2012 | 1996 Ford Probe

1 Answer

Changed cyl head, on 1996 2.2 toyota camry, cant seem to figure out cam timing


there is a hole in the camshaft gear turn the gear until it lines up with a mark in the cylinder head at the top. then line the crankshaft gear mark up with the mark on the block. sometimes the best way to see the camshaft timing mark is with a mirror.

Aug 16, 2011 | 1996 Toyota Camry

1 Answer

Trying to remove rear axle from 1996 chev. pickup 1500 4x4


you don`t say what if anything you have done so far or what the problem is your having.once the wheel and brake drum is off you will have to remove the differential cover(gear oil will come out),you will have to remove the spider gear lock pin from the gear carrier by finding the locking bolt that holds it in place.with this remove DO NOT TURN THE CARRIER GEAR ASSEMBLY or you will be re-installing spider gears and shims back in and must be installed in the proper place.then push the axle into the differential and you may the C clip fall if not remove the C clip to unlock the axle and pull the axle straight out without turning it as you pull.install in reverse order.

Jul 19, 2011 | 1996 Chevrolet K1500

2 Answers

Car whines when in reverse


You didn't say if it was an automatic or a manual transmission. If it is a manual, whine in reverse is normal because the reverse gear is straight cut. The forward gears are helical cut so they don't whine.

Jun 18, 2011 | 1996 Honda Civic

1 Answer

Car quits when put in gear


if the engine tick over is slower than 850rpm out of gear turn it up till it is about this high then put it in gear if the tick over fall low again tweek it back up, when in gear,,,,keep the brakes on hard if you are onder the bonet working on the tick over when in gear,,im told it hurts getting run over?

Nov 25, 2010 | 1996 Plymouth Voyager

1 Answer

Stuck in gear audi A4 1.9TD 1996


Check the trans gear oil!!!
Also the cables from the shifter to the trans actuate levers on the trans that sometimes stick. Check the levers.

Dec 09, 2009 | 1996 Audi A4

4 Answers

96 chevy blazer 3rd gear and overdrive slipping


i got a 1996 chev. blazer s-s10 4.3 engine 4x4.problem i got is i got 1st 2nd & overdrive & reverse but no 3rd gear what should i do

Jun 30, 2009 | 1996 Chevrolet Blazer

2 Answers

1996 Geo Metro Clutch won't disengage


Hi,

In all likelihood two (2) possibilities:
  • defective clutch cable (most likely); and/or
  • defective clutch fork (least likely).
Should it be the cable, this might be of help. It is turns out to be the fork, you might need the services of a qualified professional or a dealership.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information. Good luck and kind regards. Thank you for using FixYa.

Nov 10, 2008 | 1996 Geo Metro

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

107 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

70365 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...