Question about 2001 Ford Crown Victoria

3 Answers

No power to fuel pump on 1999 crown victoria - 2001 Ford Crown Victoria

Posted by on

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 593 Answers

Hello abzalkhan193
Heres a few things to check that could cut power to the fuel pump. The fuel pump inertia shutoff sw
in the trunk on the left side, there is a reset button on the switch if you push the button down and
you hear/feel a click then the switch was tripped and you just reset it. The switch's job is to cut off
the fuel in case of an accident. Next, the fuel pump fuse located in the battery fuse block under the
hood on the right fender well, fuse #1 20amp fuse. Next, the fuel pump relay, the relay is located in
relay center on the left fender well. Hope this is helpful.

Posted on Mar 11, 2011

  • falconeer82 Apr 06, 2011

    thanks for the tip, really aprreciate it....tiiits!

×

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 130 Answers

Ford has afuel pump reset check owners manual for location

Posted on Mar 11, 2011

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 55 Answers

If your not getting power to the fuel pump then you have a bad relay. If your getting power to your fuel pump and no start check the fuel safety switch in the trunk on the driver side. If all those check out ok the you have a fuel pump issue.

Posted on Sep 22, 2014

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 279 Answers

SOURCE: Where is the fuel pump shut off switch located on

The fuel pump inertia switch is located on the passenger side kick panel,Behind the plastic cover.

Posted on Jan 31, 2010

97crownvic
  • 28 Answers

SOURCE: crown victoria window motor replacement

remove the door panel. be very careful and make sure you get all the screws out. Should be maybe 2 on the bottom half of the door, and 2 on the top half. one is right by the handle, which is the one i forgot the first time i took my door pannel off. carefully pull the panel upward, and outward at the same time. Once the panel is off, disconnect the controls, and remove the light from the panel. Remove the plastic cover very carefully, it will tear, just keeps noise, and air, and the elements out.
There will be 3 screws, they are torx bolts, once you pull those 3 out. They are located middle of the door towards the right side. The motor will drop down a little bit. disconnect the wires for the motor, and wiggle the motor off of the regulator. the crown vics have a decent size hole to get into the door panel, you can also remove the speaker if that would help you do it. other than that, it just lining up the new motor into the car, pushing it into the regulator, and putting the 3 bolts in, make sure they are snug, and not cross threaded. put everything back together, and your set.

Posted on Mar 19, 2009

techbuster
  • 5081 Answers

SOURCE: How to Change a Fuel Pump in a 2001 Ford Crown

STEPS TO CHANGE FUEL PUMP

  1. Park the vehicle in a safe place and make sure there is enough room around the back of the vehicle for you to work and move tools around.
  2. Start the engine and let it idle while you relieve the fuel system pressure by removing the fuel pump fuse or relay from the fuse box. Wait a few seconds for the engine to stall, turn the ignition key off and replace the relay or fuse.
  3. Raise the back of your car using a floor jack and support it safely on jack stands.
  4. Disconnect the fuel tank filler pipe and the fuel pump connector located above the cross member underneath the vehicle.
  5. Disconnect the vapor tube from the tee connector on the right side of the car-passenger side-and the vapor line from the canister tube.
  6. Support the fuel tank with a jack and remove the nuts from the holding strap using a wrench or ratchet and socket. Move the strap away and lower the fuel tank. Discard the fuel tank mounting studs.
  7. Unplug the pressure transducer electrical connector located on the top rear corner of the fuel tank.
  8. Clean the area around the fuel pump mounting flange and remove the flange mounting bolts in a crisscross pattern.
  9. Lift the fuel pump assembly off the tank. Replace the new fuel pump in the assembly and install the assembly in the tank. Install the flange screws and torque to 89 inch lbs. (10Nm) using a crisscross pattern.
  10. Raise the fuel tank to its mounting position, install the strap using new mounting studs and torque the nuts to 26 foot lbs. (35 Nm).
  11. Connect the fuel pressure transducer electrical connector, vapor tube to the tee connector, vapor line to the canister tube, fuel tank filler pipe and fuel pump electrical connector.
  12. Lower the vehicle, start the engine and check for leaks.

Posted on Nov 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replaced fuel pump in my 99 ford crown Vic but still won't start


can you hear the fuel pump working if not check the wiring and power and ground by the tank. check fuel pressure, as if its low it won`t start, you can get bad new parts. do you have spark at the plugs. check for codes. just some places to start.

Apr 07, 2015 | 1999 Ford Crown Victoria

1 Answer

My 1999 crown vic is still not building fuel pressure. I've changed the fuel pump and fuel pump relay still not building enough pressure. What else can i try


check or replace fuel pressure regulator. symtoms are. lack of fuel pressure, excessive fuel pressure, black smoke and engine running rich, instant drop of fuel pressure, when turned off delay building back up sufficient fuel pressure. also be sure fuel filter is not plugged. check the filter first !!

Oct 24, 2011 | 1999 Ford Crown Victoria

1 Answer

I dont know which fuse controls my fuel pump on my 1999 ford crown vic


On fuse pannel it should say fuel pump. It should be near battery or inside car. Read owners manual for more detail.

Jun 10, 2011 | 1999 Ford Crown Victoria

1 Answer

How to replace fuel pump 1999 crown vic


Almost all vehicles made the last 30 years ,need to remove the fuel tank to get the sending unit and or fuel pump out. Can not believe the thousands of people with that question!

May 03, 2010 | 1999 Ford Crown Victoria

1 Answer

How to remove a fuel pump from a 99 crown victoria


first things first! disconnect battery! lift rear of car ! use jack stands ! just behind the rear AKA AXL DISCONNECT FUEL LINE WITH FOR TOOL ! HAMMER AND SCREW DRIVER look at the ring that holds the sender in to the tank! it only comes off one way! becareful ! fuel will pour out! once u have the sender out replace pump and reverse steps! if this helped please leave feed back!

Apr 16, 2010 | 1999 Ford Crown Victoria

1 Answer

Fuel pump is not pumping on my ford ltd crown victoria. i need a fuse diagram so i can see if it is just the fuse or if i need to replace the pump.


There is both a fuse and a relay for the fuel pumps electrical system. The image below of the Power Distribution Box is located in the engine compartment.

Fuse/Relay Location: 5
Fuse Amp Rating: 20 Amp Mini Fuse
Power Distribution Box Description: Fuel pump

Fuse/Relay Location: 203
Fuse Amp Rating: 1/2 ISO
Power Distribution Box Description: Fuel pump relay

eec14ad.jpg

Apr 14, 2009 | 2003 Ford Crown Victoria

1 Answer

94 CROWN VICTORIA FUEL PUMP


Yes you can replace it. It is in the fuel tank. You will need to drain the tank and remove it to gain access to the fuel pump. A floor jack will help when lowering the fuel tank. If you fo to a dealer to do this you will be looking probably around $700.00 to replace the pump.

Feb 17, 2009 | 1994 Ford Crown Victoria

1 Answer

1999 crown vic fuel pump location


fuel pumps in the gas tank are always mounted in the top of the tank

Feb 13, 2009 | 1999 Ford Crown Victoria

1 Answer

Crown Vic will turn over but not start


first do you hear your fuel pump running? if you don't more then likely the relay may have went bad. second check your connection to your coil's..make sure there clean and tight..and getting back to the fuel problem if you hear your pump running then it could be the fuel filter clog...try this and let me know....

Oct 13, 2008 | 1999 Ford Crown Victoria

Not finding what you are looking for?
2001 Ford Crown Victoria Logo

2,253 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...