Question about 2002 Cadillac Escalade

1 Answer

ABS system engage at low speed usually about within 5 to 10 miles per hour.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,608 Answers

There is either rust build up at the sensor where it bolt to the knuckle creating too much gap or there is a hair line crack in the reluctor ring which means you would have to replace the hub assembly.What you can do is remove the sensor where it connects to the knuckle and clean the surface area real good.and make sure all the rust is gone.Then drive the vehicle and see if it goes away.If not it is more than likely the hub bearing.The best way to tell which wheel it is is to use a scan tool.It will be one of the front wheels but you need to find out which one.What I do at work is drive in the parking lot with the scan tool and watch the speed sensors in the ABS data.When I feel it act up I look to see which sensor is dropping to zero speed and this tells me which wheel is the one causing the problem.Then I know to check for rust or ohm the sensor.If they check out good then I know it is the hub bearing assembly.Hope this helps.Good luck.Let me know if you have any more questions.

Posted on Mar 10, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cannot engage 4high on 2009 colorado


Supposed be moving when shifting into 4 low or 4 high, think it's a limit of 4 miles per hour, maybe a bit higher or lower speeds, owner's manual has instructions. Bad shift solenoid or relay? Has fuse/ relay checked out?

Feb 27, 2016 | 2009 Chevrolet Chevrolet Colorado LT

1 Answer

WHY DOES THE TCS LIGHT COME ON


Rear wheel sensor issue most likly the issue metal flakes on the sensor causeing the computer to think car is in a lost traction condition there fore retarding motor speed to slow car down to a safer speed to regain traction without applying brakes usuall need to remove sensor an clean with a soft bristle tooth brush to remove metal glakes on the speed sensor. Usually there are two on rear axle an two abs sensors in front both have to match rotation speeds if one sensor is off by a fraction it senses the car is hoing into a wheel spin condition or low inflation in one tire in the rear if pass sidebtire is low on air pressure it will throw of the amount of revolutions per min ratio left at 65 miles an hour 6300 rpm right side at recc air pressre 6500 rpm per min 200 rpm difference tricks computer your in a wheel spin
have sensors checked for metal debri or dirty sensor may have a broken wire or dirty

May 28, 2014 | 2002 Hyundai Santa Fe

2 Answers

2002 Ford Taurus abs engages on routine stops, brake pedal low and stopping distance seems greater.


Bad abs sensor you can pull the abs fuse under the hood usually large amp fuse 40-60 amp abs wont work put brakes will function better till repaired

Nov 16, 2012 | Ford Cars & Trucks

1 Answer

All gears are working, but once I reach 30 miles per hour the RPM's race without further acceleration


is this a three speed trans? or 4spd w/overdrive? either way i believe you have a pressure problem whether a torque converter or a trans pump. I was wondering how you know all gears worked if it will only do 30 mph as the 4th or overdrive usually wont engage at that speed. but here say,

Apr 03, 2011 | 1996 Chevrolet K1500

1 Answer

Will not go in 4 low 4x4 lights start blinking after trying . reset light by unhooking battery . then goes in 4 high normelly but not 4 low. i thlnk auto 4 is working 4 liter SOHC 1998


Normally 4 wheel drive HIGH is engaged on the fly or as you are moving more than 10 km per hour or 10 miles per hour but 4 wheel drive LOW is engaged at around 3 to 5 mph. no more or you could ruin the transfer case. Try going from 2 high to 4 high by switching back and forth and then try 2 high to 4 low when idling along. What usually happens is the mechanics under the car freeze up or rust up and you have to switch back and forth to free it up.

Nov 01, 2010 | 1998 Ford Explorer

1 Answer

Think i need to bleed abs system on ford expoler.


Sounds like the abs master cylinder area is in need of replacement if the abs fuse is removed and stops better.

Chattering can occur in an abs system when the system senses wheel lockup on that wheel and attempts to anti lock that wheel.

Could also be a wheel speed sensor not working, properly.

Hope this helps.

Jul 11, 2010 | 1997 Honda CR-V

1 Answer

Abs light, overdrive light comes on at the same time


ABS has got to do with the braking system while the overdrive is meant for activation of the auxilliary/ extra speed gear when driving over 60 miles per hour.

I will advice you run a scan on the car.

Good luck.

Dec 08, 2009 | 2001 Ford Windstar

1 Answer

I have a 2005 chevy equinox i replace the front rotors and brakes now when you come to a stop the car sounds like the abs system is kicking in


check the connections on the abs, behind the rotor by strut is the connection for the abs if the connector is loose or not properly affixed to the clip it sets off the abs trouble code or low speed saftey usually activates at slow speed under 5 miles an hour the connector and clip are part of the abs circuit--also recheck ur brake pads for binding and brake fluid level --if u get a trouble code have vehicle scanned some auo stores such as auto zone / advanced auto scan for free this will tell u which sensor or unit is causing problem

Oct 24, 2009 | 2005 Chevrolet Equinox

3 Answers

My abs. light comes on my renault megane whenever l get to 55 miles per hour.Have just changed both rear hubs and brake pads.Light goes off when l turn off the carand does not come on untill i get to 55mph...


Hi
I wonder if anyone can help me.
I just changed my rear disks and brake pads on my Renault Megane 1.6 53 reg and all is good but now my ABS light is on and the service light is on. I think its normal because of the changes but now how do i reset the service light and the ABS light to go off?

Oct 22, 2009 | 2003 Renault 181

1 Answer

Abs sensor


there is more than likely a piece of rust stuck to one of the front abs wheel speed sensors. this happens during brake service sometimes.

Dec 13, 2008 | 2003 Ford E250

Not finding what you are looking for?
2002 Cadillac Escalade Logo

191 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...