Question about 2002 Chrysler Sebring

3 Answers

2003 Chrysler Sebring fan speed switch has four speeds total. Blower motor only operates on high. What do I check?

Posted by on

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

You need to replace the blower motor resistor...

Posted on Jul 11, 2009

  • Hildy Jan 16, 2013

    i bought the resistor but how do i get the glove box out....'04 Sebring convertible?

×

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 4 Answers

If your ac only operates on high and you never hear the ac blow air on any other setting, than start by checking and replacing your blower motor. Should be in the dash, check your manual on where its located. in mine ( little older sebring) its a pain to get to, but worth it when the ac works on any fan speed.

Posted on Aug 01, 2008

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

I had the same problem in my 2002 Sebring. I went to a website for chrysler and It is a common problem with the Sebring. I changed the control unit but it did not work. Then I changed the resistor and wala...It works fine in all 4 speeds. The resistor is behind the glove box by the blower. Disconnect the electrical plug-in and remove the two bolts. Put in the new resistor. I got mine from a junkyard for 15. New the go for 25 or so.

Posted on Aug 14, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Heater won`t work at 1,2,3 settings, it only works on #4 setting (chrysler,sebring 2003)


sounds like a blower resistor. usually it is on the passenger side under dash near blower motor and hvac box. the resistor add resistance to the circuit to slow the blower motor, if it is inop then you only get high speed.

Dec 30, 2012 | 2003 Chrysler Sebring

1 Answer

Air condition blower switch works only on high on my 2000 chrysler sebring jxi


You most likely need a blower motor resistor it reduces the amount of voltage to blower motor but is by passed on high speed

Aug 08, 2011 | 2000 Chrysler Sebring

2 Answers

Heater blower only works on high


REPLACE THE CONTROL SWITCH PANEL

Mar 29, 2011 | 2003 Chrysler Sebring

1 Answer

Switch on a/c only works in the 4th position, not on 1,2 or 3


Sounds like you have a bad blower motor resistor. The resistor is located near the blower motor under the passenger side of the dash. The resistor uses a series of resistors to drop voltage which makes the blower run at different speeds. High speed bypasses the resistors and allows full voltage to the blower motor.

For more info click the link below
http://www.fixya.com/cars/r6571076-blower_motor_not_work

Feb 08, 2011 | 2003 Chrysler Sebring

1 Answer

My 2001 Voyager blower fan only runs on high.


This is 100% the Blower (Fan) Motor Resistor located near the Blower Motor.
This is a very common problem with Chyrsler, Dodge, Plymouth. The key symptom is the Fan only working on High.
This is very easy to access and replace.

Let me know if this helped....

May 11, 2010 | 1999 Chrysler Sebring

2 Answers

Fan heater just blow in high, not in low speed.How can I fix it?


it is your blower resistor.It is mounted by your blower motor.

Feb 07, 2010 | 1999 Chrysler Sebring

2 Answers

Climate control switch only works on high


There is a resistor switch that controls the fan speeds. When it shorts out it defaults to high speed only. It is not too expensive and is not very hard to replace. It is located adjacent to the blower and has an electrical hook up to it.

Hope this helps.

Sep 30, 2009 | 2001 Chrysler Voyager

1 Answer

Heater fan only works on high speed


usually when the blower motor gets old its starts to draw more current to run. which can pop fuses, burn out resistors and melt wires. also when you go to replace the resistor check the connector for signs of melting or burning you may end up having to replace that conector

Jan 06, 2009 | 1999 Chrysler Sebring

1 Answer

My blower only works on high


Several possiblities here first look at the switch and see if the resisters are messed up on it.

Second, could be a relay under the dash that has went out.

Not likely that the motor has failed due to the high speed fan option, so you can rule that out.

I don't think that 01 had any computer control on their fan speed during that year, but might be possiblity.

Aug 20, 2008 | 2001 Chrysler Sebring

Not finding what you are looking for?
2002 Chrysler Sebring Logo

1,603 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...