Question about 1998 Volvo V70

1 Answer

Head how do I r&r cylinder head on a V70 T? do I have to pull the engine out of the car?

Posted by on

  • stephenfh12 Aug 26, 2008

    thanks for trying, but the reply has come a little late. The head has been off and valves replaced and all is well.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 102 Answers

No it can be done in the car but when you back off the head bolts one turn soke them over night with PB blaster before removing then or else

Posted on Aug 26, 2008

2 Suggested Answers

consaka
  • 661 Answers

SOURCE: I can install an engine cylinder head from a 99

I dont see why not. Go for it.

Posted on Mar 09, 2010

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Water in the oil


Radiator coolant in the engine oil is normally an indication of a failed cylinder head gasket or a crack in the cylinder head or both.

Running the engine in an overheated condition will cause head gasket failure and often a crack in the cylinder head.

The problem you have is coolant is escaping into the engine's lubrication passages via the failed head gasket or head crack and contaminating the engine oil. If not fixed you will cause further damage to the engine as oil contaminated with radiator coolant cannot adequately lubricate the engine.

Running a leak down test on each cylinder will confirm the leak. In this case you are going to need to have the cylinder head removed and thoroughly checked for cracks and any warpage as well as a new cylinder head gasket fitted. The condition the engine block surface will also need to be checked.

Jun 14, 2016 | Cars & Trucks

1 Answer

Need the head bolt torque specs for 2001 Volvo v70 to replace heads


need more info of the car, engin sice and is it petrol or diesel

Jul 24, 2014 | 2001 Volvo V70

2 Answers

I have no compression in cylinder 1 it has only 15 pd of pressure but it doesn't smoke


Do a cylinder leak down test

Still nothing ,the valves are worn,head comes off

Compression does not tell you if a valve seals properly,
only how much pressure your building at cranking speed

Jul 23, 2014 | Cars & Trucks

1 Answer

Water in oil


Water in the oil is most likely a head gasket leak-blown head gasket. You will have to pull the cylinder head off and replace the head gasket. If it's a V6 or V8 engine, a compression test will tell you which bank of the engine has the head gasket problem. One cylinder or two cylinders next to each other will have low compression.

May 23, 2012 | 1985 Chevrolet Chevy

1 Answer

Ironfist109, do you also havecthe cylinder head sequence and toruque numbers, all for an 1998 volvo. Thanks your diagams were great


  • This head is torqued in three stages. Start at 1 and go to 12 each step in a row.
  • 15 foot lbs.
  • 44 foot lbs.
  • + 130 degree all the way around as well.



ironfist109_385.jpg



Regards, Tony

Oct 12, 2011 | 1998 Volvo V70

1 Answer

Engine oil level rise from normal and oil colour change and engine doesnt start whats the remedy?


You have a leaking engine cylinder head gasket, coolant is getting into the oil. Pull the cylinder head off and have it checked for being warped and if OK replace the cylinder head gasket.

Mar 04, 2011 | 2008 Ford Fusion

1 Answer

Correct pressure for torque the head of mazda pickup 1998


Since you didn't say which engine you have, I've pulled torque specs for 3 different engines. Also, since I can't include a diagram showing the relative locations of the numbered head-bolt locations, it would be a good idea for you to purchase a vehicle specific repair guide that will show this info.


Take particular note about the TTY (Torque to Yield) bolts used on 2 of the 3 engines shown. It is said that new head bolts MUST BE USED when head is replaced or re-installed to obtain the proper torque.



B2500 4 Cylinder

Torque sequence: --------- ' 10 6 2 4 8 ' front ' ' ' 7 3 1 5 9 ' -----------Step 1: torque in sequence to 51 Ft/Lbs Step 2: torque again in sequence to 51 Ft/Lbs Step 3: final tighten all bolts an additional 90 to 100 degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.







B3000 3.0 6 Cylinder

Torque sequence ---------- ' 6 4 2 8 ' ' ' ' 5 1 3 7 ' ---------- Step 1: torque to 59 Ft/Lbs Step 2: loosen in sequence (1) full turn Step 3: torque to 41 Ft/Lbs Step 4: torque to 73 Ft/Lbs









B4000 4.0 6 Cylinder

Torque sequence --------- ' 5 1 3 7 ' ' ' ' 6 4 2 8 ' --------- Step 1: torque cylinder head bolts in sequence to 26 Ft/Lbs Step 2: torque cylinder head bolts to 56 Ft/Lbs Step 3: turn cylinder head bolts in sequence an additional 90-degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.


Good luck with this job!

Feb 06, 2011 | 1998 Mazda Pickup

2 Answers

My car is not firing right,


when your engine breaks a timing belt it bends one or more valves in the engine cylinder head, that is the problem, u have bent valves.

Apr 09, 2009 | 2000 Hyundai Accent

Not finding what you are looking for?
1998 Volvo V70 Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

yadayada
yadayada

Level 3 Expert

63801 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Mark Jones

Level 2 Expert

76 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...