Question about 1994 Isuzu Rodeo

1 Answer

94 rodeo ute

Been sitting for 2 years with very little petrol had the fuel pump changed over and the man said there was good presure when i drive it seems to chug along intill the revs get higher the not bad would it be moisture in the take or slug or the injectores

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

Get it into a garage that does the fuel system flushes . shop around try to get one of the ones that are more common at a reputable garage . as always avoid dealer when possible but always try to buy oem parts

Posted on Aug 01, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rodeo petrol starts but wont rev


Holden Rodeo 1989 2.6mpi , start and only runs for 2 or so seconds themselves stalls, after putting on a fuel peesure gauge, fuel looked okay and slowly dropping, found the ECM relay was intermittently switching on and off, gave it a tap and the engine kept on running, relay not repairable, replace with new part. Located in the fuse and relay box on the right hand side of engine bay next to battery. Hope this helps.

May 24, 2012 | Holden Rodeo Cars & Trucks

1 Answer

It had been sitting for a year with bad timing chain . We changed that and it ran good for 2 day then it started bactkfiring now it want idle and has no power . When you start it it runs then bogs down...


well if it ran for two days then its something stupid like a blocked fuel filter on the bottom of the fuel pump caused by stale petrol ,which is what happens after a year of sitting

Dec 19, 2010 | 1987 Toyota Pickup

1 Answer

I have a 1996 holden rodeo ute petrol and it wont idle


I had the same problem, I changed everything, air flow meter, plugs, leads, checked the timming belt etc. etc. The problem turned out to be the fuel pump, its inside the tank, you need to check the fuel pressure with an inline guage, it needs to have 30 psi, mine was only 15 psi. also you should have the injectors cleaned. good luck. Gary

Oct 18, 2010 | Isuzu Rodeo Cars & Trucks

1 Answer

Fuel problem holden rodeo ute 1994 is not starting beleave it could be the fuel pump. Remove line no fuel coming out belreave that the pump is beside fuel tank drivers side of vehicle


In that year of vehicle I wouldn't be surprised if the fuel pump was in the tank. I would be surprised if it was not in the fuel tank.

Jul 05, 2010 | 1994 Isuzu Rodeo

2 Answers

1993 rodeo not running no power to fuel pump


if there is no power to the fuel pump check relays and fuses....UNDERHOOD FUSE & RELAY PANEL IDENTIFICATION Fig. 2: Underhood Fuse & Relay Panel Identification Courtesy of ISUZU MOTOR CO. Fusible Link Identification ? A - 80 Amp (1991-92 3.1L) ? A - 60 Amp Main-1 ? B - 30 Amp Main-2 ? C - 30 Amp (1993-94) ECM (3.2L) ? D - 30 Amp Condenser Fan (A/T Models) Relay Identification ? 1 - Headlight Relay ? 2 - A/C - Heater Relay ? 3 - Starter Relay ? 4 - A/C Compressor Relay ? 5 - Charge Relay ? 6 - Fuel Pump Relay ? 7 - ECM Relay ? 8 - Wiper Relay Fuse & Circuit Breaker Identification ? 1 - 15 Amp (1991) ECM, Fuel Injection System ? 1 - 15 Amp (1992-94 2.6L) ECM, Fuel Injection System ? 1 - 10 Amp (1992-94 3.1 & 3.2L) Heated Oxygen Sensor, Fuel Injection System ? 2 - 20 Amp (1991-92) Fuel Pump ? 2 - 20 Amp (1993-94 2.6L) Fuel Pump ? 2 - 15 Amp (1993-94 3.2L) Fuel Pump ? 3 - 10 Amp (1991) ? 3 - 15 Amp (1992-94) Turn Signal Lights, Hazard Warning Flasher Lights ? 4 - 10 Amp Horn, Door Locks ? 5 - Not Used (1991 3.1L) ? 5 - 10 Amp Charging System, Charge Warning Light WARNING: Always disconnect battery ground cable before servicing "high- current fuses. It is recommended that "high-current" fuses be replaced by a qualified technician. Page 1 of 2 FUSES & CIRCUIT BREAKERS -1994 Isuzu Rodeo LS? 6 - Not Used (1991) (1992-93 2.6L) ? 6 - 10 Amp (1992-94 3.1L & 3.2L) A/T Interlock System ? 6 - 10 Amp (1994 2.6L) Heated Oxygen Sensor, Fuel Injection System ? 7 - 20 Amp Heater/Air Conditioning Blower Controls ? 8 - 10 Amp Air Conditioner Compressor Controls ? 9 - 10 Amp Right Headlight ? 10 - 10 Amp Left Headlight © 2008 Mitchell Repair Information Co., LLC.
62217_isuzfuse_1.jpg
Underhood fuse block swap out relay #7 thats the ECM relay.
Ground Circuits Using a DVOM, touch negative voltmeter lead to a good ground. Touch positive voltmeter lead to each ground terminal. With vehicle running, voltmeter should indicate less than one volt. If reading is greater than one volt, check for open, corrosion and loose connection on ground lead. See ECM GROUND LOCATION table for ECM ground location.
Page 1 of 1 SYSTEM/COMPONENT TESTS - 2.6L EFI -1994 Isuzu Rodeo

Mar 28, 2010 | 1993 Isuzu Rodeo

4 Answers

My 2003 rodeo sometimes will idle erradicly and stall is this a computer issue or just dirty petrol


I have reviewed your problem and have the fallowing for you to aces.
I have had 2- Rodeo's first was a 4 cylinder, and the one I am driving now is a 4 wheel drive 6 cylinder.
Both have given me problems with engine stalling and rough idling.
I have also found problems with the check engine light.

Things I have found to cure problems.
First, after 75 or 80K, you will need to change and service several things.
(1) EGR sensor, this unit sits to the rear left side of engine and will greatly contribute to poor idling and a computer, check engine light from time to time. This unit cost about $95.00 and autozone will warranty for life. The unit is easy to remove and replace, it has 2- bolts and a 4 or 6 wire plastic connector on it top.
(2) You fuel filter, this unit is located under the drivers side door and is also easy to remove and replace. Cost about $15.00.
(3) Last, fuel pump, now my last Rodeo had bad fuel and I had to replace the pump and that is a job and a half.
The fuel pump is located in the fuel tank and the tank will have to be dropped, to replace it.
I was able to pick up a used pump at a local junk yard, because of the price and availability. You may have to buy from dealer.
Hope this information has been of good help to you.
Have fun. P.S. My first Rodeo blew up after 227K and the one I am driving now has over 140K.
Please rate....

Nov 09, 2009 | 2003 Isuzu Rodeo

2 Answers

Adjusting fuel pump


If you have the 91 3.1 V6 Rodeo you can't adjust the fuel pump or fuel pressure. The only thing you can really do is to get a throttle body rebuild kit that will have a new diaphragm for the fuel pressure regulator. If you want to adjust it, you'll have to get an aftermarket regulator and install on the return line (the smaller line) and remove the spring out of the regulator on the throttle body. If you feel the fuel pressure is too low, then you might need to change the pump. Its located in the fuel tank, only takes 1 or 2 hours to do.

Jul 12, 2009 | 1991 Isuzu Rodeo

2 Answers

2004 V6 3.5 Rodeo


"when the fuel pump kicks....it makes a very short duration sound....you can hear it....but in seconds it will be gone......as gasoline has made its way to the engine.........

if you cant hear any noise from the fuel pump......it could be that the fuel pump realy is bad........if you happen to change the relay....and it still does not work.....then it is the fuel pump. that is fried.......

about the water.....i am not shure......unless there was water in the gasoline itself....or somebody put water in there in purpose....

hope this helps...

May 16, 2009 | 2004 Isuzu Rodeo

1 Answer

Holden 94 rodeo petrol


Good Day
Vale clearance cold
intake .006 in (.15 mm)
exhaust .010 in (.25 mm)

Timing
1. With transmission in Neutral or park, start engine and warm to normal operating temp. turn eng,and all accessories off. connect Tachometer. Connect timing light to no 1 spark plug wire.

2. Disconnect and plug fuel vapor canister purge hose and EGR vacuum hose. Start and ensure idle is 900 RPM. adjust idle as required. Check ignition timing ( 12 @ 900)

3. If adjustment is required, loosen distributor hold down bolt and turn until timing is within specification. Tighten distributor hold down bolt and recheck timing. adjust idle speed as required.

hope this helps

Cheers

Aug 18, 2008 | 1994 Isuzu Rodeo

Not finding what you are looking for?
1994 Isuzu Rodeo Logo

Related Topics:

124 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...