Question about 2007 Dodge Charger SRT8 Sedan

1 Answer

Electrical Failure of many features.

I recently jacked up one whole side of my 2007 Charger R/T up so that the wheels were off the ground about 4 inched, frontand back of the same side of the car, to istall a undercar lighting. After righting the car, the BAS/ESP warning light stayed lit, the turn signals, horn, high beams, and wiper blades don't work. Is the a sensor that has to be reset from lifting both wheels of the same side of the car so that it was on resting on only the two wheels on the oppposite side? How do I fix this? Is it a main fuse? Is there a common plug the affects all of these? The engine does starts, no problems there.
Thanxz......Jeff

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 56 Answers

Well, for starters if your car has a stabling system on it, you can check your owners manual for jacking the car to see if it tells you to turn off a switch and where the switch is and you can reset it by turning it off and then back on again and starting the car, it will then relevel the car.... lincoln has this on their vehicles, switch is supposed to be turned off before jacking the car ever. If there is no switch, then dealer needs to see the car. As for the lighting, it sounds like you might have cut or spliced into the wiring system for your lights. I would start by checking the fuse for those lights and seeing if its blown and replacing it. If it is the fuse, and you replace it and it blows again, you definately hooked up your wires wrong...maybe put a ground wire to a hot wire which will blow the fuse... if you can't find the problem, take the car to the dealer, it's under warranty still I am sure.

Posted on Oct 13, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to tell if 4wheel drive is working on a 1998 chevy blazer


Depends on the system.
It is impossible to drive a true 4 wheel drive vehicle on the road due to wind-up between the axles so first a unidirectional clutch was fitted into the front drive to prevent wind-up but the main problem of one wheel losing traction and the whole vehicle becoming stuck remained.

Over the decades differential locks and/or limited slip differentials have been fitted to overcome the basic problems.

In more modern times refinements, often to cut costs, such as viscous couplings have been used to produce automatic or part time 4 wheel drive vehicles and the development of abs and later more powerful computers added traction control systems.

Jacking each wheel in turn from the ground should reveal whether drive is being transmitted to it. When there is a centre differential lock or it is of the limited slip variety, using a jack with good wheels and on smooth ground lift first the front and then the rear and attempt to drive. If it is working in each case the vehicle will move and should roll the jack along the floor.

The front and rear differential locks can be tested in a similar fashion but 3 wheels will need to be raised.

Nov 14, 2017 | 1998 Chevrolet Blazer

1 Answer

2003 chevy astro van w/AWD. AWD is not working at all.


what was your test to determine the failure ?
if you jacked up one end and the car didn't drive off the jacks , that is how an all wheel drive works
It has a differential in the transmission that allows the front axle to drive at different speeds to the rear ( same as one wheel on the axle will go faster than the other when going around corners)
it is used to prevent torque wind up in the drive train and destroying transmissions , diffs and drive lines
it has to have all 4 wheels on the ground so that the 3rd diff is not operational unless going over a speed bump or dips in the road
however if you have a 4 wheel lock for the transmission, that is different as it locks up the 3rd diff in the transmission making the car a 4 x 4

Dec 03, 2016 | Cars & Trucks

1 Answer

How do i replace a transmission control solenoid and where is it located?


Which control solenoid ? There are a few ,1-2 shift , TCC solenoid ,3-4 shift ,PWM solenoid .
Remove the case side cover. Refer to Case Side Cover Replacement (W/ Gasket) .
Removal Procedure
Tools Required J 28467-360 Engine Support Fixture
  1. Disconnect the negative battery cable. Refer to
  2. Caution: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before servicing any electrical component. Disconnect the negative battery cable to prevent an electrical spark should a tool or equipment come in contact with an exposed electrical terminal. Failure to follow these precautions may result in personal injury and/or damage to the vehicle or its components.
    in General Information.
  3. Remove the park/neutral position switch. Refer to PNP Switch Replacement
  4. Install the J 28467-360
  5. Raise the vehicle. Support the vehicle. Refer to Vehicle Lifting and Jacking in General Information.
  6. Remove the left front tire and wheel assembly. Refer to Wheel Removal in Suspension.
  7. Remove the inner splash shield.
  8. Remove the tie rod end from the knuckle assembly. Refer to Strut Assembly in Suspension.
  9. Remove the stabilizer shaft link from the lower control arm. Refer to Control Arm in Suspension.
  10. Remove the ball joint from the steering knuckle. Refer to Ball Joint in Suspension.
  11. Remove the drive axle from the transmission. Refer to Drive Axle in Driveline/Axle.
  12. Remove the pinch bolt from the steering gear intermediate shaft. Refer to Intermediate Steering Shaft in Suspension.
  13. Caution: Failure to disconnect the intermediate shaft from the rack and pinion steering gear stub shaft can result in damage to the steering gear or to the intermediate shaft. This damage may cause loss of steering control, which could result in an accident and possible personal injury.
  14. Remove the intermediate shaft from the steering gear. Refer to Intermediate Steering Shaft in Suspension.
  15. Position a transmission jack under the transmission oil pan. Raise the jack until lit supports the transmission.
  16. Remove the three frame-to-body bolts on the left side.
  17. Lower the transmission jack and the transmission in order to gain access to the case side cover.
  18. Remove the oil cooler pipes at the case. Refer to Automatic Transmission Oil Cooler Pipes Replacement
This is a monumental task , suggest you take your vehicle to AAMCO or some other transmission shop .

May 09, 2016 | 1996 Oldsmobile 88

3 Answers

I have heavy vibraton in front end starting at 30mph up to 65mph. pulld t right


check tyres for failure
check for disc rotor failure ( warped or broken)
check for wheel bearing failure

Mar 06, 2015 | 2004 Chevrolet TrailBlazer

1 Answer

Electrical failure


the ground in my headlight connector got hot ,melted, and the headlight quit, a couple 3M disconnects fixed it right up

Apr 05, 2014 | 2007 Chevrolet Malibu SS Sedan New Cars

1 Answer

99 ford f150 4wd won't engage, clicks but does not engage


Without knowing how the 4X4 works you don't have much chance of finding the problem , (tapping on stuff ) ? There is an electronic control module that makes this system work . Could have DTC'S - diagnostic trouble code's stored in the (GEM)
Transfer Case -Electronic Shift on the Fly (ESOF) Operation The electronic shift on the fly (ESOF) system is an electronic shift 4x4 system that allows the operator to choose between two different 4x4 modes as well as 2-wheel drive. The operator can switch between 2WD and 4H mode at speeds up to 88 km/h (55 mph). To engage or disengage 4L range, the vehicle speed must be less than 5 km/h (3 mph), the brake pedal depressed, and the transmission must be in NEUTRAL.
The transfer case is equipped with an electromagnetic clutch which is located inside the case. This clutch is used to spin up the front driveline when shifting from 2WD to 4H mode at speed. When the control switch on the instrument panel is turned, the generic electronic module (GEM) recognizes that a shift has been requested and activates the electromagnetic clutch and the relays which power the transfer case shift motor. When the shift motor reaches the desired position, as determined by the contact plate position inputs to the GEM, power to the shift relays and motors will be removed. When the transfer case front and rear output shafts are synchronized, the spring loaded lockup collar mechanically engages the mainshaft hub to the drive sprocket. Finally, the front axle collar is engaged and the electromagnetic clutch is deactivated.
Shifts between 2WD and 4H can be made at any speed up to 88 km/h (55 mph). Listed below are the inputs and outputs needed by the GEM to execute a change between any of these modes.
Feature Inputs:
  • 4WD mode switch (various resistances; go to Table 1).
  • Contact plate position inputs A, B, C, D (grounded when closed, open circuit when open; go to Table 4).
Feature Outputs:
  • 4x4 shift motor relay outputs (go to Table 2).
  • Transfer case clutch relay (grounded when relay is activated, open circuit when relay is deactivated).
  • 4x2/4x4 vacuum solenoid (grounded when activated, open circuit when deactivated).
  • Cluster indicators (ground when activated, open circuit when deactivated).
When shifting into or out of 4L, the GEM requires that the vehicle speed be less than 5 km/h (3 mph), the brake is applied, and the transmission is in NEUTRAL.

Feature Inputs:
  • 4WD Mode Switch (various resistances; go to Table 1).
  • Contact Plate Position Inputs A, B, C, D (grounded when closed, open circuit when open; go to Table 4).
  • Output Speed Shaft (OSS) Sensor (Sinusoid Signal: 0.7V-20V, 2.2 Hz/mph).
  • Brake Input (battery voltage when brake is depressed, open circuit when not activated).
  • Transmission Range Sensor (grounded when transmission is in NEUTRAL, open circuit otherwise).
  • Start/Clutch Depressed Input (go to Table 3).
Feature Outputs:
  • 4x4 Shift Motor Relay Outputs (go to Table 2).
  • 4x2/4x4 Vacuum Solenoid (grounded when activated, open circuit when deactivated).
  • Cluster Indicators (grounded when activated, open circuit when deactivated).
  • P1804 Transmission 4-Wheel Drive High Indicator Circuit Failure GEM REFER to Section 413-01A . P1806 Transmission 4-Wheel Drive High Indicator Short Circuit to Battery GEM REFER to Section 413-01A . P1812 Transmission 4-Wheel Drive Mode Select Circuit Failure GEM REFER to the Symptom Chart. P1815 Transmission 4-Wheel Drive Mode Select Short Circuit to Ground GEM REFER to the Symptom Chart. P1820 Transmission Transfer Case Clockwise Shift Relay Coil Circuit Failure GEM GO to Pinpoint Test A . P1822 Transmission Transfer Case Clockwise Shift Relay Coil Short Circuit to Battery GEM GO to Pinpoint Test A . P1824 Transmission 4-Wheel Drive Clutch Relay Circuit Failure GEM GO to Pinpoint Test E . P1826 Transmission 4-Wheel Drive Low Clutch Relay Short Circuit to Battery GEM GO to Pinpoint Test E . P1828 Transmission Transfer Case Counter Clockwise Shift Relay Coil Circuit Failure GEM GO to Pinpoint Test A . P1830 Transmission Transfer Case Counter Clockwise Shift Relay Coil Short Circuit to Battery GEM GO to Pinpoint Test A . P1832 Transmission Transfer Case Differential Lock-Up Solenoid Circuit Failure GEM GO to Pinpoint Test C . P1834 Transmission Transfer Case Differential Lock-Up Solenoid Short Circuit to Battery GEM GO to Pinpoint Test C . P1838 Transmission Transfer Case Shift Motor Circuit Failure GEM REFER to the Symptom Chart. P1846 Transmission Transfer Case Contact Plate 'A' Circuit Failure GEM REFER to the Symptom Chart. P1850 Transmission Transfer Case Contact Plate 'B' Circuit Failure GEM REFER to the Symptom Chart. P1854 Transmission Transfer Case Contact Plate 'C' Circuit Failure GEM REFER to the Symptom Chart. P1858 Transmission Transfer Case Contact Plate 'D' Circuit Failure GEM REFER to the Symptom Chart. P1866 Transmission Transfer Case System Concern - Servicing Required GEM REFER to the Symptom Chart. P1867 Transmission Transfer Case Contact Plate General Circuit Failure GEM REFER to the Symptom Chart. P1876 Transmission Transfer Case 2-Wheel Drive Solenoid Circuit Failure GEM GO to Pinpoint Test C . P1877 Transmission Transfer Case 2-Wheel Drive Solenoid Circuit Short to Battery GEM GO to Pinpoint Test C . P1891 Transmission Transfer Case Contact Plate Ground Return Open Circuit GEM REFER to the Symptom Chart. Your best bet , take it to a qualified repair shop. Tapping on thing's isn't the way to diagnose

Jan 10, 2018 | Cars & Trucks

1 Answer

How to check rear wheel bearings 2007 jeep compass


block front wheels and jack up rear slightly off the ground, keeping your body parts out of harms way you can grab and shake tires, if they move back and forth or in and out even slightly it is time for bearing work

Nov 23, 2012 | 2007 Jeep Compass 2.4

1 Answer

Replace brake pads on 2007 vw polo


Park the polo on level ground, turn the engine off and apply the parking brake. Pull the hood release handle and move to the front of the car.

Lift the hood and remove the master cylinder. Remove one-half of the brake fluid inside the reservoir with a syringe.

Loosen the lug nuts on the rear wheels with a tire iron. Place the jack beneath the frame at the back of the Volkswagen and lift the back tires off the ground. Rest the rear axles of the Volkswagen on two jack stands. Remove the lug nuts and take the rear wheels off.

Reach behind the brake caliper to locate the caliper mounting pins. Remove the pins with a 12 mm socket and ratchet. Lift the caliper from the brake rotor and suspend it above the wheel assembly with a bungee cord or wire coat hanger.

Remove the rear brake pads from the slots in the caliper bridge. Inspect the caliper bridge and rotor for damage and significant wear. Replace the rotor if it is warped or badly scored. Scoring of the rotors can lead to break failure and will prematurely wear the new brake pads. Place new brake pads into the slots of the caliper bridge.

Attach the piston depression tool to the caliper. The tool will fit over the back side of the caliper and against the piston inside. Twist the tool's handle to force the piston into the side of the rear caliper. Remove the tool once the caliper piston is totally depressed within the caliper.

Replace the caliper onto the caliper bridge and screw in the caliber mounting pens by hand. Replace the rear wheel onto the wheel bolt and screw on the lug nuts.

Repeat the process for the other side of the rear of the polo. Lift the rear end of the vehicle with the jack and remove the jack stands. Lower the rear tires to the ground and tighten the lug nuts with a lug wrench.

Return to the engine compartment. Remove the master cylinder cap and check the level of brake fluid. Place a funnel into the container and fill the reservoir with brake fluid as needed.

Oct 23, 2010 | Volkswagen Polo Cars & Trucks

1 Answer

How do you replace the headlight bulb in a 2007 bmw 328i?


You have to remove the bumper first...

Tools Required:
- socket wrench/socket kit
- 8mm socket
- 10mm socket
- flathead screwdriver
- flathead stubby
- torx driver set

Optional Tools:
- car jack
- monkey (to hold your work lights)

Instructions:
- jack up car (optional)
- At least jack up one side of the car

1) Remove 4 screws on top of bumper ( under hood, above kidney grills)
2) Remove 2 screws in each wheel-well, and clip bumper trim away from wheel-well trim
3)Push wheel-well trim away so you can unfasten 2 screws inside that hold top part of bumper to the car on each side
4) Release about 7 Screws on bottom of bumper from underneath
5) Remove bumper by uncliping each side and then pulling bumper forward

Foglights will stay in place. simply disconnect the cable.

After you remove the bumper and unplug the Foglights
1) To remove the lights you also need to remove the bracket that hold the lights
2) Remove the blots on the bracket and top of headlight.

Installation is in the reverse of removal...

Oct 21, 2010 | 2007 BMW 328xi Sports Wagon

1 Answer

How do u chage tire on a 2007 bmw 650i


block wheel on opposing side to avoid rolling.loosen lug bolts on wheel using lug wrench. donot completely remove nuts. place jack at designated position on side of car. diagram should be on spare cover in trunk under carpet along with the appropriate tools.raise vehicle with jack just high enough to clear ground. remove nuts and flat tire and replace with spare. tightened lug nuts and lower jack. check nuts again for tightness.

Apr 26, 2010 | 2007 BMW 650i Convertible

Not finding what you are looking for?
2007 Dodge Charger SRT8 Sedan Logo

162 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...