Question about 1996 Chevrolet Blazer

2 Answers

Turn Signal Flasher

I need to replace my flasher for my turn signals (not the hazard lights, they're still working). I can't find the flasher. It's not in the fuse box or behind the glove box. Where is it?!

Posted by on

  • 3 more comments 
  • Anonymous Dec 04, 2008

    is this the same on a 92 s10 blazer 2wd?

  • scaryy17 Mar 29, 2009

    I have kind the same problem because the fuse is good same the light so it must be the signal flasher, but I don't know where is located, I hace a chevy blazer 96

  • Anonymous Mar 15, 2014

    turn left signal not working only hazard flasher on

  • Anonymous Mar 23, 2014

    Turn signal replace for b2200 1989

  • Anonymous Apr 01, 2014

    Find flashers

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 335 Answers

Turn Signal Flasher - 58940048Its behind the center of the dash under the Ashtray U need TORX screwdrivers to take out the screws got to take off nearly all over the under dash plastic trim.
Contact me if you need more help Thanks

Posted on Jul 31, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,056 Answers

You didn't specify if it was an S10 Blazer or a K5 Blazer

On the S10 Blazer, it's below the radio. You have to remove a panel to get to it.

Posted on Jul 31, 2008

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The hazard back lights wont quit blinking when car is running even when i pull the fuse on a 2002 buick regal


What fuse are you pulling ?

Hazard Lamps
The hazard warning switch is part of the turn signal switch. The turn signal switch receives battery voltage at all times through the HAZARD SWITCH Fuse. When the hazard switch is placed in the HAZARD position, battery voltage is applied to the hazard lamp/turn signal lamp flasher. The hazard lamp/turn signal lamp flasher sends a turn signal flasher signal to the turn signal switch. The turn signal switch provides all of the turn lamps and turn indicators with the turn signal flasher signal, simultaneously flashing them on and off.

Turn Signal Lamps
The front turn signal lamps are made up of the front park/turn signal lamps and rear turn signal lamps. The front turn signal lamps flash with the rear turn signal lamps when a turn is initiated using the turn signal/multifunction lever. The turn signals will operate only with the ignition switch in the RUN position and will not operate during hazard flasher operation.
When the ignition is turned to the RUN position, battery voltage is supplied to the TURN SIGNAL Fuse. Battery voltage is then applied through the turn signal fuse circuit to the turn signal switch. When the turn signal switch is placed in the LH or RH position, voltage is supplied to the hazard lamp/turn signal lamp flasher. The hazard lamp/turn signal lamp flasher supplies a turn signal flasher signal to the turn signal switch. With the turn signal switch in the LH or RH position the corresponding turn signal indicator, rear turn signal, and front turn signal receive the turn signal switch signal and will flash. The front turn signals receive the turn signal switch signal from the turn signal switch via the BCM. The turn lamps are permanently grounded.

Replace the turn signal switch. Refer to Multifunction, Turn Signal, and Hazard Switch Replacement - On Vehicle in Steering Wheel and Column - Tilt.

Feb 11, 2017 | Buick Cars & Trucks

2 Answers

Turn singles and hazards are not working on my 2001 deville


I would replace the turn signal hazard combo switch.

Nov 28, 2016 | Cars & Trucks

1 Answer

1985 LeSabre flashers work turn signals don't need location of turn signal switch or are they one of the same


You mean turn signal flasher? No, the hazard flasher and turn flasher on older cars were separate. Often, the hazard flasher was right of the steering column (under the dash), and the turn flasher was left of the column. Look for two similar canisters. Turn the hazard lights on and locate the hazard flasher by feel or hearing. The turn flasher will be the other one. They both may be retained by metal clips.

Sep 16, 2015 | Cars & Trucks

1 Answer

TROUBLESHOOT TURN SIGNAL


try the hazard lights. if they work check the bulbs with them working. if good and the turn signals not working then it could be the signal flasher is bad. witch out the hazard flasher for the signal flasher it they work then replace flasher, or the turn signal switch it bad.

Sep 05, 2015 | Cars & Trucks

1 Answer

Turn lights blink with hazards but not with turn signal..flasher replaced. is It the multifunction lever then??


There should be a turn signal flasher and a hazard flasher. They are two different parts. If you replaced the hazard flasher and not the turn signal flasher than I would start by replacing the turn signal flasher.

One thing you can do once you find the turn signal flasher is to unplug it and use a jumper wire between the two pins of the connector then turn the key to the run position and place the turn signal lever in the left or right position. If the turn signal lights know light up than the turn signal flasher is the problem

Sep 09, 2014 | 1997 Oldsmobile Cutlass Supreme

1 Answer

How to fix turn signal on 86 Chevy Astro Van


you don`t say but do the lights work either on the front/back on both sides.if not then it may be a fuse that needs replacing or need a bulb replacement.if the lights work but don`t flash then it sounds like a signal flasher problem.the flasher is located in the fuse panel under the dash on the drivers side.if the hazard flashers work then turn them on to find the hazard flasher by the fuse panel then you will know what the signal flasher looks like and change the signal flasher.make sure you change the one for the signals and not the hazard one.if the hazards work then i would say the signal switch is good as the hazards work through the same switch.

Apr 21, 2011 | Chevrolet Astro Cars & Trucks

1 Answer

Turn signals were working...but blinking fast. now they don't work at all...replaced fuse in side panel near door and still nothing. Everything else works..headlights, wipers, hazards..what gives?


you have a separate flasher for the turn signals.this is what your problem sounds like.if all your lights are working including the signal indicator on the dash then it will be the signal flasher.if you turn on the hazard flashers and locate it under the dash, this will show you what the turn signal flasher will look like.then you will have to look for the flasher unit on the fuse panel that looks like the hazard flasher.replace the turn signal flasher and you will have your signal flashers again

Mar 08, 2011 | 1996 Dodge Ram 1500 Club Cab

1 Answer

When the blinker is flipped up or down on the column the tail lights dont respond. But the brake lights and the hazards still work fine. Whats the problem?


The turn signal flasher relay may have a problem.Turn on the hazards and follow the clicking sound to the source and usually the hazard flasher and turn signal flasher are very close to each other.Remove the one that is clicking and put it in place of the turn signal flasher.If the Turn signals then work you will need to purchase a new turn signal flasher relay.They are usually just a few dollars.

Jul 29, 2010 | 1986 Ford F 250

3 Answers

Hazard flashers do not work. Turn signals do. Changed relay. Nothing. Ugh. 1992 oldsmobile cutlass supreme


You changed the hazard flasher or the turn signal flasher? It has two, one for the hazard and one for the turn signals

Aug 31, 2009 | 1992 Oldsmobile Cutlass Supreme

1 Answer

Turn signals dont work at all


Try your hazard lights. If they work, then it's your turn signal flasher. With your hazards on, listen under the dash for the constant "clicking". Locate the flasher for your hazrads... the turn signal flasher should be near it. Once you find it, just pull it out and replace.

You can use your hazard flasher in place of your turn signal flasher, just swap the two. This will get you to the store to buy a replacement.

Jun 08, 2009 | 2005 Hyundai Accent

Not finding what you are looking for?
1996 Chevrolet Blazer Logo

832 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...