Question about 1993 Nissan Pathfinder

1 Answer

1992 pathfinder switched motors but when i put it all back together it is so tight that you cant even turn the motor by hand

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I'VE GOT A vg30e for my 93 pathy,

i had the same problem. it turns out the main bearings for the front are slightly larger then the middle ones i didnt notice and put them in wrong

once u look at them it may seem obvious

hope that helps

Posted on Aug 02, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

My 1992 la sabre heater fan dont work. It works when I hot wire from the battery. where exactly is the fuse for this? I cant find it

The fuse panel is in the motor compartment under the hood on the left hand side at the back.

Here's a video.

Dec 27, 2014 | 1992 Buick LeSabre

1 Answer

I replaced the clutch which required the motor to be removed. After making the repairs and putting everything back together, the car want crank

Make sure that the battery is charged and good. Clean the battery cables. Make sure you have the positive cable connected to the positive red battery cable and the other end to the starter. Make sure negative cable is connected and tight. Check if you can turn the engine over by hand with a socket on the crank shaft that the motor isn't tight. Make sure all wires are connected to proper terminals and connections. If this doesn't help repost and I will try to help with more solutions

Apr 06, 2014 | 2006 Chevrolet Cobalt

1 Answer

01 Mazda 626 I4 not starting after overheat/head gasket replacement

I would almost have to be there in person to advise.
I doubt anything happened to the starter as a result of the engine overheating.
One of the pistons or cylinder walls could have warped when it overheated which would cause a difficult crank, but you should have noticed it when you turned it by hand.
Its possible the timing is off, even possible something broke after you got it all back together.
I would probably start by pulling the plugs and making sure it is not a compression problem. Also try turning the crank by hand to see if the engine is tight.

Dec 24, 2012 | 2001 Mazda 626

1 Answer

1992 pathfinder heater fan level connections

No this year and model have problems with the motor that drives the blower, check the connector at the blower motor, see if they are burnt looking.

Jan 20, 2012 | 1992 Nissan Pathfinder

1 Answer

My 1991 nissan pathfinder's wiper motor repair

The cowl panel has to be removed. You will find plastic clips and possibly a few screws holding the panel on. Once you remove the panel you will see the wiper linkage and motor.

Contact us at and we can e-mail an image to you. Thanks

Jan 20, 2010 | 1991 Nissan Pathfinder

1 Answer

Will a toyota motor run if the wires are not connected to alt

No the engine should turn over,and run.You may have a ground off the motor,or the battery has gone down.Also look for a main fuse that is blown,check all fuses,it may even be a max fuse,it is a large fuse in physical size.

Sep 06, 2009 | 1992 Toyota Corolla

1 Answer

Tranny/motor connectivity

there is a nipple on the converter that must meet up with a indent in the middle of the flywheel you need to have some help and one of you spin the torque converter and gently rock the moter in to place it will worki have done this several times on the rangers 

May 14, 2009 | 2002 Ford Ranger Regular Cab

1 Answer

3.0L tranny wont properly mount to motor

Did you make sure the torq converter was all the way into the trans. pump? sounds to me it was not, and i hope for your sake you did not break the ears on the pump. Unbolt the trans. unbolt the torqconverter from the flexplate and spin the converter untill it drops back in the pump keep spinning until it drops in a good inch and then you got it.

Apr 19, 2009 | 2002 Ford Ranger Regular Cab

1 Answer

Need to replace positive battery cable

ok disconect the old one complety from the battery FIRST then the starter motor, on your new positve put you conectors on then connect to the starter motor FIRST then to you battery make sure there all tight then your ready to go

Jun 08, 2008 | 1987 Nissan Pathfinder

Not finding what you are looking for?
1993 Nissan Pathfinder Logo

Related Topics:

107 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts


Level 3 Expert

78289 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides