Question about 2004 Dodge Neon

1 Answer

Programming keyless remote for Neon 2004

Need help programming a remote bought on ebay for Dodge Neon 2004.Inever had an original remote as car was bought w/out one .I also haveEquus code reader/scanner if needed. Thanks

Posted by on

  • 2 more comments 
  • Anonymous Aug 13, 2008

    I have the same problem. The keyless remote I bought on E-Bay, said it would work for all 2004 Dodge Neon SXT models. Does the car have to be preprogrammed for keyless entry?

  • gosuperbeego May 01, 2009

    Thanks for the info, although after following these instructions I still can't seem to get my extra remotes to progrewm. I get al the way to the chime that indicates it's in programing mode but do not get a chime ffom any of the remotes when a button is pressed. Not even the origonal programed remote. Although IT still woriks. I even replaced all the batterys. Any Ideas? I'm thinking the maximum of four remotes may have been programed with a previous owner.

  • Anonymous Mar 12, 2014

    I bought a remote off ebay for the 502 astro start remote start but don't know how to program it , help plz

  • Anonymous Mar 14, 2014

    2004 dodge neon coda reader said gear 1 incorrect

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 46 Answers

There is a way to program a remote if there is already a valid remote. Unfortunatly if you don't have a valid remote the only way to get one programmed is at the dealership with their scan tool.

I have pasted directions for programming a remote if there is already a valid transmiter.


CUSTOMER PROGRAMMING For a customer to be able to program RKE transmitters themselves, at least one RKE transmitter must be programmed already. This procedure is to add additional transmitters. If all transmitters are lost, the DRB III® scan tool must be used to program the new transmitters.

  1. Insert the key into the ignition switch, and turn the ignition switch to the RUN position without starting the vehicle (allow chimes to stop).
  2. Using the RKE transmitter programmed to the RKE module, press and continuously hold down the UNLOCK button for 4-10 seconds.
  3. Within the 4-10 second time range, continue to hold the UNLOCK button and press the PANIC button. Both buttons may then be released. Upon the PANIC button being depressed, the message for customer programming mode will be transmitted to the RKE module.
  4. A chime will be heard to verify that the customer programming mode has been entered (allow 3 seconds to hear chimes).
  5. Press and release any button on each transmitter that is to be programmed to the RKE module, including any transmitters which were previously programmed to the RKE module (with a maximum of four possible). After each transmitter is successfully programmed, a chime will be heard to verify that successful programming of the transmitter has occurred.
  6. After thirty seconds, or upon the ignition switch being turned OFF, the RKE module will exit programming mode.

Posted on Aug 30, 2008

  • joshua
    joshua Jun 24, 2014

    i changed the batteries in my remote and tried programming to my neon but i never get the car to chime at me. is there a way to tell if my car is suppose to have a keyless entry function. the fuse panel on the side of the dash has a fuse in the keyless remote spot and its not blown. help please i don't want to spend $60 on getting a locksmith.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is there a way to reset keyless entry for 04 endeavor?


Search Results

    2004 Mitsubishi Endeavor Key Fob Remote Programming ...

    blog.keylessentryremotefob.com/.../04/2004-mitsubishi-endeavor-key-fo...
    Apr 25, 2013 - 2004 Mitsubishi Endeavor Key Fob Remote Programming Instructions ... you might have visit us at Keylessentryremotefob.com You can also ...

    Mitsubishi - Free Keyless Remote Fob Entry programming .

    How To Replace Mitsubishi Endeavor Key Fob Battery 2004 ...

    ? 2:04
    www.youtube.com/watch?v=yeQRdre7O0Q
    Oct 31, 2014 - Uploaded by Keyless Entry Remote Inc
    ... will show you How To Replace Mitsubishi Endeavor Key Fob Battery 2004 2005 To Order This Remote ...

Nov 01, 2015 | Cars & Trucks

1 Answer

2001 GMC Safari - keyless remote programming help needed


You need to return the remote to midwest keyless and either tell them to give you a remote with the exact part number or buy one off of ebay. They are about $60 from the dealer. When the doors lock and unlock, the computer is telling you that the brain is now in learning mode but it is a must to have the correct remote. I have programmed thousands of keyless remotes so please believe what I say. You can program up to 4 remotes for one car but they all must be programmed at the same time. If you buy one remote and program it then get a second remote at a later date, you need to program both simultaneously. If you just program the second remote, the computer will no longer recognize the first remote. That is just some extra information for you. Let me know if you need any more help.

May 21, 2010 | 2001 GMC Safari

1 Answer

Keyless remote stopped working, I replaced battery


The 1997 to 2003 Dodge Caravan and Grand Caravan use a standard key and remote setup with a separate remote fob. However, the 2004 to 2009 Dodge Caravan and Grand Caravan use a combination key and remote on one device. To program a new keyless entry remote for the 1997 to 2003 Dodge Caravan, you must have at least one functional remote, which is required to enter synchronization mode. To program the combination key for the 2004 to 2009 Dodge Caravan, you must have two functional combination keys. If you do not, you'll need to see an authorized Dodge dealer for keyless entry programming assistance.


2004 to 2009 Caravan Programming Instructions
  1. Insert one of your working combination keys into the ignition. Turn it to "On"; leave it in this position for about 10 seconds but no longer than 15 seconds. Turn it to "Off" and remove it.
  2. Insert your second working combination key into the ignition within 15 seconds of removing the previous key. Turn it to "On". After 10 seconds, you'll hear a chime and the "Theft" light will begin to flash, entering synchronization mode. Turn the key to "Off" and remove it.
  3. Insert the combination key you want to program. Turn it to "On." After 10 seconds, you'll hear a chime; then the "Theft" light will turn off. When the light turns off, the combination key--including the key and the remote--is programmed.
  4. Repeat Step Three for each combination key you want to program. A total of eight can be programmed.
Hope this help (remember comment and rated).


May 08, 2010 | 2008 Dodge Grand Caravan

2 Answers

Programming the keyless remote


if you have the original remote, you can do it yourself. My remote was working without a problem until the other day when all of a sudden it didn't work out of nowhere. I thought it was the battery (might have been and needed to be reprogrammed after replacing it) so I changed it. Still didn't work. So I did a search and found the following instructions: Click Here

The answer is remarkably simple:
1. Get in the car and close the door.
2. Turn the key to the ACC position
3. Push the unlock button on the remote until the blinkers flash once.
4. Get out of the car and test the remote. It should be working fine. ( I actually was able to test it while in the car)

P.S. I would change the battery first.

Apr 29, 2010 | 2004 Hyundai Tiburon

1 Answer

2004 ram remote keyless entry


The instructions are in the owner manual on how to manually program it.

Jul 07, 2009 | 2004 Dodge Ram 1500

2 Answers

Unable to program my keyless remote for 2000 chevy malibu


take key fob to a cparts store , most have a tester on the counter

Jun 08, 2009 | 2000 Chevrolet Malibu

1 Answer

Programming a keyless remote for a 1998 Plymouth Breeze


Most eBay sellers that deal with key fobs will provide programming instructions...ask the seller before you buy from them.

Mar 31, 2009 | 1998 Plymouth Breeze

1 Answer

Need of programming instructions for keyless entry for 1996 LHS


System operation
System will automatically lock all doors when vehicle is driven in excess of 15 mph
Pressing UNLOCK (on remote) once deactivates system and unlocks driver door only
Pressing UNLOCK (on remote) twice w/in 5 seconds deactivates system and unlocks all doors
Alarm/central locking functions can be altered using remote transmitter


Programming

Access data link connector (DLC)- druvers sude fascia
Switch ignition on
Jump DLC terminal 1 and ground
Ensure doors lock and unlock, indicating programming mode active
Press any button of each remote to be programmed
Ensure doors lock and unlock after each remote operation - indicating programming complete
Remove jump lead to exit programmming code

A maximum of two remotes can be programmed

Jan 20, 2009 | 1997 Chrysler LHS

1 Answer

2000 dodge neon alarm


This is what i found but you need one fob.

here is another way if you can get it done( i bevlieve) There is a box under the dash of your can it says keyless entry if you have the right box and the fab just plug and play.

Make sure you get the screws in the defrost vent there is some screws and then it there is snaps


http://shopping.msn.com/specs/keyless-entry-remote-fob-clicker-for-2004-dodge-neon-with-do-it-yourself-programming-requires-1-wor/itemid1124228415/?itemtext=itemname:keyless-entry-remote-fob-clicker-for-2004-dodge-neon-with-do-it-yourself-programming-requires-1-wor

Nov 15, 2008 | 2002 Dodge Neon

2 Answers

06 mazda3 keyless remote programming instructions


It should be hit the unlock button 3 times, open and close the door 3 times, the locks will operate themselves twice. Hit the unlock button on the remote and it should program. you should try a remote from the dealer not from ebay.

Sep 20, 2008 | 2006 Mazda MazdaSpeed

Not finding what you are looking for?
2004 Dodge Neon Logo

1,758 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

70365 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...