Question about 1995 Nissan Pickup

2 Answers

I have a 1995 nissan pickup, 4 cylinder. Does the starter come out from the top right or below the truck on the right. I can't seem to get my hands on the bolts.

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

The starter has to be removed from the top through the right side of the engine. Removing the bracket holding the gas filter allows enough room for the starter and solenoid to pass through the opening. I had to use a 14 mm wrench instead of a socket to remove the bolts as there is no room for the socket wrench even with extensions.

Posted on Jul 31, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

It is a VERY tight fit, but you have to get to the top bolt from the top underneath the intake manifold. The bottom one is axcessed from underneath the starter. Mine has an automatic and the starter came out the bottom right. Once you have it loose from the engine then you can remove the wiring.Now the tricky part, you have to rotate the starter until it will drop through the hole between the frame and tortion bar,expect it to come out nose first or tail first( can't remember), there will be a small bracket on the frame that will be in your way, hack saw. It just takes some patience but it will come out. Good Luck.

Posted on Aug 14, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the starter relay located on a 1997 nissan hard body pickup


Hi Eddie,Here's a link to a Nissan part site,the starter relay is 25224G.If you look at the truck picture,it has letter's,find letter G AND THAT'S WHERE THE STARTER RELAY IS,BY THE WAY,i HAVE A MINT 85 nISSAN 720 4X4,HERE'S A VIDEO OF IT,TAKE CARE. Parts found for 1996 Nissan Hardbody Pickup 1995 1997 Body Electrical Relay CHECK MINE OUT. 85 Nissan 720 4x4 2 4 Weber conversion

Jul 09, 2015 | Nissan Cars & Trucks

1 Answer

How do I replace starter from 1995 Nissan


The basic starter replacement is simple.
1. disconnect the negative battery cable.
2. remove the starter mounting bolts
3. remove the starter
4. disconnect the cables from the starter.

Dec 08, 2014 | 1995 Nissan Pickup

1 Answer

Removing starter nissan pick up 4 cylinder engine


Okay , i will give you step by step, the book calls for .9 for time.
1) First remove the front right tire.
2) Remove neg battery terminal.
3) Remove starter wiring.
4) Remove the right front splash shield.
5) Remove the exhaust manifold heat shield.
6) Remove the exhaust manifold.
7) Remove the oil filter.
8) Remove the oil sender connector.
9) Remove the starter bolts and remove starter from cylinder head side.

Hope this helps, let me know how it goes, good day.

Dec 24, 2012 | 1991 Nissan Pickup

1 Answer

Where is the starter in a 1995 nissan pathfinder


Nissan Pick-ups and Pathfinder 1989-1995
Starter - REMOVAL & INSTALLATION
(see Figures 1 and 2)
  1. Disconnect the negative battery cable at the battery, then disconnect the positive battery cable at the starter.
4178adf.jpg


Fig. 1: Starter removal on 4WD-6-cylinder engine

74f3669.jpg

Fig. 2: Starter removal on 2WD-6-cylinder engine
  1. On 4wd models with the 6-cylinder engine:
    1. Remove the front gravel shield.
    2. Detach the oil pressure switch connector.
    3. Drain the engine oil and remove the oil filter.
CAUTION The EPA warns that prolonged contact with used engine oil may cause a number of skin disorders, including cancer! You should make every effort to minimize your exposure to used engine oil. Protective gloves should be worn when changing the oil. Wash your hands and any other exposed skin areas as soon as possible after exposure to used engine oil. Soap and water, or waterless hand cleaner should be used.
  1. On 2wd models with the 6-cylinder engine:
    1. Remove the front right wheel.
    2. Remove the front gravel shield.
    3. Remove the exhaust manifold heat insulator.
    4. Remove the exhaust manifold.
    5. Detach the oil pressure switch connector.

  2. Unfasten the remaining electrical connections at the starter solenoid.
  3. Remove the two nuts holding the starter to the bell housing, then pull the starter toward the front of the vehicle and out.

Hope this help (remember rated this).

May 18, 2010 | 1995 Nissan Pathfinder

1 Answer

Distibuter cap and firing order


I do not know if you have the 2.4L (4-Cyl) or the 3.0L V6; however I have included both below.

For the 2.4L DOHC In-Line 4-Cylinder:
Firing Order:
1-3-4-2
Cylinders:
(back)
...4
...3
...2
...1
(front)
Distributor:
.....(+)
3..........1
......O.....
4..........2
.....(+)

For the 3.0L V-6
Firing Order:
1-2-3-4-5-6
Cylinders:
....(back)
5.............6
3.............4
1.............2
....(front)
Distributor:
......6
1..........5
2..........4
......3

Apr 04, 2010 | 1995 Nissan Pickup

1 Answer

How do I remove/install a starter on 1996 nissan


this is pretty cut and dry, remove neg battery terminal, raise vehicle if needed, remove the wiring from the back of starter, then remove the two starter mounting bolts and pull starter out, to install reverse directions, good luck.

Mar 06, 2010 | 1996 Nissan Pickup

3 Answers

1995 nissan pickup 4 cylinder timing chain - 256k miles


Most definetly yes. It should run you around 500 dollars. If you timing belt breaks it will destroy your valves and head.

Dec 30, 2009 | 1995 Nissan Pickup

1 Answer

Best Method to Replace Starter on 1993 Pickup


According to the online manual at AutoZone, you need to remove the right front wheel, the front gravel shield, the exhaust manifold heat insulator, the exhaust manifold, and detach the oil pressure switch connector. The picture shows lifting the starter out from the top once it is unbolted.

I've changed the starter on a '95 with a 4 cylinder engine, and the top bolt was a bugger to get to, requiring two extensions and a universal on my ratchet set. Good luck!

Mar 09, 2009 | 1993 Nissan King Cab

1 Answer

Putting on a starter


According to the manual, it's pretty straightforward. Disconnect the ground cable from the battery. Then remove all wires connected to the starter/solenoid -- one heavy wire from the battery, and one or two smaller wires. Then remove the bolts which attach the starter to the engine. The starter is at the right side of the engine at the rear.

Installation is the reverse of the above. Make sure you have all wires attached and tight before you reconnect the battery ground cable.

Jul 12, 2008 | 1995 Nissan Pickup

Not finding what you are looking for?
1995 Nissan Pickup Logo

169 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...