Question about Ford F-100

1 Answer

Removing calipers from 1973 ford f-100 - F-100 Ford Cars & Trucks

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Send me $12.95 and I'll tellya.

Posted on Jul 31, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

How do I replace a water pump on a 1973 Ford E-100 van

there are 6 bolts that remove the entire front grill assembly hradlights and all the bolts are located on each side of the seam where the fender meet the front grill once removed the water pump and all are easy to get to it is all open and easy to work on

Jun 21, 2014 | Ford Cars & Trucks

1 Answer

1973 ford pickup I beam rubber grommet

here is a picture that i labeled to help you figure out the ones that you need. i hope this helps ~ Zach

May 21, 2014 | 1981 Ford F 100

1 Answer

Why do all brakes on my 1973 corvette lock up after using for a few minutes

Brake hoses are deteriorated on the inside and swelled shut. Unlikely you have 4 bad calipers.

May 19, 2014 | 1973 Chevrolet Corvette

1 Answer

1973 ford f-100 making noise as i drive,and quits when i take off the gas

What kind of noise is it making? Almost sounds like a vacuum leak. Need more info.

Apr 03, 2013 | Cars & Trucks

1 Answer

Removing coolant lines... rusted

Try heating up the stuck threaded collar with a propane torch it should loosen up after it gets hot.

Jun 12, 2012 | Ford Mustang Cars & Trucks

1 Answer

I have a 82 ford f 100 and the front pads won't

Do they have spring clips holding them fast to the caliper. Just pry them off the caliper with a screwdriver. The outer pad that rests against the caliper piston bore also has a clip underneath going into the bore. It is also just pulled out. Maybe a little rust is holding yours tighter than normal? You do have the caliper bolts removed, and the caliper free from the rotor, only held to vehicle by the brake line, right?
Good luck.

Jan 29, 2012 | 1981 Ford F 100

1 Answer

My 1973 ford f100 will idle rough at lower rpm's

This can be a vacuujm leak or a cylinder missing.

Aug 10, 2011 | 1981 Ford F 100

1 Answer

Need instructions to remove the front rotor on F250 Four wheel drive truck - 2001 year

  1. Raise and support the vehicle; Remove the wheel and tire assembly;
  2. After removing the tire, remove the brake pads;
  3. Remove the disc brake caliper by removing the two disc brake caliper pin bolts. Lift the disc brake caliper from the disc brake caliper anchor plate (2B292). If necessary, remove the V-springs.
  4. Remove the pads. Remove the front disc brake caliper anchor plate stainless steel rail clips.
  5. Remove the rotor.
  6. Note: Perform this step for DRW vehicles. Remove the eight hub extender nuts, the hub plate and the rotor. Remove the eight hub plate nuts. Remove the hub plate. Remove the rotor.

Mar 02, 2011 | 2001 Ford F250 Super Duty Super Cab

3 Answers

How much does it cost to replace brake liners for a 1999 ford escort

Front or rear or both? How much if you did it yourself or if you had a shop do it?

Mar 30, 2010 | 2000 Ford Escort

1 Answer

Problems with front brakes on 1980 F-100

its common for older calipers to lock up. try cleaning the slides and lubing them. also when the calipers are off make sure the piston moves by depressing it all the way in. then drive again.

also very rare but you could have a bad brake hose causing pressure to stay inbetween the colapsed hose and caliper. this will keep a slight pressure on the side with a bad hose. but not so common like i said.. checking a bad hose by removing hose from caliper side. fluid should continue to flow out. if nothing flows out after 2 or 3 minutes you have a resriction somewhere. then remove hose from the hard line to see if fluid flows from the brake line. if fluid flows from brake line you have a bad hose. if fluid still does not flow from brake line you have other issues before the brake line. could be bad master.check master the saem way you check hose hopefully its easy. GOOD LUCK

ASE certified
plz rate

Feb 09, 2009 | 1981 Ford F 100

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

5655 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides