Question about Pontiac Safari

1 Answer

Windshield wipers won't work, motor seems to be ok. how can I tell if the problem is in the switch on the column, the circuit board on the wiper motor, or somewhere else?

Posted by on

  • Anonymous Sep 06, 2008

    yes

  • makmaki Oct 23, 2008

    I have the same problem. Front Windshield wipers work only sometimes and never when it rains. Back one works just fine. 1992 Pontiac Transport. In



×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Have a 96 chev cavalier changed wiper motor power at motor still wont work fuse is good

Posted on May 06, 2011

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 701 Answers

SOURCE: wheres the circuit board for a windshield wiper

Hello jlwhelchel: My name is Roger and I will answer your question. Raise the hood locate the wiper motor. Remove the cover held on by three screws. Remove the cover. The cover is the module.
Should you need further help please just ask. Please rate the answer. This way I know the information was helpful. Thank You for using Fix Ya. Roger

Posted on Oct 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wipers in up position in off. 94 lincoln town car. How do the wipers return to rest position?


Do you know how to do electrical testing ?
PINPOINT TEST E: WINDSHIELD WIPERS WILL NOT PARK AT PROPER POSITION E1 CHECK WIPER MOTOR GROUND
  • Disconnect connector from windshield wiper motor.
  • Check continuity to ground at Circuit 57 (BK).
Is ground OK? Yes No GO to E2 . SERVICE open in Circuit 57 (BK). RESTORE vehicle. RETEST system. E2 CHECK FOR POWER AT WIPER MOTOR
  • Place ignition switch at RUN and multi-function switch at OFF.
  • Check for battery voltage between Pin 1, Circuit 65 (DG) and Pin 4, Circuit 57 (BK) at the windshield wiper motor connector.
Is B+ present? Yes No GO to E3 . SERVICE open circuits. RESTORE vehicle. RETEST system. E3 CHECK MOTOR CIRCUIT CONTINUITY THROUGH WINDSHIELD WIPER CONTROL MODULE
  • With multi-function switch at OFF, check continuity between Circuit 28 (BK/PK) and 56 (DB/O) and between Circuits 61 (Y/R) and 63 (R).
Is continuity OK? Yes No GO to E5 . GO to E4 . E4 CHECK CIRCUITS TO WIPER CONTROL MODULE
  • Disconnect wiper control module connector.
  • Check continuity of Circuits according to the chart below from the wiper motor to the wiper control module.

    Wiper Control Module Connector Wiper Motor Connector Pin Circuit Pin 6 Pin 2 28 (BK/PK) Pin 8 Pin 6 56 (DB/O) Pin 12 Pin 5 61 (Y/R) Pin 13 Pin 3 63 (R)
Is continuity present? Yes No REPLACE wiper control module. RESTORE vehicle. RETEST system. SERVICE open circuits. RESTORE vehicle. RETEST system. E5 CHECK WIPER MOUNTING ARM/PIVOT SHAFT
  • Check that windshield wiper mounting arm and pivot shaft and linkage is not bent, cracked or mis-positioned.
Is windshield wiper mounting arm and pivot shaft linkage OK? Yes No REPLACE windshield wiper motor. RESTORE vehicle. RETEST system.

Nov 14, 2016 | 1994 Lincoln Town Car

1 Answer

Wipers stop in the middle of my wishield,will not park properly


Sorry , no adjustment .
Wiper/Washer System Components
The Wiper / Washer System consists of the following components:
• Windshield wiper / washer switch
• Windshield wiper system module / motor
• Windshield washer fluid pump
• Windshield washer fluid level switch
• WPR 25A fuse
Wiper / Washer System Operation
The windshield wiper motor module is part of the windshield wiper motor cover and controls the wiper motor operation. The windshield wiper motor is a 2 speed motor. Windshield wiper DELAY operation is a low speed wiper motor function with a variable delay interval between the wipe cycles. The DELAY interval is controlled through a series of resistors within the wiper / washer switch.
Park Position Operation
When the windshield wiper / washer switch is turned to the OFF position while the wiper motor is somewhere in mid-cycle, the wiper motor module will continue to operate the wiper motor until the wipers reach the park position. If the ignition is turned off while the wipers are in mid-cycle, the wipers will stop immediately where they are. The wipers will park the next time the ignition is cycled to the ON position.

Do you know how to do diagnostic's ?

Wipers Blades Do Not Park
Step
Action
Yes
No
Schematic Reference: Wiper/Washer Schematics
Connector End View Reference: Wiper/Washer Connector End Views
DEFINITION: This table diagnoses the wipers operate normally but will not return to the park position when the wiper operation is cancelled.
1
Did you perform the Diagnostic System Check - Vehicle?
YES - Go to Step 2
NO - Go to Diagnostic System Check - Vehicle in Vehicle DTC Information
2
Turn ON the ignition, with the engine OFF.
Move the wiper switch to the LO position.
Move the wiper switch to the OFF position.
Do the front wipers advance to the park position?
YES - Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO - Go to Step 3
3
Turn the ignition switch to the RUN position.
Turn the wiper switch to OFF.
Disconnect the wiper/washer switch connector.
Do the wipers park?
YES - Go to Step 7
NO - Go to Step 4
4
At the wiper/washer switch connector, measure the voltage of the windshield wiper switch signal 2 circuit.
Does the voltage measure greater than 1.0 volts?
YES - Go to Step 5
NO - Go to Step 8
5
Reconnect the wiper/washer switch connector.
Disconnect the wiper motor connector.
Measure the voltage of the windshield wiper switch signal 2 circuit.
Does the voltage measure greater than 1.0 volts?
YES - Go to Step 6
NO - Go to Step 8
6
Repair a short to battery positive voltage in the windshield wiper switch signal 2 circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
YES - Did you find and correct the condition?
NO - Go to Step 9
--
7
Replace the wiper/washer switch. Refer to Turn Signal Multifunction Switch Replacement in Steering Wheel and Column - Tilt.
YES - Did you complete the replacement?
NO - Go to Step 9
--
8
Replace the wiper motor cover. Refer to Wiper Motor Cover Replacement .
YES - Did you complete the replacement?
NO - Go to Step 9
--
9
Operate the system in order to verify the repair.
Did you correct the condition?
System OK
Go to Step 2

Jan 31, 2018 | 2005 Buick Century

2 Answers

'07 Impala Wipers Work Intermittently


Did you check for voltage at the wiper fuse? My info says that fuse is hot all the time. Use a digital multimeter. Everything off, take a reading across battery posts, the generic spec for a full charge is around 12.6 volts. You should get close to same reading at the wiper fuse, hopefully. When checking voltage at the fuse, use chassis ground not the other leg of fuse. There are wiper relays, those are pcb relays, they are soldered into the fuse box, you can't pull them out. Your bcm is also involved with those relays. Your multifunction switch basically tells the bcm you turned on your wipers, then the bcm controls voltage or ground for the relays. You can see wire color for hi and lo speed voltage. Maybe a problem with fuse box or wiring circuit if voltage is low? I hope this was of some help?
wiper-byjr2x1a1ejmcnbtj5cbblt2-1-0.jpg

Dec 04, 2017 | 2007 Chevrolet Chevrolet Impala LT

2 Answers

Windshield wipers won't shut off


Turn wipers to off then turn the car off. We have the same problem in our 1986 Pontiac parisienne brougham

Nov 23, 2012 | 1986 Pontiac Parisienne

1 Answer

After turn on windshield wipers, they will not


There is two place that you can check which would cause this problem. (1) the switch it self and the other is the (2) circuit board on the wiper motor. It's common for the solder on the circuit board where the wire harness clips on the wiper motor to crack and needs to be re soldered. You can buy the replacement at Auto Zone or you can re solder it your self to safe you the $15.00 for the board. If you give it a light tap and the wipers stop, then it's the circuit board. If it keeps working, then it's the switch on the steering column and you can get that at Auto Zone also and they will have the step by step instructions for you to get the hob done with common tools. Good luck and keep me posted.

Jan 07, 2010 | 1992 Pontiac Sunbird

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,540 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8826 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...