Question about 1999 Jeep Cherokee

3 Answers

OIL PRESSURE SENDING UNIT ON MY JEEP CHEROKEE 1993 WHERE IS IT LOCATED AND IS THERE A DIAGRAM OR PICTURE LOCATION FOR IT

Posted by on

  • mcriner Jan 11, 2009

    my lifters when the jeep is cold sound like they are not getting oil till the jeep warms up than they sound just fine.I have plenty of oil using synthetic oil.i think it is my oil sending unit going bad.

×

3 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I also thought I had a problem with the oil pressure switch (sending unit) because after an oil change from a new place I tried the check gage light came on and the oil gauge kept going up and down. The real problems was they put 5 w 30 w instead of 10w 30w. I went back and ask them to put the 10w 30 w and flush the other oil out and I drove my 1999 Jeep Grand Cherokee Laredo with 243,150 miles for 30 miles to cycle the oil and the problem went away. This company could have ruin my engine by putting light weight oil in my Jeep. God is good!

Posted on Dec 21, 2009

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

It should be right next to the oil filter which is passenger side of the engine block. I think on Grand Cherokees they are rubber coated. Careful though from the heat and everything they become brittle and break easily. I hope this helps.

Posted on Oct 09, 2008

OIL PRESSURE SENDING UNIT ON MY JEEP GRAND CHEROKEE LAREDO 1999
WHERE IS IT LOCATED AND IS THERE A DIAGRAM OR PICTURE LOCATION FOR IT

ANY SPECIAL KNOWLEDGE TO PUT IN?

Posted on Oct 01, 2008

1 Suggested Answer

  • 82 Answers

SOURCE: OIL PRESSURE SENDING UNIT ON

It is located on the passenger side of the block near the oil filter housing, shaped like a little bell. Part#is 56026779 and list for $40.35 at a Jeep dealer.

Posted on Jan 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is pressure sending unit located on 1995 jeep grand Cherokee limited 5.2liter V8 also oil sensor location


Your best bet is to buy a Haynes or chiltons manual for your vehicle. It will have the locations of the sensors as well as a wealth of other ideas and short cuts. I Purchased one for my Dakota thru ebay for about 10 dollars.

May 07, 2015 | 1995 Jeep Grand Cherokee

1 Answer

2005 jeep grand cherrokee location of oil pressure sending unit switch 4.7 l engine


its next to filter. the sender fits to the main oil gallery
like the filter too.
why not just look at the dealer parts page, find it and see.
the fsm covers this too.
page 4804 (posted many times now)


25586465-cuky5fb52wfczksibethvkr1-3-0.jpg

Mar 17, 2015 | 2005 Jeep Grand Cherokee

1 Answer

I AM TRYING TO REPLACE A SEAL ABOVE THE OIL FILTER AND NEED A SPECIAL KIND OF WRENCH, DO YOU KNOW WHAT KIND OF WRENCH IT IS. A BUDDY THINKS IT IS A HEX BOLT


You might be looking at the oil pressure sending unit in this location...in that case, an oil pressure sending unit socket is what you need...many mechanics still use channel locks to remove/replace this unit...Hope this helps.

Feb 01, 2011 | 1993 Jeep Grand Cherokee

2 Answers

Where is the oil pressure sending unit on a 1993 jeep grand


on the 4.0 motor Under hood, passenger side, lower engine area, rear of distributor, mounted in engine block.
on the v8 Under hood, center, rear engine area, passenger side of distributor, mounted in block.

Feb 09, 2010 | 1994 Jeep Grand Cherokee

1 Answer

Where is the oil pressure sending unit located on a 2000 jeep grand cherokee 4.0 liter


Removal & Installation
  1. Disconnect the negative cable from the battery.
  2. Raise vehicle on hoist.
  3. Remove front splash shield.
  4. Disconnect oil pressure sender connector (4).
  5. Remove the pressure sender (2).
6eaedba.gif
Oil pressure sending unit


To install:
  1. Install oil pressure sender.
  2. Connect oil pressure sender wire.
  3. Install front splash shield.
  4. Lower vehicle.
  5. Connect the negative battery cable.

Jan 12, 2010 | 2000 Jeep Grand Cherokee

1 Answer

1993 Jeep Grand Cherokee, V6. Oil Pressure Gauge Read High.


it could be the sensor you should look at the oil pressure relief valve

Jun 10, 2009 | 1994 Jeep Cherokee

1 Answer

Oil pressure reads maximum on gauge when driving, half at idle


Replace the oil pressure sending unit. But like emissionwiz said, location depends on the engine size.

Mar 23, 2009 | 2002 Jeep Grand Cherokee

1 Answer

No oil pressure


Sounds like sending unit, should be located by where the oil filter is.

Feb 26, 2009 | 1996 Jeep Grand Cherokee

1 Answer

OIL PRESSURE SENDING UNIT ON MY JEEP CHEROKEE 1993 WHERE IS IT LOCATED AND IS THERE A DIAGRAM OR PICTURE LOCATION FOR IT


It is located on the passenger side of the block near the oil filter housing, shaped like a little bell. Part#is 56026779 and list for $40.35 at a Jeep dealer.

Jan 08, 2009 | 1999 Jeep Cherokee

Not finding what you are looking for?
1999 Jeep Cherokee Logo

1,080 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...