Occaisional engine misfire, sometime causing engine to stop running

Engine misfire ! Flashing check engine light , catayltic converter damaging misfire . Been on for three years ? No inspection were you live ? Flashing check engine light CarMD

Diagnose Engine Misfire - Auto Diagnosis Repair Help

www.aa1car.com/library/misfire.htm

The engine may shake so badly at idle that it causes vibrations that can be felt in ...The engine may only misfire and run rough when cold but then smooth out as ...

What is causing an intermittent misfire only when engine is ...

community.cartalk.com/.../what-is-causing-an-intermittent-misfire-only-...

Jun 27, 2013 - NOTE: You MUST restart the engine for the misfire to go away. ... in an expert to do that test, but it might be worth it to prove/disprove the injectors being thecause. 0 ... The first is that the car should run fine even on cold starts.

Engine misfires when cold but runs fine after warming up few ...

https://answers.yahoo.com/question/index?qid...

Mar 24, 2009 - They also gave it to me because of this misfire problem it has. ...Engine misfires when cold but runs fine after warming up few minutes later? ... and you start next morning will also cause a misfire until it burns off the coolant.

"Miss/splutter" with cold engine, but fine when warm? M103 / also ...

www.peachparts.com > ... > Tech Help

Jul 13, 2011 - My moms old 300SEL (with the M103) that was once my car is now my "work car" again as she is getting a brand new SUV very soon.

Cold start misfire solved (finally!) - Bimmerforums

look for wires going to oil pan or just above it. That would be the oil level sensor.

This sounds like you might have a bad plug wire or something else in the ignition system is arcing to ground. A quick way to verify this is to run the truck in Park at idle. Next, spray the ignition wires with Windex. You'll notice the truck starting to rough up and might even see the bad wire arcing to ground. A complete tuneup would be recommended in this case.
I hope this helps! :)

check fuel pump pressure- fuel filter --air filter --egr valve if carboned up clean or replace and cat converter feel the exhaust if feels restricted may be clogging up

For engine misfiring problem check the help links mentioned below. Click the link below to go through the troubleshooting procedure :---- OBD-II Trouble Code P0300? http://schematicsdiagram.blogspot.com/2011/12/obd-ii-trouble-code-p0300.html
---------- Engine misses and truck jumps? Hard to down shift? Issue with high gear only? http://technoanswers.blogspot.in/2012/02/engine-miss-and-truck-jumps-hard-to.html

-----------
Bad miss at idle?

http://technoanswers.blogspot.com/2012/01/bad-miss-at-idle.html

-----------
While stop engine idles like cylinder missing?

http://schematicsdiagram.blogspot.com/2012/01/while-stop-engine-idles-like-cylinder.html

------------
Engine Misfire codes for car?

http://schematicsdiagram.blogspot.com/2011/12/engine-misfire-codes-on-chevrolet.html
Engine Misfire codes?

http://schematicsdiagram.blogspot.com/2011/12/engine-misfire-codes-on-chevrolet.html

--------------
Misfire on cylinder 4?

http://schematicsdiagram.blogspot.com/2011/12/misfire-on-cylinder-4.html

-----------
Oil on spark plugs and car misfires?

http://technoanswers.blogspot.in/2012/02/oil-on-spark-plugs-and-car-misfires.html

----------

This will help.

Thanks.

Running out of gas causes the scum in the bottom of your gas tank to be fed to you engine. I replace the fuel filter every 30000 miles.You might have allowed scum into one of you injectors. Try replaceing that spark plug first.Dont run out of gas.

P1391 TROUBLE CODE IS INTERMITTENT LOSS OF CAM OR CRANK SIGNAL..WHAT SIZE ENGINE IN YOUR CAR?2.7/3.2/3.5?SOME MORE INFO WOULD HELP..ALSO YOUR HEATER FAN PROBLEM SOUNDS LIKE A FAULTY HEATER RESISTOR..PICK UP A NEW ONE..FAIRLY INEXPENSIVE..LOCATED IN HEATER HOUSING ON RIGHT SIDE UP UNDER DASH..IF YOUR NOT SURE HOW TO REPLACE..CONSULT A PROFESSIONAL..

P0300 is a random engine misfire code. P 1781 is a transmission code, but it refers to a malfunctioning engine speed signal (crankshaft angle sensor). A bad crankshaft angle sensor or camshaft angle sensor can cause the P0300 code. A large list of items can cause a P0300 code, but since you have both, I'd be checking the crankshaft angle sensor and the related circuit. Sometimes, the mounting screws loosen up, which can cause the sensor to not function properly, all the time. Get this fixed, because over a period of 4 to 6 months, this can destroy the catalytic converter in the exhaust system ($$$$)
Charlie

Here is a list of possible causes. You should not drive the vehicle if the check engine light is flashing all the time, you can cause even more damage. It could pay to have a professional find the real cause.

Spark plugs that are incorrect for the application, cracked, improperly gaped or worn can cause the engine to misfire or run rough at all times.
An IC module that failed to correctly control the ignition coil(s) will cause the engine to misfire or run rough at all times.
Poor connections, broken wiring or wiring that has shorts to ground can cause the engine to misfire or run rough at all times. NOTE: Check connectors that might be pulled apart as the engine flexes or wires that short to ground as they pass near brackets or shorts to ground on the exhaust manifold.
Fuel injector(s) that are shorted, plugged or partially restricted can cause the engine to misfire or run rough at all times.
An ignition coil(s) that has low output, corrosion on the coil tower(s), is carbon tracked or arcs to ground will cause the engine to misfire or run rough at all times.
A PCM that failed to properly control the injector or ignition timing will cause the engine to misfire or run rough at all times.