Horn do i need to take the steering wheel off?

images for 2004 Suzuki Forenza no controls on



Suzuki Steering Wheels and Horns ' eBay

www.ebay.com/sch/Suzuki-Steering-Wheels-and-Horns/.../i.html
eBayFind great deals on eBay for Suzuki Steering Wheels and Horns in Steering ... 2004Suzuki Aerio Grey and Black Steering Wheel with Airbag OEM 2003 ... 04 05 06 07 08SUZUKI FORENZA- Steering Column, Black with Key, NO AIRBAG ... 2006 Suzuki Aerio Gray Leather Steering Wheel with Controls OEM 05 06 07 Nice.

You might need to disassemble the steering wheel to access the horn button / switch there' could be something loose in there which is causing a closed circuit when the steering wheel is turned. May be solved by tightening or the horn button / switch may need replacing.

Need to disassemble the steering wheel to access the horn button / switch -- there's something loose in there which is cauing a closed circuit when the steering wheel is turned. May be solved by tightening or the horn button / switch may need replacing.

Charlie

First go to horn, its in the right side (passenger side) very front behind bumper. Turn wheel to the right, remove inner fender well, locate horn. Check to see if you have 12V there when the horn is activated to ensure its not just a horn. If there is 12V and ground and horn doesn't sound, you'll need a new horn. If voltage is good then back track to the horn relay, it should be under the hood electrical center (some earlier models were under the dash below steering wheel. If you press on the horn in the steering wheel, you should hear it click to locate. If not check the black wire going up the steering column, when jumpered to ground and horn sounds then the problem is inside the steering wheel, horn ring or contacts on the pad are faulty.

It sounds like your clock spring, as we call it, has failed under the steering wheel. To remove the assembly you must first disconnect the negative battery cable to avoid deploying the air bag. There are 2 to 4 screws on the back of the steering wheel holding the horn pad onto the wheel. Remove those screws and carefully lift the horn pad off and disconnect the wire plugs. The horn wire is usually red and the air bag usually yellow. You will need a cheap steering wheel puller from the local auto zone to remove the steering wheel. They have a small round disc type that is easy to use and cheap. Now remove the large nut from the center of the steering shaft. Install the tool and remove the wheel. Now you will see a large round disc or air bag ribbon held on by a clip. use an pick tool and a small screw driver to remove this clip. Now trace the wires under the column and unplug the other end and you can remove the ribbon or clock spring. Now feed in the wiring for the new ribbon and reverse the process to reassemble. While you have the horn pad off test the horn switch to see if the horn pad is bad and may need replaced also. If the switch is good find the horn relay in the fuse box under the hood and see if when you press the horn does it get power from the switch. to test the horn itself apply 12volts to the two connectors on the horn and if it sounds it is OK. The system is made up of horn, horn relay, and horn switch. Thanks for looking for a solution at Fixya.com.

Find the horn and use a test light to try to ground out one of the two terminals to see if it sounds. If it does, then the horn is ok, but it may be the switch in the steering wheel.

To test the steering wheel switch, take the horn cover off of the steering wheel and search for the lead for the button and try to ground it out. It may sound if you do this. If it does, then there is something wrong with the button connection at the clock spring.
---
Here are instructions on how to remove and replace the steering wheel which can help to understand how to troubleshoot the horn switch which is related to the clock spring electrical connector:

Steering Wheel Removal & Installation To Remove:
NOTE: Make sure the wheels are in the straight-ahead position. Disconnect the battery ground cable and wait at least one minute.
WARNING
To avoid the risk of serious personal injury, read and follow all warnings, notes and instructions in the deactivation procedure. Deactivate the supplemental restraint system (SRS).

1. Remove the driver side air bag.
2. Disconnect the clockspring electrical connector.
3. Remove and discard the steering wheel bolt.
4. Use steering wheel puller and remove steering wheel.

CAUTION
Removing the steering wheel without using a puller can damage the column bearings. Using a suitable puller, remove the steering wheel.
Remove the steering wheel while routing the wires from the clockspring through the steering wheel.
WARNING
To avoid the risk of serious personal injury, read and follow all warnings, notes and instructions in the reactivation procedure. Reactivate the supplemental restraint system (SRS).
To Install:

1. Install steering wheel, while guiding wires from clockspring through.
2. Install new steering wheel bolt. Tighten to 30 ft. lbs. (40 Nm).
3. Connect the clockspring electrical connector.
4. Install the driver's side air bag.

have to pull strng wheel off you have a horn wire grounding out when you turn wheel only 2 wires biggest issue pulling steering wheel

remove and clean contacts.

The HORN Is a GROUND CONTROLLED BUTTON you need to FIRST Check under CENTER STEERING WHEEL Cover to see if it has a Bad Commectiot, After Asuring this there Is c CLOCK Spring UNDER Steering Wheel that is Fairly Common for Failing.

The FOB / Remote Utilizes a Different Part of the Curcuit to Activate Horn, I Hope this Helps you With your Problem as Im Sure of All that I Advised. Remember to RATE ME !!

Are you speaking of the horn? Or the horn relay? Or the horn button? Or the horn button split ring armature? To remove the horn assembly in the steering wheel you will need a steering wheel puller and a U shaped clamp that will screw down to the steering bolt you will need a 3/4 socket with a 3-inch extension and a ratchet. You will also need to picks to pull center snap ring off to get to the parts under the plate for the horn. To remove you will need to buy 2 security nuts tork wrenches #8 I believe, you will have to disconnect the battery before working on it as the bag could explode if you do not have the battery disconnected. After removing the positive side of battery cable wait 5 minutes before proceeding. Then remove the two bolts that hold the front horn assembly and air bag from the rear of the steering wheel next remove horn air bag assembly and disconnect the wire for the air bag. Place horn to the side then remove the 3/4 bolt out from the center, next install steering wheel puller on the steering wheel and put in three bolts and tighten them evenly so that the puller is on straight. Screw center bolt into the steering bolt until the wheel comes loose, remove steering wheel and place it at the side, next use the U shaped clamp to press the center plate down 1/4 inch to be able to clear the snap ring around the steering wheel. With one pick hold the ring in place with the other force it between the steering wheel bolt and work the ring up and out of the grove it sits in. Next work it all the way up till you have it in your hand, and do not lose. Now pull plastic plate off if you put the wheels straight then it will go on the same way you pulled it off because it's keyed mark it with a felt tip pen so you don’t have to hassle with keying it in again. Next remove the plate and there you will find the horn contacts and the round disk that the connectors push against, so if you need more info just ask on this post.