Question about 2003 Mitsubishi Lancer

1 Answer

Tail Light The problem that I am having is that the tail light on the passenger side of the car is not working. The tail light is working so I changed the fuse and the bulb and still no luck. What can I try now?

Posted by on

  • Anonymous Sep 21, 2008

    My back-up lights are not working. I have replaced both bulbs and fuse. What else can I do?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

Sounds like your bulb socket is bad. you can buy them in any auto shops. mine did that and i replaced it and it was fine. I would look at the one that is not working and compare the size and try it.

Posted on Jun 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2005 Chevy Equinox passenger side tailight doesn't work. Brake light, turn signal, and hazard work but unit does not illuminate at night. Easy fix ?


Have you tried swapping the bulb from the other side see if that works If not check for power and ground at the tail lamp circuit that is inoperative. Also take a good look at the connector(s) make sure there is no corrosion in the terminals.

May 19, 2014 | Cars & Trucks

1 Answer

I would like a diagram of the 740 gle 1990 tail light wiring, I cannot seem to get them working correctly


You don't really need a diagram, it's simple. If you open both tail light boxes in the trunk you will see at the connector on the bottom a yellow wire in the first position. That goes to the brake bulb. If both tail lights do not work, make sure you are getting power to the driver side light first, if it is not getting power, the passenger side will not work either, they are in line with each other. If it is only the passenger side not working, the bridging wire could be bad.. try jumping it. Also, make sure you are getting power inside the tail light bulb holder. The metal connections can come loose. If there is no power to the driver side tail light it could be the bulb failure relay, that is the round red relay in the rear left side of the fuse box behind the ash tray/ cigarette lighter below the radio in front of the shifter. You should be getting power to the third brake light in the rear window...that is a different circuit and will not be affected. Try changing out the bulb failure relay, it supplies the power to the tail lights.

Jun 22, 2011 | 1990 Volvo 740

1 Answer

Passenger tail light inoperational. i switched the harnesses and the driver side works when i switch the female ends. found a frayed wire on the passenger side... spliced it and did not get any changes. ...


check the driver side! Usually those old subs were wired to use the driving side first and then pigtail over to the passenger side... Also, alot of the tail light problems are caused from mud & snow piling up behind your back bumper... this cause weight on the wires and SNAP! Tail lights stop working! You're just going to have to follow that wire harness back until you find it! By the way, Check your ground behind the tail light covers! They also tend to rust and loose connections! Another problems are the sockets going bad! I replaced mine about once evey 5 years... annoying, bad got to love suburbans!

Apr 26, 2010 | 1986 Chevrolet Suburban

1 Answer

2006 Ford Ranger. Rear passenger side tail light


Bad earth connection.Clean or replce wire.

Jun 18, 2009 | 2004 Ford Ranger

1 Answer

Tail light out replaced both brake & tail lite bulbs nothing


It sounds like your brake light switch is out.  It's located on the brake pedal and is relatively easy and cheap to replace.  Let me know if you have any questions.  Thanks for rating my response and for using FixYa!

May 27, 2009 | 1997 Chrysler Town & Country

1 Answer

Head light and tail light wont work


the headlight switch may have a short in it. replace switch and try again.

Feb 27, 2009 | 2003 Ford Windstar

1 Answer

Mazda 3 tail light on, brake light not on


The bulb actually has two seperate elements in it.
That is why the tail light works fine.

If you take the bulb out you will see the seperate elements.
Change the bulb and it should be fine.

Jan 09, 2009 | 2004 Mazda 3

Not finding what you are looking for?
2003 Mitsubishi Lancer Logo

188 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...