Question about 2000 Oldsmobile Alero

1 Answer

Oil light where is the change oil light reset button on a 2000 alero 3.4L 2 door

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Driver side. fuse box . take off . there should be a red reset button that looks like a fuse

Posted on Aug 16, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I got an alero 2000 how do reset for checkengine and change oil lights??


On the drivers side there is a fuse panel, you will need to remove the cover and there you will see a reset button. Turn the ignition switch to on and then press the button, the light will flash, then press and hold the reset button until the light goes off, this will also work for the TPS system. Hope that helps

Jan 13, 2011 | 2000 Oldsmobile Alero

Tip

Oldsmobile service light 1991-01


Alero

2000-01

Turn the ignition to the ON position, engine OFF. Press the RESET button and release. The CHANGE OIL indicator will start flashing
2000: Press and release the RESET button again.
1999: Press and hold the RESET button until an audible chime is heard and then release the button.


Intrigue


2000-01

Turn the ignition to ON without starting the engine. Fully press and release the accelerator pedal three times within five seconds. If the CHANGE OIL SOON indicator flashes two times, the system is resetting. Turn the key off after the the light has finished flashing, then start the vehicle. If the CHANGE OIL SOON indictor comes back on, the engine oil life monitor has not reset. Repeat the procedure again. If the vehicle is equipped with the U20 option code, the vehicle as an oil life low indicator. The oil life low indicator shows an estimate of the oil's remaining useful life. When the oil life index is less than 10 percent, the display will show OIL LIFE LOW. To reset the oil life monitor, press and hold the MODE button until the light appears next to OIL LIFE. Press and hold the trip RESET button until the oil life percentage changes to 99 percent.


Alero,
Intrigue,
Cutlass Supreme


1999,
1998,
1996-9

To reset the "CHANGE OIL" light, turn the ignition switch to the "RUN" position with the engine off. Fully depress and release the accelerator pedal three times in five seconds. The light will flash twice and go out.


Aurora


1995-99

To reset the "OIL LIFE" message, press the "ENG" button with the ignition on until "OIL LIFE PERCENTAGE" is shown. Press the "RESET" button for 5 seconds. "RESET" will appear and then "OIL LIFE" will show 100%


Eighty-Eight,
Ninety-Eight,
Regency


1994-97

When "CHANGE OIL NOW" is displayed, press the "RESET" button. Press "SEL" to display "OIL". Press "SEL" to display oil life. Press and hold "RESET" for 5 seconds. A "RESET" message should display with oil life changed to 100%.


Eighty-Eight,
Ninety-Eight


1992-93,
1991-93

Press and release the "TEST" button on the Driver Information Center. This will illuminate "CHANGE OIL NOW" if it is not already illuminated. Press and release the "OIL" or "OIL INDEX" button. Next, press the "RESET" button and hold for at least 7 seconds.


Toronado,
Trofeo

w/o CRT Display

1991

To reset "OIL LIFE INDEX", press the "2 OPTIONS" button: three times if the vehicle is equipped with a phone and compass, once if equipped with neither. While "OIL LIFE INDEX" is displayed, press and hold the "RESET/ENTER" key at the bottom right of the 15 button switch for 5 seconds.













on Dec 07, 2009 | Oldsmobile Alero Cars & Trucks

1 Answer

2000 olds alero oil change and check air pressure light is on , i changed the oil and cheched air pressure . tried to reset but light stayes on


Open the driver door on the car and locate the fuse panel on the SIDE of the dash. Remove panel and there will be a red reset button. Turn key to the ON position and press and release button. Press and hold button again, and you will hear a series of beeps signaling that it has been reset

Nov 09, 2010 | 2001 Oldsmobile Alero

3 Answers

I had the oil changed but the change oil light is still on, how do i reset the computer? 2000 oldsmobile alero


How to Reset the Change Oil Light

After changing the engine oil, the system must be reset.

With the ignition key to ON, push the RESET button

located in the driver's side instrument panel fuse block. The

CHANGE OIL light will start to flash, press and hold the

RESET button again. The reset is complete when you hear
the chimes sound and the CHANGE OIL light goes out.

Oct 25, 2010 | 2000 Oldsmobile Alero

1 Answer

How to reset dash lights on oldsmbile alero after changing oil


turn the key to the "on" position and press the reset button in the fuse panel just inside the drivers door once the change oil light starts blinking press and hold the reset button until you hear a chirp sound and the light goes out.

May 01, 2010 | 2000 Oldsmobile Alero

2 Answers

I HAD MY OIL CHANGED ON MY 2000 OLDSMOBILE ALERO,


in the control panel one the right side of the car there is a reset button. all you have to do is turn the car to when all the lights are flashing and hold the reset button until the car dings.

Apr 15, 2010 | 2000 Oldsmobile Alero

2 Answers

How do I reset the oil change light???


On the left side of the driver door you will see a fuse panel. Open it, turn the ignition to on position, press the reset button once, the light will start flashing, Press and hold the reset button till the light goes out. Note also works for the tire pressure light.

Mar 15, 2010 | 2000 Oldsmobile Alero

1 Answer

Just got an oil change but the "oil change" light is still on, how do I reset it?


drivers side fuse block, remove cover
1.turn key on (engine off)
2. push the reset button in
3. change oil light will start to flash, press and hold reset button again, reset is complete when you hear the chimes sound and the change oil light goes out

Feb 05, 2010 | 2000 Oldsmobile Alero

1 Answer

I have a 2000 olds alero, how do i reset the change moil light


If you mean the change oil soon light............ Open the fuse panel; on the side of the dash by drivers door. turn on key but not far enough to start car.
Press the red reset button in the fuse panel until the oil light flashes , release the button and then press it again.
It has been a while since I have done this on an alero , so if you have your owners manual , it might be a good idea to read the instructions in there incase i have it wrong. By the way , the low tire pressure light works the same way.

Nov 08, 2009 | 2000 Audi A6

2 Answers

Change oil light


After you change your oil you must reset your system to start tracking your next oil change. Simply take off your fuse panel cover. There is a red button in there marked RESET. To do this simply turn your ignition switch on (not started). Then press the RESET button once. You will now see your Change Oil Light blinking. Hold down on the button until you hear it beep. Turn off your ignition switch. Now start your Alero, the light should be off.

Jan 06, 2009 | 2001 Oldsmobile Alero

Not finding what you are looking for?
2000 Oldsmobile Alero Logo

Related Topics:

236 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...