Question about 1983 Chevrolet Impala

Open Question

Assembly instructions for steering column

Need graphic assembly instructions for 1958 chevy impala steering column

Posted by on

6 Suggested Answers

DAD5bbbbg
  • 111 Answers

SOURCE: replace a steering column on 1989 chevy k5 blazer

The best thing to do is to buy a Chilton,s repair manual. It has step by step procedures. You can get one at most auto parts stores. They coast anywhere from $10-$30 dollars.

Posted on Mar 16, 2009

  • 6 Answers

SOURCE: Wobbly steering column on 1989 Chevy Silverado 2WD

It is rather complex but it can be done at home. It will also require special tools. The haynes manuals do cover this repair I believe.

Posted on Apr 19, 2009

csmock132
  • 4669 Answers

SOURCE: nned steerin column diagram

I don't have a diagram, But I have taken tons of these apart. Is there something I can help with?

Posted on May 04, 2009

  • 3600 Answers

SOURCE: My 1990 chevy astro mini-van has a loose tilt

Ok Here is what you need to do this job
1. #8 tork head wrench
2. # 3 tork head wrench
3. New cylinder or lock buy at junk yard or from dealer or lock smith with keys.
4. Tube of lock tight
5. steering wheel removal tool Rent it from Schucks
6. steering wheel spring compression tool Rent it as well.
7. Two dental picks to remove spring.
Now make thew wheels straight and pull the horn button off should just pop off, next you will see a nut 3/4 inch remove the nut now find the right size of threaded bolts out of the kit and put them in the holes with puller over the steering column remove steering wheel. Forgot to mention remove the metal cup and plastic ring held on by a3 philips screws. This is your horn button, next put the U shaped compression tool on the bolt that you took the nut off and compress the spring 1/4 of an inch to 3/8's of an inch. Now take the picks and get them under steel ring slide the ring over the steering bolt and pull clamp off now remove plastic plate you are now where you can get to the 2 screws on top to tighten the steering wheel. you will see a screw just at the end of the cylinder lock remove the one screw and pull the cylinder lock out, put a drop of lock tight on each screw and tighten down look to see if you see a wire by the lock ring is sticking up it will have a 45 bend in the copper wire there will be two one side by side this has to be pulled out along with the plastic holder that holds the two wires in this also holds the lock in as well as the one screw, install the new lock put lock tight on the screw and install new cylinder lock and key once you have done all of this leave it apart and get back to me so I can tell you how to remove the bueaty ring to get to the screw on the back side.

Posted on Jun 15, 2009

  • 10 Answers

SOURCE: power steering fluid in '04 chevy impala

i have an impala Ls 3.8 liter and (not sure about the 3.4 liter) but mine is located in the back of the engine near the middle. and get a long thin funnel because its down a little ways.

Posted on Mar 07, 2010

  • 701 Answers

SOURCE: i need a steering column

Hello julesck41: My name is Roger and I will help. The picture and part list my not all come through or come through real clear.But i will try. Should you need more help lease just ask. I will do all I can Thank You for using and trusting Fix Ya. Rogerrogerf1_7.jpgrogerf1_8.jpg

Posted on Dec 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace headlight dimmer switch on a 2003 chev impala do I have to pull the steering wheel


Yes , the steering needs to be pull .
Disable the SIR system. Refer to SIR Disabling and Enabling in SIR. Remove the steering wheel. Refer to Steering Wheel Replacement . Remove the upper and lower trim covers. Refer to Steering Column Trim Covers Replacement .
Important: The abrasion sleeve located on the steering column wire harness assembly must be reinstalled. Make note of what connector is coming out of the abrasion sleeve for installation purposes.
Remove the wire harness assembly (1) from the wire harness strap (2). Disconnect the turn signal and multifunction switch assembly connector from the SIR system coil connector.
There could be a video on youtube show how to do it .
Theret

Oct 20, 2016 | Cars & Trucks

1 Answer

Need diagram steering column 1984 chevy


Two screws located on steering wheel back to remove horn assembly to expose steering wheel locknut to remove and then use steering wheel puller to remove the st wheel and expose switch.

Jan 07, 2014 | Nissan Cars & Trucks

1 Answer

2007 chevy impala LT, horn and cruise control not working. Cruise control is not working, the light does not come on at all. The horn works with the remote starter but not when pushing on the steering...


most likely the clockspring or ribbon assembly inside the steering wheel has a broken spot in it. if you try to do it yourself be careful with the airbag system

Jul 14, 2011 | 2007 Chevrolet Impala LS Sedan New Cars

1 Answer

How do i install Switch Assembly turn signal Cruise control PART AUTO for a 2002 Impala.


Multifunction Turn Signal Lever Replacement - On Vehicle

Removal Procedure

83422682


  1. Verify that the multifunction turn signal lever is in the center of the OFF position.
  2. Disconnect the negative battery cable.
  3. Disable the SIR system.
  4. Remove the steering wheel.
  5. Remove the steering column trim cover.
  6. Remove the steering column knee bolster.
  7. Remove the steering column wire harness (1) from the steering column wire harness retainer (2).
  8. Remove the 2 wire harness straps from the steering column wire harness (1).
  9. Remove the steering column bulkhead connector from the vehicle wire harness.
  10. Disconnect the connectors from the multifunction turn signal lever steering column bulkhead connector.
85097560




  1. Remove the retaining bolts (1) from the multifunction turn signal lever (2).
  2. Remove the multifunction turn signal lever (2) from the steering column.
Installation Procedure

85097560




  1. Install the multifunction turn signal lever (2). Use a small flat-blade in order to compress the electrical contact and move the multifunction turn signal lever into position.
  2. Verify that the electrical contact rests on the canceling cam.
Notice: Refer to Fastener Notice in Service Precaution.


  1. Install the retaining bolts to the multifunction turn signal lever.
    • Tighten the retaining bolts to 7 Nm (62 inch lbs.) .
92905224




  1. Connect the gray and black connectors to the multifunction turn signal lever steering column bulkhead connector.
  2. Connect the steering column bulkhead connector to the vehicle wire harness.
  3. Install the two wire harness straps to the steering column wire harness (1).
  4. Install the steering column wire harness (1) to the steering column wire harness retainer (2).
  5. Install the steering column knee bolster.
  6. Install the steering column trim cover.
  7. Verify that the lever is in the center or the OFF position.
  8. Install the steering wheel to the steering column.
  9. Enable the SIR system.
  10. Connect the negative battery cable.
I hope this helps you.

Thanks

Nov 28, 2010 | 2002 Chevrolet Impala

1 Answer

How do i remove the turn signal switch on a 2001 chevy impala


Removal & Installataion
  1. Verify that the multifunction turn signal lever is in the center of the OFF position.
  2. Disconnect the negative battery cable.
  3. Disable the SIR (air bag) system. Refer to the Chassis Electrical Section.
  4. Remove the air bag module from the steering wheel.
  5. Remove the steering wheel.
  • Remove the upper and lower steering wheel trim covers using the following procedure.
    • Remove the tilt lever assembly.
    • Remove the two pan head tapping screws from the lower shroud.
    • Unlock the upper and lower shroud.
    • Remove the two Torx® head screws from the upper shroud.
    • Remove the upper shroud.
  • Remove the wire harness straps from the wire harness assembly and detach the wiring harness connectors from the switch side connectors.
  • Remove the two multifunction turn signal switch screws and remove the multifunction switch assembly from the vehicle.
  • To install:
    1. Install the multifunction switch to the steering column. Use a small flat-blade prytool to compress the electrical contact and move the multifunction turn signal switch into position. Verify that the electrical contact rests on the canceling cam. Install the screws and tighten to 62 inch lbs. (7 Nm).
    2. Route the wire harness along the steering column jacket assembly and secure into the wire harness strap. Install a new wire tie to the upper tilt head assembly and another lower along the wiring harness, as the original installation.
    3. Verify that the lever is in the center of the OFF position.
    4. Install the upper and lower steering column shrouds.
    5. Route the SIR connector through the steering wheel, align the scribe mark on the steering wheel made at removal, with the slash mark on the steering shaft and install the steering wheel. Install the steering shaft nut and torque to 30 ft. lbs. (41 Nm).
    6. Install the horn contact leads and the air bag connector to the back of the air bag. Make sure the CPA wedge is in place to secure the connector. Install the air bag by gently pushing on both the right and left sides of the air bag until the retaining springs engage.
    7. Enable the SIR system by connecting the yellow 2-way connector at the base of the steering column and installing the air bag fuse.
    8. Connect the negative battery cable. Test the horn, turn signals and headlight operation.

    Mar 06, 2010 | 2001 Chevrolet Impala

    1 Answer

    Install a Ignition lock cylinder 1997 Pontiac Grand Am


    • Ignition Removal Instructions
    • Disconnect the negative battery cable from the battery. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
    v\:* {behavior:url(#default#VML);} o\:* {behavior:url(#default#VML);} w\:* {behavior:url(#default#VML);} .shape {behavior:url(#default#VML);} Normal 0 MicrosoftInternetExplorer4 st1\:*{behavior:url(#ieooui) } /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman";}
    • Remove the upper and lower shrouds. Refer to Steering Column Trim Covers - Disassemble - Off Vehicle or Steering Column Trim Covers - Disassemble - Off Vehicle .
    • Put the key in the steering column lock cylinder set (1).

    • Turn the key to the "START" position.
    • Install a 1/16 allen wrench (2) into the hole on top of the lock module assembly in order to release the steering column lock cylinderset retaining pin.
    • Turn the steering column lock cylinder set (1) into the "RUN" position.
    • Pull the steering column lock cylinder set (1) out from the lock module assembly.
    • Remove the key from the steering column lock cylinder set (1).

    19eb1ff.png


    • Installation Instructions
    Normal 0 MicrosoftInternetExplorer4 st1\:*{behavior:url(#ieooui) } /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman";}
    • Insert the key into the steering column lock cylinder set (1).
    • LIne up the locking tab (2) and the positioning tab (3) of the steering column lock cylinder set with the locking tab slot (5) and the positioning tab slot (4) in the lock module assembly (6).
    • Push the steering column lock cylinder set (1) into the lock module assembly (6).
    • Rotate the steering column lock cylinder set (1) in the lock module assembly (6) into all positions.
    • Install the upper and lower shrouds. Refer to Steering Column Trim Covers - Assemble - Off Vehicle or Steering Column Trim Covers - Assemble - Off Vehicle
    • Remove the ignition key from the lock cylinder set (1).
    • Connect the negative battery cable to the battery. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical

    d612a25.png

    I hope this helps and good luck.
    Please remember to vote 962e1fb.jpg and leave a testimonial. Thanks.

    Nov 02, 2009 | 1997 Pontiac Grand Am

    1 Answer

    Disarming therftlock radio on 2003 Chevy Impala.


    I think you may have read it incorrectly...you do not disarm it, you need to know the code, so when you are finished, you can turn it back on.
    If you don't have the code the dealer can give it to you.

    Jun 27, 2009 | 2003 Chevrolet Impala

    1 Answer

    Steering Column replacement


    Take off the cover underneath the dash. Push the rubber boot down at the very bottom (Sometimes you have to cut them a little to move them down far enough) Should be an 11mm bolt down there someplace. then disconnect everything and take off the other bolts should be 13s or 15s going straight up. then just yank it out to separate it from the rack and it should come right out.

    Jun 02, 2009 | 1996 Chevrolet Impala SS

    1 Answer

    Steering is loose


    Had the same problem with my 2005 Chevy Impala, the dealer put a kit on the steering column. It is a bushing of some type which took up the slack.

    Aug 02, 2008 | 2005 Chevrolet Impala

    1 Answer

    RHD to LHD conversion


    A company called Flying Spares in Warwickshire will be able to supply all the parts. I'm not sure if the steering box is part of the subframe assembly on these models, if it is, you'll need a new subframe setup & new stering box, but the rack is reversible I think and the steering column isn't a problem. 01455 292 959. Ask for Ben, tell him Dave Flora gave you the details. Good luck

    Jun 28, 2008 | Rolls Royce Silver Dawn Cars & Trucks

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    55 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    yadayada
    yadayada

    Level 3 Expert

    60769 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6811 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...