Question about 1996 Ford Bronco

2 Answers

How do i replace front wheel bearing hub assembly

Posted by on

  • FGA57 Aug 08, 2008

    FORGOT WHERE THE 2 THRUST WASHERS AND THE ONE OCTAGON THRUSH WASHER GO IN THE HUB ASSY.

  • Anonymous Feb 13, 2009

    how to take hub off on 1993 ford bronco shift on the fly

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 29 Answers

If you have 3 bolt auto hubs the washers go on right after the cam assembly the part with the nylon on the back it also has a spring around it

Posted on Jul 17, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Metal,plastic,splined,washer

Posted on Nov 23, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2wd.how to replace front wheel bearing assembly


There are a number of videos...
For RWD front hubs. (F250 will just have larger bolts.)

How To Install Replace Front Wheel Bearing Hub Assembly 2004-08 Ford F150
For 4x4 front hubs.

Ford Super Duty hub bearing replacement Driver side

May 06, 2016 | 2005 Ford F 250 Super Duty

1 Answer

Front wheel assembly diagram


For front wheel assembly diagram and replacement,click the link below and go through procedure:----Front wheel hub assembly Diagram and replacing procedure? http://howtobyme.blogspot.in/2012/02/front-wheel-hub-assembly-diagram-and.html
----------Front wheel assembly diagram to replace wheel bearing? http://howtobyme.blogspot.in/2012/02/front-wheel-assembly-diagram-to-replace.html
-------------How to replace Front wheel bearing? http://howtobyme.blogspot.in/2012/02/how-to-replace-front-wheel-bearing.html
-----------Check all 3 links one by one.This will help.Thanks.

Feb 22, 2012 | Ford F-250 Cars & Trucks

1 Answer

How do i change the front wheel bearrings on a 1999 sonoma 2 wheel drive?


The bearing is in the hub.. Here are some instructions for that:
  • The wheel bearing is installed in the wheel hub assembly and is serviced by replacement only.

  • You may need Torx sockets to remove the bearing assembly bolts.


  • Raise and support the front of the vehicle safely using jackstands.

    Remove the tire and wheel assembly.

  • At the wheel hub, remove the cotter pin and retainer, then loosen and remove the castle nut and the thrust washer. In order to hold the hub from turning when loosening the nut, insert a drift through the caliper and into the rotor vanes. Remove the brake caliper and support it aside using wire or a coat hanger. Make sure the brake line is not stretched or damaged.

  • Remove the brake rotor from the wheel hub.

  • Remove the bolts retaining the hub/bearing assembly to the knuckle, then carefully pull the assembly from the splined end of the halfshaft. If available, use J-28733-A or B, or an equivalent spindle remover to prevent damage to the shaft or hub/bearing assembly.


  • Remove the cotter pin from the drive axle end nut and retainer


    Remove the retainer for access to the end nut


    Loosen the drive axle nut-here the caliper is installed so a drift could be inserted to keep the disc from spinning



  • Read more: I want to replace my S10 front wheel bearing. My manual ... - JustAnswer http://www.justanswer.com/chevy/0jwks-want-replace-s10-front-wheel-bearing-manual.html#ixzz1hl5SCxBf

    Dec 26, 2011 | 1999 GMC Sonoma

    1 Answer

    How do i pull the hub off my 2002 mazda , on drivers side front


    REMOVAL & INSTALLATION Except Miata FRONT
    1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
    2. Remove or disconnect the following:
      • Steering knuckle from the vehicle
      • Inner oil seal from the knuckle
    3. Using Mazda Hub Puller tools 49 G033 102, 49 G033 104 and 49 G033 105, pull the front wheel hub from the knuckle assembly.
    4. Remove or disconnect the following:
      • Bearing inner race from the front wheel hub
      • Retaining ring from within the knuckle
      • Front wheel bearing from the knuckle, using the hub puller tools
      • Brake dust shield
    5. Clean and inspect all parts but do not wash or clean the wheel bearing. The bearing must be replaced. To install:
    6. Using Mazda Press tools 49 G033 107 and 49 H026 103, install a new dust shield cover assembly to the knuckle.
    7. Using the press tools, press a new wheel bearing into the knuckle assembly.
    8. Install or connect the following:
      • Wheel bearing retaining ring
      • New oil seal using Installation tool 49 V001 795
      • Front wheel hub using the Mazda press tools
    REAR
    1. Before servicing the vehicle, refer to the precautions in the beginning of this section. NOTE: The wheel bearings are not serviceable. If the bearings are bad, a new hub/bearing assembly must be installed.
    2. Remove or disconnect the following:
      • Rear wheels Fig. 1: Exploded view of the rear wheel hub and bearing assembly (disc brake model shown, drum is similar) 7923mg87.gif

      • Brake drum, if equipped
      • Rear caliper and rotor assembly from the hub, if equipped
      • Hub dust cover
    3. Raise the staked portion of the hub retaining nut with a hammer and chisel.
    4. Remove or disconnect the following:
      • Hub retaining nut and discard it
      • Hub and bearing assembly from the spindle Fig. 2: When installing the new hub nut, be sure to stake it into the notch on the spindle 7923mg86.gif
      To install:
    5. Install or connect the following:
      • Bearing assembly on the spindle. Torque the new nut to 131-173 ft. lbs. (177-235 Nm)
      • Stake the nut into the groove in the spindle
      • Dust cover
      • Assemble the brakes
      • Rear wheel

    Jan 01, 2011 | 2002 Mazda Protege

    1 Answer

    Left front wheel bearing replacement diagram


    Removal & Installation Front To Remove:
    The front wheel bearings are not serviced separately. If the front wheel bearings are defective, the hub and bearing assembly must be replaced.
    1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
    2. Lubricate the threads on the halfshaft with clean engine oil.
    3. Remove or disconnect the following:
      • Front wheels
      • Halfshaft hub nut
      • Caliper from the steering knuckle WARNING
        DO NOT allow the brake hose to support the weight of the caliper.
      • Brake rotor
      • Anti-lock Brake System (ABS) sensor from the backing plate
      • Hub and bearing assembly from the backing plate
      • Hub and bearing assembly from the halfshaft
      • Hub and bearing assembly
    To Install:
    Exploded view of the front hub mounting and related components 7922xg36.gif

    1. Install or connect the following:
      • Hub and bearing assembly onto the halfshaft
      • Hub and bearing assembly to the backing plate. Torque the 3 bolts alternately and evenly to 70 ft. lbs. (95 Nm).
      • ABS sensor
      • Brake rotor
      • Caliper on the steering knuckle.
      • Halfshaft nut. Torque it to 118 ft. lbs. (160 Nm).
      • Front wheel. Torque the nuts to 100 ft. lbs. (140 Nm).

    Oct 18, 2010 | 2001 Oldsmobile Aurora

    1 Answer

    REMOVAL OF FRONT WHEEL BEARINGS


    Front (4 Wheel Drive) To Remove:
    1. Raise and support the vehicle
    2. Remove or disconnect the following:
      • Tire and wheel assembly
      • Rotor (See: Disc Brake Rotor)
      • Wheel speed sensor and brake hose mounting bracket bolt from the steering knuckle
      • Electrical connection for the wheel speed sensor
      • Front drive halfshaft assembly (See: Halfshaft)
      • Hub and bearing assembly mounting bolts 4WD front hub 9308kg35.gif

      • Hub and bearing assembly
    To Install:
    1. Clean all corrosion or contaminates from the steering knuckle bore and the hub and bearing assembly
    2. Lubricate the steering knuckle bore with wheel bearing grease or the equivalent
    3. Install or connect the following:
      • Hub and bearing assembly
      • Hub and bearing assembly mounting bolts and tighten the hub to knuckle bolts; Torque to: 133 ft. lbs. (180 Nm)
      • Front drive halfshaft assembly (See: Halfshaft)
      • Electrical connection for the wheel speed sensor
      • Wheel speed sensor and brake hose mounting bracket bolt to the steering knuckle and tighten the bolt; Torque to: 106 inch. lbs. (12 Nm)
      • Rotor (See: Disc Brake Rotor
      • Tire and wheel assembly
      Wheel lug nut tightening sequence gm_trk_sub15_wheel_lug_nut_tight_seq.gif

    4. Torque the lug nuts to specification
    5. Test drive the vehicle to confirm the repairs
    prev.gif next.gif

    Aug 03, 2010 | 2001 Chevrolet Silverado 1500

    1 Answer

    Replace front hub assembly.


    Replacing the front wheel bearing/hubs can be a big job for the inexperianced. Briefly...
    Remove tire/wheel
    Remove brake caliper assembly, do not remove brake line.
    Remove caliper bracket.
    Remove brake rotor.
    Unplug ABS sensor.
    Remove the large axle nut.
    Press axle out of bearing (may need special tool)
    Remove the 3 bearing bolts and remove bearing.

    May 19, 2010 | 2003 Chevrolet Impala

    3 Answers

    Replace front wheel bearing is it hard to do on 2002 alero


    its actually pretty easy if you have the basic tools needed and a little mechanical knowledge, because i dont think you can buy just the bearing at a auto parts store. they sell you the whole hub assembly which is great for the DIYer.

    lift the car off the ground and block it from rolling and place a jack stand under it so it cant fall on anyone.


    Wheel Bearings printpage_icon.gif

    Removal & Installation

    These vehicles are equipped with sealed hub and bearing assemblies. The hub and bearing assemblies are non-serviceable. If the assembly is damaged, the complete unit must be replaced.
    1. Before servicing the vehicle, refer to the precautions section.
    2. Remove or disconnect the following:
      WARNING DO NOT allow the caliper to hang unsupported from the brake hose.


      Front wheel Halfshaft nut and washer Caliper from the steering knuckle and support it aside


      Brake rotor Anti-lock Brake System (ABS) connector, if equipped 3 hub/bearing assembly bolts Halfshaft from the hub/bearing assembly Hub/bearing assembly

      0900c1528023b277.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Exploded view of the front hub/bearing assembly


    To install:
    Install or connect the following:

    Hub/bearing assembly onto the halfshaft, making sure the splines engage smoothly Hub/bearing assembly to the steering knuckle. Torque the bolts to 70 ft. lbs. (95 Nm). Anti-lock Brake System (ABS) connector, if equipped Brake rotor Caliper onto the steering knuckle. Torque the bolts to 38 ft. lbs. (51 Nm). Halfshaft nut. Torque the hub nut to 284 ft. lbs. (385 Nm) on nuts colored black, or 173 ft. lbs. (235 Nm) on gray colored nuts. Front wheel. Torque the nuts to 100 ft. lbs. (140 Nm).

    Jul 27, 2009 | 2004 Oldsmobile Alero

    1 Answer

    Directions replace front wheel bearings on a 1985 nissan stanza?


    996fb79.gif

    NOTE: After the wheel bearings have been removed or replaced or the front axle has been reassembled be sure to adjust wheel bearing preload. Refer to the Adjustment service procedure below. On the 1989–92 240SX there is just one wheel bearing, pressed into the hub and no adjusting cap. Refer to the exploded views of the Front Axle Hub Assembly. Review the complete service procedure.
    1. Raise and support the vehicle safely.
    2. Remove the front wheels and the brake caliper assemblies. NOTE: Brake hoses do not need to be disconnected from the brake caliper assemblies. Make sure the brake hoses are secure and do not let caliper assemblies hang unsupported from the vehicle.
    3. Work off center hub cap by using thin tool. If necessary tap around it with a soft hammer while removing.
    4. Pry off cotter pin and take out adjusting cap and wheel bearing lock nut.
    5. Remove wheel hub with disc brake rotor from spindle with bearings installed. Remove the outer bearing from the hub.
    6. Remove inner bearing and grease seal from hub using long brass drift pin or equivalent.
    7. If it is necessary to replace the bearing outer races, drive them out of the hub with a brass drift pin and mallet.
    8. Install the outer bearing race with a tool (KV401021S0 special tool number) until it seats in the hub flush. NOTE: Place a large glob of grease into the palm of one hand and push the bearing through it with a sliding motion. The grease must be forced through the side of the bearing and in between each roller. Continue until the grease begins to ooze out the other side through the gaps between the rollers. The bearing must be completely packed with grease.
    9. Pack each wheel bearing with high temperature wheel bearing grease. Pack hub and hub cap with the recommended wheel bearing grease up to shaded portions. Refer to the illustration.
    10. Install the inner bearing and grease seal in the proper position in the hub.
    11. Install the wheel hub with disc brake rotor to the spindle.
    12. Install the outer wheel bearing, lock washer, wheel bearing lock nut, adjusting cap, cotter pin (always use a new cotter pin and O-ring for installation after adjustment), spread cotter pin then install the O-ring and dust cap.
    13. Install the brake caliper assemblies and bleed brakes if necessary. Install the front wheels.

    Jun 23, 2009 | 1985 Nissan Stanza

    Not finding what you are looking for?
    1996 Ford Bronco Logo

    Related Topics:

    312 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    61249 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    Fordexpert

    Level 3 Expert

    5331 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...