Question about 1991 Ford Aerostar Extended

1 Answer

BUCKLE OF SEAT BELT IS NOT WORKING. iT WILL NOT LATCH ON TO THE TONGUE. iHAVE FOUND REPLACEMENT PART, BUT NEED TO KNOW HOW TO DISASSEMBLE/ASSEMBLE

Posted by on

1 Answer

I had the same problem with my driver side female side of the seatbelt assy. the screw(torx bolt) was seized.tried liquid wrench to no avail ,then used heat(propane torch) but be carefull the heat will traval across seat support to the chasis where the fuel line is and it may cause the plastic lines to melt causing a fire,so i used the heat with the assistance of a friend inside the vehicle to undo the screw and me underneath the vehicle with heat we were able to remove the screw.don't forget to protect the fuel lines from the heat (wet rags,or sheilded from any heat transfer)the danger is the feul lines r under pressurse

Posted on Aug 01, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2008 Ford Escape driver seat belt won't latch


replace the buckle
source from a wrecker /might be able to buy new not sure

Apr 29, 2016 | 2008 Ford Escape

1 Answer

Passenger seat belt warning stays on even with ignition off


Possible seatbelt latch problem. There are sensors in the latch part of the assembly that inform the restraint module as to what is happening. Sometimes foreign objects get stuck in the latch assemblies ( Children ) and can affect operation. Scanning the airbag module for codes will let you know what part of the restraint system is causing these lights to be on. As long as the airbag light remains on, the airbags will not deploy in the event of an accident

Jan 06, 2016 | Cadillac Cars & Trucks

1 Answer

Is there an air bag sensor in a seat belt?


Yes, one in the buckle assembly to notify the SRS when the buckle is latched and one in the retractor assembly .

Dec 28, 2013 | 2004 Pontiac Aztek

1 Answer

Broken seat belt buckle


If I had the problem I would look at a junkyard or on line at e-bay for a replacement. You will need to get the buckle and the belt that it is attached to that goes down to the floor down through the crack in the seat.
Remember the buckle receiver is made for the certain belt in the front and rear seats. I have often tried to put the wrong belt in a buckle and it would not fit. ( Example: the right belt goes in the right buckle.)
Be blessed.

Nov 08, 2013 | 2002 Nissan Xterra

1 Answer

Seat belt receiver


i've seen this before on car rear seats but not a truck but i guess it could happen as well the middle belt latch gets twisted/mixed up with the passenger side belt latch , mfg's use a different size belt for the middle passenger belt and it won't latch up with the passenger side belt reciever but does fit inside

ck that i'll bet thats it

Oct 20, 2013 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

1992 cadillac deville, driver's side seat belt


OK, I had the same problem with my 1990 Cadillac Deville. Had to go to a junk yard where they gave me the entire bolted on assembly. I got a 3/8" impact wrench and unbolted the belt buckle from the frame, and did the same to the one on the assembly they gave me. After that my buckle worked great. The color even matched the old one.

Jul 08, 2010 | 1992 Cadillac DeVille

1 Answer

My son stuck a small piece of foam into the seat belt latch assembly and buckled himself in. Now seat belt will not unlatch. How do I disassemble the latch unit to get the piece out?


Boys! If my 12 year old can't break it, it must be indestructable! I can't see a safe way to remove the plastic casing without breaking it or damaging the integrity of the buckel. I suggest that you use a shim to push the foam furter down into the buckle housing away from the internal latch. I just tried this on my toyota and used a 0.50mm feeler gauge (auto store) and was able to work around the front, back and sides of the release button down into the housing. It was stiff enough that I believe that anything in its way could be dislodged. I didn't want to replicate the foam jam, but I believe that with this shim I could dislodge the area around the latch hole enough to push the button and release. Then you can use tweezers and the shim to remove the foam. Good luck!

Mar 15, 2010 | 2007 Toyota Sienna

1 Answer

I have a suzuki swift 95 now the seat belt light


When you buckle the belt it will push a button inside the latch.
you need to replace the latch and it should go to working.

Jun 23, 2009 | 1991 Honda Accord

Not finding what you are looking for?
1991 Ford Aerostar Extended Logo

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

64034 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...