Question about 1990 Daihatsu Charade

1 Answer

Trying to fit G202 electronic ignition to G11 Charade. The G202 coil has blue/brown wire and black/blue. G202 distributor has black/brown wire and black. Can you tell me where these wires should go?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 98 Answers

The colour coded wires seem to differ at randomn. To identify the cables:

Dizzy:- use a multimeter set on ohms.. When you measure about 3 meg ohms, your red probe is on the +ve wire and the black probe is the signal to the coil.

For the coil, it hard to measure the primary resistance so the general convemtion is looking at the pins on the coil with the taper at the top, the +ve is on the right and the signal (coil -ve) is on the left. Sometimes you'll notice one of the wires on the coil is a thicker gauge, which is generally the +ve.

Posted on Sep 09, 2008

  • ChasDaihard Sep 09, 2008

    I should have added that your existing coil will not work, the ballast resistor becomes redundant and you need to tape off the fat black/white wire that currently goes to the coil +ve,

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

RPM meter is not working


check wiring going to the coil..
has it had a new coil fitted?
have you checked the electronic ignition?re-wire it from the rev guage backwards towards the coil.. replacing any old wiring is the way forward..

Jan 25, 2013 | 1988 Daihatsu Charade

Tip

ALARM, CRUISE CONTROL, and STEREO Wiring Color Codes for 1995 Honda Civic This...


ALARM, CRUISE CONTROL, and STEREO Wiring Color Codes for 1995 Honda Civic



This FixYa Tip is for the purpose of installing an Alarm, Remote Starter, Cruise Control, and / or Car Stereo into the vehicle listed in the subject line.


The wires listed are the ones you will need to successfully complete the task.


Some vehicles require additional relays and / or modules to bypass factory security. If they are required - it will be in the NOTES section below the wiring colors.


The following FixYa TIP is good for all Honda Civics for the following production years:


1995





STEREO WIRING COLOR CHART:

Constant 12V+: Blue/White
Switched 12V+: Yellow/Red
Ground: Black
Illumination: Red/Black
Dimmer: n/a
Antenna: Driver's Pillar

Front Speakers:
Left Front (+) Blue/Green
Left Front (-) Gray/Black
Right Front (+) Red/Green
Right Front (-) Brown/Black

Rear Speakers:
Left Rear (+) Blue/Yellow
Left Rear (-) Gray/White
Right Rear (+) Red/Yellow
Right Rear (-) Brown/White



NOTES: - none -

Additional Accessories:

Metra Brand Dash Kit: n/a
Metra Brand Wiring Harness: 70-1720
Metra Brand Antenna Adapter: n/a








ALARM / REMOTE START WIRING CHART:

Constant 12V+: White - Ignition Switch Harness
Starter: Black/White - Ignition Switch Harness
Ignition: Black/Yellow - Ignition Switch Harness
Accessory: Yellow - Ignition Switch Harness
Tach: Blue - Distributor
Brake Switch: Green/White - Brake Switch
Trunk Pin: Green/Black - (-) Above Fuse Panel (Blue Connector)
Parking Lights: Red/Black - (+) Above Fuse Panel
Head Lamp: Red/White - Steering Column
Hood Pin: n/a
Door Trigger: Light Green/Red - (-) Driver's Running board
Door Lock: Green/White - (-) 2 pin connector taped to blue connector behind fuse box
Door Unlock: Green/Red - (-) Driver's Door at Door Lock Module
Horn: Blue - Steering Column (Relay Required)
Windows UP: LF=Red/Blue RF=Blue/Yellow
Windows DOWM: LF=Red/Yellow RF=Blue/Green


NOTES: - none -






CRUISE CONTROL:

Constant 12V+: White - Ignition Switch Harness or Use Hot Side of Brake
Switched 12V+: Black/Yellow - Ignition Switch Harness
Ground: Use Chassis Near Cruise Control Module
Hot Side of Brake: n/a - Brake Switch
Cold Side of Brake: Green/White - Brake Switch
Tach: Blue - Distributor
VSS Wire : Yellow/Blue - Driver's Side Dash Footwell, Grey connector.




NOTES: 4000PPM

Vehicles with Manual Transmission require Clutch Switch.
Some vehicles may require a speed signal generator and/or other parts/adapters not listed above.
Rostra® Cruise Control module switch settings may differ if you use a speed signal generator or magnets and a pick up coil.


Thanks for using FixYa!! Please see my other tips on GPS, Car Audio, Large Appliances, and more.

on Apr 03, 2010 | Honda Civic Cars & Trucks

Tip

ALARM, CRUISE CONTROL, and STEREO Wiring Color Codes for 1994 Honda Civic This...


ALARM, CRUISE CONTROL, and STEREO Wiring Color Codes for 1994 Honda Civic



This FixYa Tip is for the purpose of installing an Alarm, Remote Starter, Cruise Control, and / or Car Stereo into the vehicle listed in the subject line.


The wires listed are the ones you will need to successfully complete the task.


Some vehicles require additional relays and / or modules to bypass factory security. If they are required - it will be in the NOTES section below the wiring colors.


The following FixYa TIP is good for all Honda Civics for the following production years:


1994





STEREO WIRING COLOR CHART:

Constant 12V+: Blue/White
Switched 12V+: Yellow/Red
Ground: Black
Illumination: Red/Black
Dimmer: n/a
Antenna: Driver's Pillar

Front Speakers:
Left Front (+) Blue/Green
Left Front (-) Gray/Black
Right Front (+) Red/Green
Right Front (-) Brown/Black

Rear Speakers:
Left Rear (+) Blue/Yellow
Left Rear (-) Gray/White
Right Rear (+) Red/Yellow
Right Rear (-) Brown/White



NOTES: - none -

Additional Accessories:

Metra Brand Dash Kit: n/a
Metra Brand Wiring Harness: 70-1720
Metra Brand Antenna Adapter: n/a








ALARM / REMOTE START WIRING CHART:

Constant 12V+: White - Ignition Switch Harness
Starter: Black/White - Ignition Switch Harness
Ignition: Black/Yellow - Ignition Switch Harness
Accessory: Yellow - Ignition Switch Harness
Tach: Blue - Distributor
Brake Switch: Green/White - Brake Switch
Trunk Pin: Green/Black - (-) Above Fuse Panel (Blue Connector)
Parking Lights: Red/Black - (+) Above Fuse Panel
Head Lamp: Red/White - Steering Column
Hood Pin: n/a
Door Trigger: Light Green/Red - (-) Driver's Running board
Door Lock: Green/White - (-) 2 pin connector taped to blue connector behind fuse box
Door Unlock: Green/Red - (-) Driver's Door at Door Lock Module
Horn: Blue - Steering Column (Relay Required)
Windows UP: LF=Red/Blue RF=Blue/Yellow
Windows DOWM: LF=Red/Yellow RF=Blue/Green


NOTES: - none -






CRUISE CONTROL:

Constant 12V+: White - Ignition Switch Harness or Use Hot Side of Brake
Switched 12V+: Black/Yellow - Ignition Switch Harness
Ground: Use Chassis Near Cruise Control Module
Hot Side of Brake: n/a - Brake Switch
Cold Side of Brake: Green/White - Brake Switch
Tach: Blue - Distributor
VSS Wire : Yellow/Blue - Driver's Side Dash Footwell, Grey connector.




NOTES: 4000PPM

Vehicles with Manual Transmission require Clutch Switch.
Some vehicles may require a speed signal generator and/or other parts/adapters not listed above.
Rostra® Cruise Control module switch settings may differ if you use a speed signal generator or magnets and a pick up coil.


Thanks for using FixYa!! Please see my other tips on GPS, Car Audio, Large Appliances, and more.

on Apr 01, 2010 | Honda Civic Cars & Trucks

1 Answer

Where can i get a wiring diagram for my 2002 chrysler neon auto


12V CONSTANT WIRE RED and PINK/BLACK Ignition harness
12V IGNITION WIRE DARK BLUE Ignition harness
12V ACCESSORY WIRE BLACK/ORANGE Ignition harness
STARTER WIRE YELLOW Ignition harness
PARKING LIGHTS (+) BLACK/YELLOW At Headlight switch
POWER DOOR LOCK (5-wire reverse polarity) ORANGE/PURPLE Harness Coming Into Vehicle From Driver's
Door
POWER DOOR UNLOCK (5-wire reverse
polarity)
PINK/PURPLE Harness Coming Into Vehicle From Driver's
Door
DOOR TRIGGER (-) YELLOW/BLACK At Headlight Switch
DOMELIGHT SUPERVISION (-) Use door trigger
TRUNK TRIGGER (-) GRAY/BLACK At Light In Trunk
TACHOMETER WIRE TAN/BLUE or BLACK/GRAY At Ignition Coil
BRAKE WIRE (+) WHITE/BROWN At Brake Pedal Switch
HORN TRIGGER (-) BLACK/RED Harness Coming From Steering Wheel At
Column
CAUTION! SRS airbag wires are not enclosed in protective loom at the steering column. They are a twisted pair of wires that run with rest of
ignition harness. Be careful not to cut or probe these wires.

Radio:

(Black plug)
Rear Right speaker -: Blue w/White stripe
Rear Left speaker -: Brown w/Yellow stripe
Front Right +: Purple
Front Left +: Dark Green
Rear Right speaker +: Blue w/Orange Stripe
Rear Left speaker +: Brown w/Blue Stripe
Power Antenna/Amp: White
(Gray Plug)
+12v battery wire: Pink or Pink w/White Stripe
+12v Ignition wire: Red w/ White Stripe
Front Right speaker -: Blue w/ Red Stripe
Front Left speaker -: Brown w/ Red Stripe

May 03, 2011 | 2002 Dodge Neon

2 Answers

Where is the ignition control module on an 1989 totota camry


Toyota Camry 1983-1996 Repair Guide Ignition Module - REMOVAL & INSTALLATION

External
All engines, except the 2S-ELC, have an external igniter.
  1. Turn the ignition key to the OFF position. Disconnect the negative battery cable.
  2. Separate the wiring harness connections.
  3. Unbolt the igniter.
  4. Loosen the nut holding the wire lead onto the coil.
  5. Tag and disconnect the wire lead.
  6. Lift the igniter off its mount.

To install:
  1. Mount the igniter to the bracket.
  2. Attach the wire lead to the coil.
  3. Connect the harness.
  4. Connect the negative battery cable. Reset any digital equipment such as radio memory and the clock if necessary.

Internal
REMOVING IGNITER WITH DISTRIBUTOR
See Figure 1
The internal igniter is only applicable to 2S-ELC engine Camry models. All other engines are equipped with an external igniter assembly.
Review the complete service procedure before this repair. Note position, color of wire and routing of all internal distributor assembly wiring.
  1. Disconnect the cable from the negative battery terminal.
  2. Remove the number one spark plug. Place a finger over the spark plug hole and rotate the crankshaft clockwise to top dead center. When there is pressure felt on the finger at the spark plug hole, this will be top dead center of the compression stroke on number one cylinder. If not, repeat the procedure. Install the number one spark plug.
  3. Mark the position of the distributor flange in relation to the camshaft housing. Remove the IIA distributor assembly.
  4. Remove the distributor cap with the wires attached, and remove the packing. Mark the position of the rotor relative to the housing and pull the rotor straight up and off the shaft. The distributor cap is held to the housing with three retaining screws.
  5. Remove the ignition coil dust cover.
  6. Remove the two nuts and spring washers and disconnect the four wires from the terminals on the side of the ignition coil. The wires are color coded yellow, blue, brown and red.
  7. Remove the four retaining screws and remove the ignition coil and packing.
  8. Remove the nuts and disconnect the pink, white and black wires from the igniter terminals. Remove the two igniter retaining screws and remove the igniter.

To install:
  1. Attach the new igniter with the two retaining screws. Connect the pink, black and white wires to their respective terminals and install the nuts. Make sure that the pick-up coil wires are secured in their clips and that there is slack in the wires.
  2. Install the ignition coil and attach it with the four retaining screws.
  3. Connect the four ignition coil wires to their respective terminals and install the two nuts and spring washers.
  4. Install the coil dust cover and push the rotor onto the shaft.
  5. Place the distributor cap and wires into position. Install and tighten the retaining screws.
  6. Install the distributor assembly and connect the negative battery cable.
  7. Connect a tachometer and timing light to the engine and adjust the ignition timing.

71948a0.jpg

Fig. 1: Make sure you remember where the colored wires attach for installation-2S-ELC engine
  1. Reset any digital equipment such as radio memory and the clock if necessary.

REMOVING IGNITER WITHOUT REMOVING DISTRIBUTOR
  1. Remove the distributor cap, rotor and di-electric insulator covers. Disconnect the red and yellow wires from the coil and the pink, white and black wires from the igniter.
  2. Remove the igniter. It may be necessary to mark and rotate the distributor to gain access to the igniter retaining screws. The timing should be checked after the distributor is returned to the mark.

To install:
  1. Install the new igniter using the two new retaining screws.
  2. Twist the pick-up coil wires together, install the white wire first then pink and black wires to their original locations. Make sure the wires do not touch the housing generator or advance plate.
  3. Route the red and yellow wires from the igniter so they do not contact moving parts. Connect the red wire to the right coil terminal (with the brown wire) and the yellow wire to the left terminal (with the blue wire). Replace the covers, rotor and cap.
  4. Connect a tachometer and timing light to the engine and adjust the ignition timing.

Hope this helped (remember comment and rated this).

Apr 05, 2010 | 1989 Toyota Camry

Tip

ALARM, CRUISE CONTROL, and STEREO Wiring Color Codes for 1993 Honda Civic This...


ALARM, CRUISE CONTROL, and STEREO Wiring Color Codes for 1993 Honda Civic

This FixYa Tip is for the purpose of installing an Alarm, Remote Starter, Cruise Control, and / or Car Stereo into the vehicle listed in the subject line.

The wires listed are the ones you will need to successfully complete the task.

Some vehicles require additional relays and / or modules to bypass factory security. If they are required - it will be in the NOTES section below the wiring colors.

The following FixYa TIP is good for all Honda Civics for the following production years:
1993


STEREO WIRING COLOR CHART:
Constant 12V+: White/Blue
Switched 12V+: Yellow/Red
Ground: Black
Illumination: Red/Black
Dimmer: n/a
Antenna: Driver's Pillar

Front Speakers:
Left Front (+) Blue/Green
Left Front (-) Gray/Black
Right Front (+) Red/Green
Right Front (-) Brown/Black

Rear Speakers:
Left Rear (+) Blue/Yellow
Left Rear (-) Gray/White
Right Rear (+) Red/Yellow
Right Rear (-) Brown/White

NOTES: - none -
Additional Accessories:
Metra Brand Dash Kit: n/a
Metra Brand Wiring Harness: 70-1720
Metra Brand Antenna Adapter: n/a




ALARM / REMOTE START WIRING CHART:
Constant 12V+: White - Ignition Switch Harness
Starter: Black/White - Ignition Switch Harness
Ignition: Black/Yellow - Ignition Switch Harness
Accessory: Yellow - Ignition Switch Harness
Tach: Blue - Distributor
Brake Switch: Green/White - Brake Switch
Trunk Pin: Green/Black - (-) Above Fuse Panel (Blue Connector)
Parking Lights: Red/Black - (+) Above Fus Panel (White Connector)
Head Lamp: Red/White - Steering Column
Hood Pin: n/a
Factory Disarm: Disarms with Unlock
Door Trigger: Green/Red - (-) Driver's Running board
Door Lock: Green/White - (-) Driver's Door at Door Lock Module
Door Unlock: Green/Red - (-) Driver's Door at Door Lock Module
Horn: Blue/Red - Steering Column (Relay Required)
Windows UP: LF=Red/Blue RF=Orange/White

NOTES: - none -



CRUISE CONTROL:
Constant 12V+: White - Ignition Switch Harness or Use Hot Side of Brake
Switched 12V+: Black/Yellow - Ignition Switch Harness
Ground: Use Chassis Near Cruise Control Module
Hot Side of Brake: n/a - Brake Switch
Cold Side of Brake: Green/White - Brake Switch
Tach: Blue - Distributor
VSS Wire : Yellow/Blue - Driver's Side Dash Footwell, Grey connector.


NOTES: 4000PPM
Vehicles with Manual Transmission require Clutch Switch.
Some vehicles may require a speed signal generator and/or other parts/adapters not listed above.
Rostra® Cruise Control module switch settings may differ if you use a speed signal generator or magnets and a pick up coil.

Thanks for using FixYa!! Please see my other tips on GPS, Car Audio, Large Appliances, and more.

on Apr 01, 2010 | Honda Civic Cars & Trucks

Tip

ALARM, CRUISE CONTROL, and STEREO Wiring Color Codes for 1992 Honda Civic This...


ALARM, CRUISE CONTROL, and STEREO Wiring Color Codes for 1992 Honda Civic

This FixYa Tip is for the purpose of installing an Alarm, Remote Starter, Cruise Control, and / or Car Stereo into the vehicle listed in the subject line.

The wires listed are the ones you will need to successfully complete the task.

Some vehicles require additional relays and / or modules to bypass factory security. If they are required - it will be in the NOTES section below the wiring colors.

The following FixYa TIP is good for all Honda Civics for the following production years:
1992


STEREO WIRING COLOR CHART:
Constant 12V+: Blue/White
Switched 12V+: Yellow/Red
Ground: Black
Illumination: Red/Black
Dimmer: n/a
Antenna: Driver's Pillar

Front Speakers:
Left Front (+) Blue/Green
Left Front (-) Gray/Black
Right Front (+) Red/Green
Right Front (-) Brown/Black

Rear Speakers:
Left Rear (+) Blue/Yellow
Left Rear (-) Gray/White
Right Rear (+) Red/Yellow
Right Rear (-) Brown/White

NOTES: - none -
Additional Accessories:
Metra Brand Dash Kit: n/a
Metra Brand Wiring Harness: 70-1720
Metra Brand Antenna Adapter: n/a




ALARM / REMOTE START WIRING CHART:
Constant 12V+: White - Ignition Switch Harness
Starter: Black/White - Ignition Switch Harness
Ignition: Black/Yellow - Ignition Switch Harness
Accessory: Yellow - Ignition Switch Harness
Tach: Blue - Distributor
Brake Switch: Green/White - Brake Switch
Trunk Pin: Green/Black - (-) Above Fuse Panel (Blue Connector)
Parking Lights: Red/Black - (+) Above Fus Panel (White Connector)
Head Lamp: Red/White - Steering Column
Hood Pin: n/a
Factory Disarm: Disarms with Unlock
Door Trigger: Green/Red - (-) Driver's Running board
Door Lock: Green/White - (-) Driver's Door at Door Lock Module
Door Unlock: Green/Red - (-) Driver's Door at Door Lock Module
Horn: Blue/Red - Steering Column (Relay Required)
Windows UP: LF=Red/Blue RF=Blue/Yellow
Windows DOWN: LF=Red/Yellow RF=Blue/Green
NOTES: - none -



CRUISE CONTROL:
Constant 12V+: White - Ignition Switch Harness or Use Hot Side of Brake
Switched 12V+: Black/Yellow - Ignition Switch Harness
Ground: Use Chassis Near Cruise Control Module
Hot Side of Brake: n/a - Brake Switch
Cold Side of Brake: Green/White - Brake Switch
Tach: Blue - Distributor
VSS Wire : Yellow/Red - Driver's Side Dash Footwell, Grey connector.


NOTES: 4000PPM
Vehicles with Manual Transmission require Clutch Switch.
Some vehicles may require a speed signal generator and/or other parts/adapters not listed above.
Rostra® Cruise Control module switch settings may differ if you use a speed signal generator or magnets and a pick up coil.

Thanks for using FixYa!! Please see my other tips on GPS, Car Audio, Large Appliances, and more.

on Apr 01, 2010 | Honda Civic Cars & Trucks

2 Answers

Size of Jets for 1984 Daihatsu Charade G11 Turbo Carburettor


You won't need to change the jets. We have had the Cb60 pumping 75- 90kW on the stock carby. Are you trying to increase performance there are better ways: e.g. RHF5 series turbo, lightened flywheel (4.5kg) with Mazda 121 clutch plate and 1600lb pressure plate. Swap in a G202 electronic dizzy& coil, and replace vacuum advance diaphragm.

Carby hat looks like this:





Feb 18, 2009 | 1988 Daihatsu Charade

Tip

ALARM, CRUISE CONTROL, and STEREO Wiring Color Codes for 1988 - 1991 Honda Civic...


ALARM, CRUISE CONTROL, and STEREO Wiring Color Codes for 1988 - 1991 Honda Civic

This FixYa Tip is for the purpose of installing an Alarm, Remote Starter, Cruise Control, and / or Car Stereo into the vehicle listed in the subject line.

The wires listed are the ones you will need to successfully complete the task.

Some vehicles require additional relays and / or modules to bypass factory security. If they are required - it will be in the NOTES section below the wiring colors.

The following FixYa TIP is good for all Honda Civics for the following production years:
1988
1989
1990
1991


STEREO WIRING COLOR CHART:
Constant 12V+: White/Blue
Switched 12V+: Yellow/Red
Ground: Black
Illumination: Red/Black
Dimmer: n/a
Antenna: Driver's Pillar

Front Speakers:
Left Front (+) Blue/Green
Left Front (-) Gray/Black
Right Front (+) Red/Green
Right Front (-) Brown/Black

Rear Speakers:
Left Rear (+) Blue/Yellow
Left Rear (-) Gray/White
Right Rear (+) Red/Yellow
Right Rear (-) Brown/White

NOTES: - none -
Additional Accessories:
Metra Brand Dash Kit: n/a
Metra Brand Wiring Harness: 70-1720
Metra Brand Antenna Adapter: n/a




ALARM / REMOTE START WIRING CHART:
Constant 12V+: White - Ignition Switch Harness
Starter: Black/White - Ignition Switch Harness
Ignition: Black/Yellow - Ignition Switch Harness
Accessory: Blue/White - Ignition Switch Harness
Tach: Blue - Distributor
Brake Switch: Green/White - Brake Switch
Trunk Pin: Green/Black - (-) Harness from Dash Indicator
Parking Lights: Red/Black - (+) Fuse Panel
Hood Pin: n/a
Factory Disarm: n/a
Door Trigger: Green/Red - (-) Driver's Kick Panel
Door Lock: Green/White - (-) Driver's Door at Door Lock Module
Door Unlock: Green/Red - (-) Driver's Door at Door Lock Module
Horn: Blue/Red - Steering Column (Relay Required)

NOTES: - none -



CRUISE CONTROL:
Constant 12V+: White - Ignition Switch Harness or Use Hot Side of Brake
Switched 12V+: Black/Yellow - Ignition Switch Harness
Ground: Use Chassis Near Cruise Control Module
Hot Side of Brake: n/a - Brake Switch
Cold Side of Brake: Green/White - Brake Switch
Tach: Blue - Distributor
VSS Wire : Yellow/Red - Driver's Side Dash Footwell, 13-pin connector.


NOTES: 4000PPM
Vehicles with Manual Transmission require Clutch Switch.
Some vehicles may require a speed signal generator and/or other parts/adapters not listed above.
Rostra® Cruise Control module switch settings may differ if you use a speed signal generator or magnets and a pick up coil.

Thanks for using FixYa!! Please see my other tips on GPS, Car Audio, Large Appliances, and more.

on Apr 01, 2010 | Honda Civic Cars & Trucks

Not finding what you are looking for?
1990 Daihatsu Charade Logo

341 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daihatsu Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

60960 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Daihatsu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...