Question about Nissan Quest

1 Answer

#3 cyl dead at idle picks up after rpm 2000 and up

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 19 Answers

Hi there,
I suspect an air leak at the manifold or maybe even a burnt out valve, i would do a compression check to start with and go from there, if the compression is ok then look for air leaks around manifold or prehaps vacuum hoses including booster hose.
I hope this helps you,

Posted on Jul 30, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi I have a Mazda etude 1.6 ie I replaced the timing belt and nu it don't wane pick up any revs the timing is correctly set the.valve is ok.it idles well on 2000 revs but when i pres the gas it dies


not a Mazda man but 2000 rpm's at idle is more than double what it should be . My toyota idles at about 750 .runs 2000 going 70 mph down the highway

Jul 30, 2015 | Mazda Cars & Trucks

1 Answer

What is the good idling for a car driving at 40mph? Because it idles at 2000 rpm's and I think thats a little high? the car is 97 toyota camry 4 cyl 2.2. Also after I stop it has a certain smell. Good...


A car cannot idle when you are driving, the term "idle" is only used when the car is stopped and motionless. You mean the the car's RPM's are at 2000 when driving at 40mph. The RPM's are normal at that speed and you cannot change it unless you change the gear ratios inside your Transaxle.

The smell you are referring to may be a oil leak of some sort, you may need to look on the ground after you are parked awhile and see if there is fluid leaking and try to determine what type of fluid it is so you can trace what component is leaking.

Apr 29, 2011 | 1997 Toyota Camry

2 Answers

It runs rough sometimes it dies, I have tuned it up , plugs dist cap, wires rotor the computer , It has very poor gas milage .it has a 2300 with automatic trans,


have the intake gasket checked. spray carb/choke cleaner around intake gasket and if rpms change then you have a bad gasket which causes rough idle bad fuel econ

Apr 09, 2011 | Ford Ranger Cars & Trucks

1 Answer

Voltage at battery at idle is 11.9 and at2000rpm it isover 14 volts.lights brighten and heater fan motor speed picks up considerably as rpms pick up from idle to 2000 rpm and on up.load tested battery and...


Did you check the voltage after a drive or after it was jumped. The battery may need some time to recharge if it was jumped before it gets checked. Have you checked for a possible draw on the battery? This could be a reason it dies every once in a while. I think that the Alternater is on its way out, it doesn't sound like it is charging like it should. It the new belt tight enough(some new belts stretch after a short time)

Jan 27, 2011 | 1998 Suzuki Sidekick

1 Answer

2000 Chevy s10 2.2L very rough idle at low rpm


run a fuel pressure test, if that checks out fine it may be a faulty coil pack or ignition control module

Jul 28, 2009 | 2000 Chevrolet S-10

1 Answer

How do i set the timming on 94 mercury villager van


you only set base timing to 15 degrees BTDC (before top dead center).

Ignition Timing
  1. s1v~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Parking brake control should be applied.
    Depress the parking brake pedal, and warm the engine to the normal operating temperature.
  1. Turn off all electrical loads.
  1. Rev the engine to 2000-3000 rpm two or three times and allow the engine to return to the idle.
  1. Turn off the engine and disconnect the throttle position sensor electrical connector. (not really necessary)
  1. Start the engine and rev it to 2000-3000 rpm two or three times and allow the engine to return to the idle.
  1. Check the idle speed. The idle speed should be between 700-800 rpm in PARK (P) or NEUTRAL (N) position.
  1. NOTE: Make sure that the timing pointer is pointing to the 15° Before Top Dead Center (BTDC) mark on the crankshaft pulley. Each notch on the crankshaft pulley represents 5 degrees.
    Check the ignition timing with a timing light.
632206b.gif go here for villager help

http://autos.groups.yahoo.com/group/villagerquest/

Jun 09, 2009 | 2001 Mercury Villager

2 Answers

Rough and noisy idle


i have a 2000 kia sportage the timing belt broke and the 2.0 is a zero clearance motor.you need to find out if it bent the valves.it did in mine.

Aug 24, 2008 | 2000 Kia Sportage

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

64052 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...