Question about 1998 Subaru Impreza

1 Answer

Doing a brake job all 4 - 1998 Subaru Impreza

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

How to replace knock sensor 1998 2.2 subaru impreza

Posted on Nov 24, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My abs, traction, and brake lights are on after a front brake and bearing job were done


By "were done" I am guessing someone else did the job for you. It is a common error at garages to forget to reconnect the sensors so that is my first thought but then you say you changed the front sensors, was that after the brake job and do you have 4 wheel ABS? The plugs for the sensors should always be cleaned if not replaced after a brake job in my opinion (high dirt area). More info will get you a better answer if you post back I may be able to help more/better.

Mar 26, 2014 | 2011 Ford Focus

1 Answer

Do you have to take the hub off on a brake job for a avalanche 2003 4 wheel drive


To do a brake job front or rear there is no need to remove the "hubs" the front and rear rotors or rear drums are knock offs. if they are stuck to the hub a couple of gentle hits with a hammer will usually free them up. If you are replacing the rotors than whack away as hard as you would like.

Mar 14, 2012 | 2003 Chevrolet Avalanche

1 Answer

How to get the rear brake piston compressed properly on a 2006 ford 500.


You push the rear caliper piston in by hand

On the front you can use an old pad &
4" c-clamp,not so on the rear

It will go back in, if you open the bleeder valve

You have to flush all 4 corners, on all your vehicles,
every 2 years anyway. Didn't know that -right !

Now to your part of the puzzle

Buy a small tool at parts store that looks like a
1 1/4" cube with pins on it

That is to turn in the caliper parking brake feature
inside & behind the pistion you where trying to push on

Push in by hand while turning clockwise with the cube
using a 3/8" extension & ratchet

Once the pads are on ratchet up the parking brake
lever by hand

Now your changing your brake fluids every 2 years
you start doing the power steering & trans EVERY
30,000 Miles,ALWAYS on ALL Vehicles

Sand off ALL rust on caliper & pad abutements &
sliding surfaces & use anti-seize ,or you may as well
not do the job in the first place. The pro don't do that,
but you can do a nice job, so the brakes actually work

Jun 25, 2011 | Ford Five Hundred Cars & Trucks

1 Answer

2006 lacrosse brake job estimate


If your car needs rotors and pads front and rear , a shop will charge between 4-600 for complete brake job.

May 03, 2011 | 2006 Buick LaCrosse

1 Answer

Abs light on anf off after rear brake job. Today


Not a booster problem. what bad noises? abs problmes wont make noises, unless its the pump operating. ck the mushy pedal, that will maybe fix all problems. I dont think its related to the 2/4wd lights?

Jul 23, 2010 | 2000 GMC Jimmy

1 Answer

What parts do I need to do a complete brake job on a 1998 Ford Thunderbird...front and back


1. Machine or replace rotors and/or Drums
2. New Disc Pads and /or Brake Shoes & springs for brake shoes
3. New or recond Brake Booster
4. New or recond Master Cylinder
5. New or recond Disc brake calipers and/or wheel Cylinders
6. Brake fluid
7. Check all the brake fluid lines for any damage
thats about all I can think of, hope it helps

Jun 18, 2010 | 1998 Ford Thunderbird

2 Answers

I have brake fluid leaking from back passenger wheele right from the back onto the tire..is this a costly repair? is there any thing i can do to fix it my self


No, it won't be costly. It's just the brake cylinder leaking. You will need to buy a new one. You will have to pull the wheel off, and take the brake drum off. Undo the brake line from the back of the cylinder. Remove the two bolts that hold it in place, and replace it witht he new one.

Dec 29, 2009 | 1994 Dodge Caravan

1 Answer

Leaking brake line over hub of rear rusted


If you want to fix this yourself, you will need to first determine what size brake line you require. It is usually either 3/16" or 1/4". You can purchase the brake line at most autoparts stores. It will come in five foot sections. You will need enought brake line for the job and most likely a compression fitting. This job will require a tubing cutter, flairing tool, and tubing bender. Not really a hard job, you can do it!! Good luck and hope this helps.

Jul 15, 2009 | 1999 Ford Explorer

2 Answers

Brake light on dash won't turn off.


I just had my brakes done (all 4 rotors replaced and brake shoes) on my 99 Camry, and when I took it for a test drive, the Brake light was on. The way I got rid of it was by disconnecting the battery for a minute or 2. It reset whatever was causing it to stay on.

Hope this helps.

Ed

Apr 14, 2009 | Toyota Avalon Cars & Trucks

1 Answer

Brake job


A brake job is something that is done properly and I've seen so many bad brake jobs in my time. I know it is rather expensive to get a brake job done but to do it yourself one has to be very carefull that it is done right. New rotors are about 30 dollars each and then there are the seals and rotors that have to be serviced properly. Needlessly to do the whole brake job would be quite a job for you if you haven't done it before.

Feb 12, 2009 | 2002 Toyota ECHO

Not finding what you are looking for?
1998 Subaru Impreza Logo

Related Topics:

176 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...