Question about 2000 Toyota ECHO

1 Answer

Remove and replace belts - 2000 Toyota ECHO

Posted by on

  • jmart22r Oct 19, 2008

    96 toyota tacoma

  • Anonymous Nov 07, 2008

    Started but dont know how to relese the tension off the old belts

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Losen the top and bottom bolts on the alternator and tilt or rotate the alternator up (top goes backwards) to losen the top serpentine belt. Once there is slack, remove the belt (don't forget to take note of the routing of the original belt.

Posted on Mar 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 xl7. How can I adjust alternator?


remove battery neg lug first. do not yank off alternator wires! until
this step is done first, or boom fire or eat acid.

which engine, we cant guess them here.
my guess H27 v6, wrong the 3.6L


all belts covered on car. (accessory)

here is a real 2007 page
seem you get lost at step 7
right>?


26044119-eqsv1nhxqdz21u4tq0h4adgz-1-0.jpg the alternator is NOT adjustable
so why ask this?
the $4 FSM covers this.
under drive belt replacement.
Drive Belt Replacement


Removal Procedure

Remove the air cleaner assembly. Refer to Air Cleaner Assembly Replacement .

Install the engine support fixture. Refer to Engine Support Fixture .

Remove the engine mount strut bracket. Refer to Engine Mount Strut Bracket Replacement - Right Side .

Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .

Remove the engine splash shield. Refer to Engine Splash Shield Replacement - Right Side .

Remove the right side engine mount bracket. Refer to Engine Mount Bracket Replacement - Right Side .

Lower the vehicle.


Rotate the drive belt tensioner clockwise to release the drive belt tension.

Slide the drive belt off of the belt idler pulley (1).

Slowly release the drive belt tensioner.

Remove the drive belt from the accessory drive pulleys.
if the post was to remove alternator? is it
do above
then unbolt alt.
end guessing what you are doing....


26044119-eqsv1nhxqdz21u4tq0h4adgz-1-1.jpg

Jan 08, 2016 | Suzuki Cars & Trucks

2 Answers

1998 Isuzu trooper 3.5 alternator replace


step one remove battery neg lug .
the above video (of book?) is wrong.
the belt tension-ing step was skipped.

remove belt steps remove alt. wiring. remove alternator (bolts) it falls free. replace it , reverse steps above belt back tension belt. battery cable back. test run. charge/BAT lamp off?
see wrench below, turn it CW.
this releases the spring tension and belt comes off
to put back, do same and put on belt and release wrench.

25186758-dk3xh54xw1fmpqbxyhqoyzal-4-0.jpg3.5L only. USA only.

Oct 05, 2014 | Isuzu Trooper Cars & Trucks

1 Answer

How to remove belts from 1994 dodge caravan 2.5 liter


Drive Belts

Print


INSPECTION

See Figures 1, 2, 3, 4 and 5
Check the condition and tension of all drive belts every 12,000 miles, or at least once a year. Loose drive belts can lead to poor engine cooling and diminished alternator, power steering pump, air conditioning compressor, or emission air pump output. A belt that is too tight places a strain on the bearings in the driven component.


0900c15280215ae4.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 1: There are typically 3 types of accessory drive belts found on vehicles today


0900c15280215ae5.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 2: An example of a healthy drive belt


0900c15280215ae6.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 3: Deep cracks in this belt will cause flex, building up heat that will eventually lead to belt failure


0900c15280215ae7.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 4: The cover of this belt is worn, exposing the critical reinforcing cords to excessive wear


0900c15280215ae8.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 5: Installing too wide a belt can result in serious belt wear and/or breakage
Replace any drive belt that is glazed, worn, cracked, or stretched to the point where correct adjustment tension is impossible. If two belts are used to drive a component, always replace both belts when replacement is necessary. After installing a new belt, run the engine for ten minutes, shut OFF the engine and recheck the belt tension. Readjust if necessary.


ADJUSTMENT

See Figures 6, 7, 8, 9 and 10


0900c15280215ae9.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 6: Engine belt tension chart-2.2L engines


0900c15280215aea.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 7: Engine belt tension chart-1987-89 2.5L engines


0900c15280215aeb.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 8: Engine belt tension chart-2.6L engines


0900c15280215aec.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 9: Engine belt tension chart-1990-93 models


0900c15280215aed.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 10: Engine belt tension chart-1994-95 models
Two popular methods of checking drive belt adjustment are; the Belt Tension Gauge Method and the Belt Deflection Method. The former requires a special gauge and the latter requires a straight edge and scale or just a good eye for measurement. The deflection method will be used in the following belt replacement instructions. A rule of thumb for checking belt tension by the deflection method is to determine the midpoint between two pulleys of the drive belt and press down at that point with moderate thumb pressure. The belt should deflect to the measurement indicated in the following installation procedures. Adjustment is necessary if the belt is either too loose or too tight.

WARNING A belt adjustment which is either too loose or too tight will eventually damage the accessory that belt is driving. A too loose adjustment allows free-play in the belt which could transfer a whipping motion or shock to the accessory drive pulley. Similarly, a belt which is too tight will preload the accessory bearings, leading to early failure.


REMOVAL & INSTALLATION

See Figure 11
Raise the front of the vehicle, support on jackstands and remove the lower splash shield if access is hampered due to space limitations when changing drive belts.


0900c15280215aee.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 11: Support the vehicle, then remove the lower right side splash shield for access to the drive belts
2.2L Engines
A/C COMPRESSOR DRIVE BELT
See Figures 12, 13 and 14


0900c15280215aef.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 12: A/C compressor drive belt adjusting points-2.2L engines


0900c15280215af0.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 13: Loosening the locking screws for A/C compressor drive belt removal


0900c15280215af1.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 14: Removing the A/C compressor drive belt from under the vehicle

  1. Loosen the idler pulley bracket pivot screw and the locking screw.
  2. Remove the belt and install a replacement.
  3. Using a breaker bar and socket apply torque to the welded nut provided on the mounted bracket to obtain proper tension.
  4. Tighten the locking screw first, followed by pivot screw. Tighten to 40 ft. lbs. (55 Nm).

ALTERNATOR DRIVE BELT (CHRYSLER TYPE)
See Figures 15 and 16


0900c15280215af2.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 15: Alternator belt adjustment-2.2L engine


0900c15280215af3.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 16: Loosening the locking screw for alternator drive belt removal
If removal of the alternator belt is required, the A/C belt must first be removed.

  1. Loosen the pivot nut, locking screw, and the adjusting screw.
  2. Remove the belt and install a replacement.
  3. Adjust to specification by tightening the adjusting screw.
  4. Tighten the locking screw to 25 ft. lbs. (34 Nm).
  5. Tighten the pivot nut to 30 ft. lbs. (41 Nm).

ALTERNATOR DRIVE BELT (BOSCH TYPE)
If removal of the alternator belt is required, the A/C belt must first be removed.
  1. Loosen the pivot nut, locking nut, and adjusting screw.
  2. Remove the belt and install a replacement.
  3. Adjust to specification by tightening the adjusting screw.
  4. Tighten the locking nut to 25 ft. lbs. (34 Nm).
  5. Tighten the pivot nut to 30 ft. lbs. (41 Nm).

POWER STEERING BELT
If removal of the power steering belt is required, the A/C and alternator belts must first be removed.
  1. Loosen the locking screw, and pivot screw.
  2. Remove the belt and install a replacement.
  3. Install a 1 / 2 in. breaker bar into the pump bracket slot, apply pressure with the breaker bar and adjust the belt to specification.
  4. Tighten the locking screw first, then the pivot screw. Tighten to 40 ft. lbs. (55 Nm).

AIR PUMP DRIVE BELT
See Figure 17


0900c15280215af5.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 17: Air pump belt adjustment-2.2L engines
When servicing the air pump, use the square holes provided in the pulley to prevent camshaft rotation.

  1. Remove the nuts and bolts retaining the drive pulley cover.
  2. Remove the locking bolt and pivot bolt from the pump bracket, then remove the pump.
  3. Remove the belt and install a replacement.
  4. Position the pump, then install the locking bolt and pivot bolt finger-tight.
  5. Install a 1 / 2 in. breaker bar into the bracket assembly (block the drive pulley to prevent camshaft rotation), and adjust the belt to specification.
  6. Tighten locking bolt and pivot bolt to 25 ft. lbs. (35 Nm).

2.5L Engines
AIR CONDITIONING COMPRESSOR
See Figure 18


0900c15280215af8.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 18: Drive belt adjustment points-2.5L engines

  1. Loosen the idler bracket pivot screw and the locking screws to replace, or adjust belt.
  2. Remove the belt and install a replacement.
  3. Adjust the belt to specification by applying torque to weld nut on the idler bracket.
  4. Tighten locking screw first, followed by the pivot screw. Tighten to 40 ft. lbs. (55 Nm).

ALTERNATOR BELT
See Figure 18
If replacement of the alternator belt is required, the A/C drive belt must first be removed.
  1. Loosen the pivot nut, locking nut, and adjusting screw.
  2. Remove the belt and install a replacement.
  3. Adjust the belt to specification by tightening the adjusting screw.
  4. Tighten the locking nut to 25 ft. lbs. (35 Nm).
  5. Tighten the pivot nut to 30 ft. lbs. (40 Nm).

POWER STEERING PUMP
See Figure 18
If replacement of the power steering belt is required, the A/C and alternator belts must first be remove.
  1. Loosen the locking screw and pivot screw to replace, or adjust the belt.
  2. Remove the belt and install a replacement.
  3. Using a 1 / 2 in. breaker bar positioned in adjusting bracket slot, adjust the belt to specification.
  4. Tighten the locking screw followed by the pivot screw. Tighten to 40 ft. lbs. (55 Nm).

2.6L Engines
ALTERNATOR/AIR CONDITIONING COMPRESSOR BELT
See Figure 19


0900c15280215af9.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 19: Drive belt adjustment points-2.6L engines

  1. Loosen the locking screw, jam nut, and pivot nut.
  2. Loosen the adjusting screw.
  3. Remove the belt and install a replacement.
  4. Adjust the belt to specification by tightening the adjusting screw.
  5. Tighten the locking screw followed by the pivot nut. Tighten to 16 ft. lbs. (22 Nm).
  6. Tighten the jam nut to 21 ft. lbs. (28 Nm).

POWER STEERING PUMP BELT
See Figure 19
If replacement of the power steering belt is required, the alternator and A/C belt must first be remove.
  1. Loosen the pivot screw, and the locking screw.
  2. Remove the timing pickup.
  3. Remove the belt and install a replacement.
  4. Install a 1 / 2 in. breaker bar in the adjusting bracket slot, torque to specification.
  5. Tighten the locking screw, followed by the pivot screw. Tighten to 40 ft. lbs. (55 Nm).
  6. Install the timing pick-up, and tighten to 160 inch lbs. (18 Nm).

Jul 26, 2012 | 1994 Dodge Grand Caravan

1 Answer

Timing belt replacement


Disconnect negative battery cable. Disconnect power
steering reservoir, and remove reservoir bracket.
Disconnect wire harness bracket for Data Link Conne
ctor No. 1. Remove generator and generator bracket.


Remove ABS actuator. Raise and support vehicle. Rem
ove right front wheel. Remove right engine
undercover. Remove power steering drive belt. Sligh
tly jack up engine and remove right engine mounting

insulator.

Remove spark plugs. Remove crankshaft pulley. . Remove right engine mounting bracket.
Remove No. 2 timing belt cover. . Temporarily install crankshaft pulley with pulle
y bolt. Set No.
1 cylinder to TDC on compression stroke. .

Loosen mounting bolt of No. 1 idler pulley and shif
t pulley toward left as far as it will go to reliev
e belt
tension. . Temporarily tighten idler pulley. Remove cranksh
aft pulley and No. 1 timing belt
cover.

If reusing timing belt, mark direction of rotation
on belt. Also place match marks on belt and camshaf
t
pulley. . Remove timing belt from engine.

NOTE:Always turn crankshaft clockwise.

Mar 18, 2010 | 1997 Toyota RAV4

1 Answer

Cant find 97 ford taurus serpentine belt diagram


Drive Belt Replacement ani_caut.gif WARNING: IF EQUIPPED, DO NOT ALLOW DRIVE BELT TENSIONER (6B209) TO SNAP BACK AS DAMAGE TO DRIVE BELT TENSIONER OR PERSONAL INJURY COULD RESULT.
NOTE: Minor cracks in the V-grooved portion of the serpentine drive belt (8620) are considered normal and acceptable. If the drive belt has chunks missing from the ribs, the drive belt should be replaced.

NOTE: Conditions requiring drive belt replacement are excessive wear, rib chunk-out, severe glazing, frayed cords or other conditions. Replace any drive belt exhibiting any of these conditions.

NOTE: When installing drive belt on pulley, make sure that all V-grooves make proper contact with pulleys.



q1834c.gif

Drive Belt, Serpentine—Except SHO
Removal
  1. ani_caut.gif WARNING: USE CAUTION WHEN REMOVING OR INSTALLING DRIVE BELT TO MAKE SURE THAT TOOL DOES NOT SLIP FROM DRIVE BELT TENSIONER OR PERSONAL INJURY AND/OR DAMAGE TO DRIVE BELT TENSIONER AND DRIVE BELT MAY OCCUR.
    Using a 15 mm socket or wrench on bolt attaching drive belt tensioner pulley, rotate drive belt tensioner clockwise on 3.0L (2V) and 3.0L (2V) FF, rotate the drive belt tensioner counter clockwise on 3.0L (4V) to remove drive belt from pulleys. Make sure spring keeper engages into slot.


    Drive Belt Tensioner—3.0L (4V)


    q3759a.gif

Installation
  1. Install drive belt over all pulleys (except drive belt tensioner).
  1. Rotate drive belt tensioner as described under the removal procedure and install drive belt over drive belt tensioner pulley. Make sure that all V-grooves make proper contact with pulleys. Make sure spring keeper releases or improper belt tension will occur.


    Pulley, Routing—Accessory Drive Belt 3.0L (2V)/3.0L (2V) FF Engine


    q3244d.gif


    Item Part Number Description 1 10300 Generator 2 6C348 Idler Pulley 3 3A674 Power Steering Pump 4 19703 A/C Compressor 5 6312 Crankshaft Pulley 6 6B209 Drive Belt Tensioner 7 8501 Water Pump 8 8620 Drive Belt

    Pulley, Routing—Accessory Drive Belt 3.0L (4V)


    q3735a.gif


    Item Part Number Description 1 3A674 Power Steering Pump 2 8501 Water Pump 3 19703 A/C Compressor 4 8620 Drive Belt 5 6312 Crankshaft Pulley 6 6B209 Drive Belt Tensioner 7 10300 Generator
3.4L SHO Engine
Removal
  1. Remove the right front wheel and tire assembly. For additional information, refer to Section 04-04.
  1. Remove the inner fender splash shield.
  1. Remove the alternator shield.
  1. ani_caut.gif WARNING: USE CAUTION WHEN REMOVING OR INSTALLING DRIVE BELT TO MAKE SURE WRENCH DOES NOT SLIP FROMDRIVE BELT TENSIONER OR POSSIBLE PERSONAL INJURY AND/OR DAMAGE TO DRIVE BELT TENSIONER AND DRIVE BELT MAY OCCUR.
    Using a 3/8 inch ratchet on the lifting lug, rotate drive belt tensioner counterclockwise (upward) and engage spring keeper. Remove drive belt from drive belt tensioner.
  1. Lower vehicle.
  1. Remove drive belt.
Installation
  1. Install drive belt over all pulleys (except drive belt tensioner ).
  1. Raise vehicle on hoist.
  1. Rotate drive belt tensioner , as described under Removal procedure and install drive belt over drive belt tensioner pulley. Make sure all V-grooves make proper contact with pulleys. Make sure the spring keeper is released or improper belt tension will occur.
  1. Install the alternator shield.
  1. Install the inner fender splash shield.
  1. Install the wheel and tire assembly. For additional information, refer to Section 04-04.


    Pulley Routing—Accessory Drive Belt, 3.4L SHO


    q3736a.gif


    Item Part Number Description 1 3A733 Power Steering Pump Pulley 2 6B217 (RH) Idler Pulley 3 19703 A/C Compressor 4 8620 Drive Belt 5 6312 Crankshaft Pulley 6 6B209 Drive Belt Tensioner 7 10346 Generator 8 6B217 (LH) Idler Pulley 9 6B217 (Center) Idler Pulley
Drive Belt, Water Pump
Removal
  1. NOTE: If removal of the water pump drive pulley is required, refer to Section 03-03.

    Rotate drive belt tensioner clockwise by hand and remove drive belt from drive belt tensioner .
  1. Remove drive belt from water pump drive pulley and water pump pulley.
Installation
  1. Position drive belt onto water pump drive pulley and water pump pulley.
  1. Rotate drive belt tensioner clockwise by hand and install drive belt over top of drive belt tensioner pulley. Make sure all V-grooves make proper contact with pulleys.


    Pulley Routing—Water Pump Drive Belt


    q3737a.gif


    Item Part Number Description 1 6B209 Drive Belt Tensioner 2 6A312 Crankshaft Pulley 3 8501 Water Pump 4 8620 Drive Belt

Jun 01, 2009 | 1997 Ford Taurus

1 Answer

Need to replace belt tensioner pulley


no remove the belt remembering the belt on how it went on remove belt then remove the tensioner usually one bolt and replace tensioner then replace belt the same way it came off

Mar 27, 2009 | 1996 Mercury Sable

1 Answer

Replacing the tension belts on the reFord windstar 1998.


FOR COMPLETE Diagram Of this Procedure and Belt Routing Email Me@rejakwilsoon@aol.com and I will Send DETAILED PICTURE and Instructions


NOTE:
  • Minor cracks in the V-grooved portion of the serpentine drive belt are considered normal and acceptable. If the drive belt has chunks missing from the ribs, the drive belt should be replaced.
  • When installing drive belts on pulley, make sure that all V-grooves make proper contact with accessory pulleys.
Conditions requiring drive belt replacement are excessive wear, rib chunkout, severe glazing, frayed cords, etc. Replace any drive belt that exhibits any of these conditions.

REMOVAL
  1. Using a 15 mm socket or wrench attached on drive belt tensioner pulley bolt. Rotate drive belt tensioner clockwise to remove drive belt from pulleys. WARNING: USE CAUTION WHEN REMOVING OR INSTALLING DRIVE BELT TO MAKE SURE THAT TOOL DOES NOT SLIP.
INSTALLATION
  1. Install drive belt over all accessory pulleys (except drive belt tensioner).Rotate drive belt tensioner as described under Removal to install drive belt over drive belt tensioner pulley. Make sure that all V-grooves make proper contact with pulleys

Feb 10, 2009 | 1998 Ford Windstar

2 Answers

I need instructions on replacing the timing belt


1. Remove the Alternator Belt.
2. Remove the Water Pump Pulley
3. Remove the Air Conditioner Belt and Power Steering Belt.
4. Remove the Crankshaft Pulley.
5. Remove the timing belt cover
6. Remove the timing belt tensioner pulley.
7. Remove the Timing Belt.
8. (If Replacing) Remove Idler Pulley.
Installation is reverse of removal. Keep a close eye on the timing marks on the cam sprockets to make sure you don't knock anything out of whack.

I would strongly recommend replacing the water pump while you are replacing the timing belt. (The water pump usually comes in the timing belt kit.) Otherwise you are going to have to do this all over again when your water pump goes out. Good Luck.

Nov 10, 2008 | 2004 Hyundai Tiburon

1 Answer

How to replace a serpentine belt on a ford taurus 2002


just replaced serpentine belt on my 2000 taurus with the push rod engine, first remove the plastic radiator recovery bottle.
next using a 15mm closed end wrench, remove the tension from the aerpentine belt. paying special attention on the routing of the belt prior to removing. Remove the old belt. Reverse this procedure to replace the belt.

Aug 11, 2008 | 2000 Ford Taurus

Not finding what you are looking for?
2000 Toyota ECHO Logo

318 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...