Question about 1991 Honda Accord

2 Answers

1991 honda accord

Can you tell me how to change a fuel pump and pull fuel tank discribe or send schematic thanks

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

There is no access from under the back seat on your particular model. You are going to have to drop the gas tank to get to it. The nice thing is that the Honda's come with a fuel drain which you will see when you get under there. Drain the fuel and then you will have to drop the tank and have somebod hold the tank while you get up into the fuel pump area. The problem is probably not your fuel pump though, they do not go bad very often on these cars. I thought mine was bad until I hooked up direct power from the battery and it worked. Try replacing the main relay under the driver's side dash it is underneath a silver box which controls your cruise control. The relay will say MAIN with 12V underneat it. It is brown and grey. Hope this helps

Posted on Aug 07, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 372 Answers

I suggest getting a repair manual. very detailed with diagrams. I could give u step by step but book will be easier...some of those cars allow access to the fuel pump from under the back seat..

Posted on Aug 06, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change feul pump 97 chevy lumina 3.1 l


You must remove the fuel tank which is underneath the trunk. Here's the procedure for removing the pump.

REMOVAL:

1. Before servicing the fuel pump the fuel system pressure must be relieved.
2. Disconnect the negative battery cable.
3. Raise the car on a hoist.
4. Remove the fuel tank.
5. Remove the fuel tank sending unit and pump assembly by turning the cam lock ring counterclockwise. Lift assembly from the fuel tank.
6. Pull the fuel pump up into the attaching hose while pulling outward away from the bottom support. Take care to prevent damage to the rubber insulator and strainer during removal. After the pump assembly is clear of the bottom support, pull the pump assembly out of the rubber connector for removal.

NOTE: Inspect the fuel pump attaching hose for any signs of deterioration. Also check the rubber sound insulator at the bottom of the pump. Replace damaged or deteriorated parts.

INSTALLATION:

1. Push the fuel pump assembly into the attaching hose.
2. Position the fuel tank sending unit and pump assembly into the fuel tank. Use a new "O" ring seal.

NOTE: Care should be taken not to fold over or twist the strainer when installing the sending unit as this will restrict the flow of fuel. Also, verify that the strainer does not block the full travel of the float arm.

3. Install cam lock over the assembly and lock by turning clockwise.
4. Reinstall fuel tank.

May 09, 2017 | Cars & Trucks

1 Answer

How to change fuel pump on a 98 Pontiac sunfire


disconnect the electrical connections and fuel lines and vent lines at the tank then disconnect the fuel filler hose from the tank. support the tank then undo the fuel tank straps then lower the tank down to the ground. be careful as the tank will be heavy depending on how much gas is in it. clean the area around the sending unit. there is a lock ring that holds the sending unit assembly in the tank that needs to be removed then you can pull out the unit. at the bottom of the sending unit is the fuel filter. follow the instructions that came with the new fuel pump.

Oct 10, 2014 | Cars & Trucks

1 Answer

How do I change the fuel pump in a 1998 S-10 chevy pickup?


The electric pump is attached to the fuel sending unit, located in the fuel tank.

9b87eff.jpg

Fig. 1: Exploded view of the fuel pump and related components used on TBI equipped models (click for zoom)



REMOVAL & INSTALLATION
  1. Properly relieve the fuel system pressure.
  2. Connect the negative battery cable.
Be sure to keep a Class B (dry chemical) fire extinguisher nearby.

CAUTION Due to the possibility of fire or explosion, never drain or store gasoline in an open container.
  1. Drain the fuel tank, then remove it from the vehicle. Refer to the procedure found later in this section for details.
  2. Using the GM fuel gauge sending unit retaining cam tool No. J-24187, J-36608 (or equivalent) or a brass drift and a hammer, remove the cam locking ring (fuel sending unit) by twisting counterclockwise. With the locking ring released, carefully lift the sending unit from the fuel tank.
  3. Remove the fuel pump from the fuel sending unit, by performing the following procedures:
    1. Pull the fuel pump up into the mounting tube, while pulling outward (away) from the bottom support.
When removing the fuel pump from the sending unit, be careful not to damage the rubber insulator and the strainer.
    1. When the pump assembly is clear of the bottom support, pull it out of the rubber connector.
To install:
  1. Inspect the fuel pump hose and bottom sound insulator for signs of deterioration, then replace, as necessary.
  2. Push the fuel pump onto the sending tube.
  3. Using a new sending unit-to-fuel tank O-ring, carefully lower the sending unit/fuel pump assembly into the fuel tank.
When installing the sending unit, be careful not to fold or twist the fuel strainer or it may restrict the fuel flow.
  1. Secure the sending unit by turning or driving the lockring clockwise and into position under the tabs.
  2. Install the fuel tank assembly to the vehicle.
  3. Connect the negative battery cable and check for proper pump operation.

Hope this helps (/remember to rate and comment this).

Sep 17, 2010 | 1998 Chevrolet S-10 Pickup

1 Answer

How to install fuel pump need to find diagram to install thank you


the service manual tells you what to do but not breakdown on illustrations
lower the fuel tank when emptied
disconnect all fuel lines and unplug electrical connectors
remove the retaining ring to fuel pump and sending unit
pull out the sending unit with pump
reverse this procedure to reinstall

Jun 05, 2010 | 2003 Pontiac Grand Am

2 Answers

How to remove fuel pump on 1988 gmc s 15 pickup


GM S10/S15/Sonoma Pick-Ups 1982-1993 Repair Manual Electric Fuel Pump - REMOVAL & INSTALLATION
  1. Properly relieve the fuel system pressure.
  2. Connect the negative battery cable.
Be sure to keep a Class B (dry chemical) fire extinguisher nearby.

CAUTION Due to the possibility of fire or explosion, never drain or store gasoline in an open container.
  1. Drain the fuel tank, then remove it from the vehicle. refer to the procedure found later in this section for details.
  2. Using the GM fuel gauge sending unit retaining cam tool No. J-24187, J-36608 (or equivalent) or a brass drift and a hammer, remove the cam locking ring (fuel sending unit) by twisting counterclockwise. With the locking ring released, carefully lift the sending unit from the fuel tank.
  3. Remove the fuel pump from the fuel sending unit, by performing the following procedures:
    1. Pull the fuel pump up into the mounting tube, while pulling outward (away) from the bottom support.
When removing the fuel pump from the sending unit, be careful not to damage the rubber insulator and the strainer.
  1. When the pump assembly is clear of the bottom support, pull it out of the rubber connector.
To install:
  1. Inspect the fuel pump hose and bottom sound insulator for signs of deterioration, then replace, as necessary.
  2. Push the fuel pump onto the sending tube.
  3. Using a new sending unit-to-fuel tank O-ring, carefully lower the sending unit/fuel pump assembly into the fuel tank.
When installing the sending unit, be careful not to fold or twist the fuel strainer or it may restrict the fuel flow.
  1. Secure the sending unit by turning or driving the lockring clockwise and into position under the tabs.
  2. Install the fuel tank assembly to the vehicle.
  3. Connect the negative battery cable and check for proper pump operation.

Good luck (remember rated this).

May 24, 2010 | 1988 GMC S-15

5 Answers

Where is fuel pump located in 1999 Oldsmobile Bravada?


The electric pump is attached to the fuel sending unit, located in the fuel tank.

bd0ab83.gif
  1. Properly relieve the fuel system pressure.
  2. Connect the negative battery cable.
  3. Drain the fuel tank, then remove it from the vehicle. Refer to the procedure found later in this section for details.

    Using the GM fuel gauge sending unit retaining cam tool No. J-24187, J-36608 (or equivalent) or a brass drift and a hammer, remove the cam locking ring (fuel sending unit) by twisting counterclockwise. With the locking ring released, carefully lift the sending unit from the fuel tank.

    Remove the fuel pump from the fuel sending unit, by performing the following procedures:
    1. Pull the fuel pump up into the mounting tube, while pulling outward (away) from the bottom support.



    When removing the fuel pump from the sending unit, be careful not to damage the rubber insulator and the strainer.
      1. When the pump assembly is clear of the bottom support, pull it out of the rubber connector.


    To install:
    1. Inspect the fuel pump hose and bottom sound insulator for signs of deterioration, then replace, as necessary.
    2. Push the fuel pump onto the sending tube.
    3. Using a new sending unit-to-fuel tank O-ring, carefully lower the sending unit/fuel pump assembly into the fuel tank.

    When installing the sending unit, be careful not to fold or twist the fuel strainer or it may restrict the fuel flow.
    1. Secure the sending unit by turning or driving the lockring clockwise and into position under the tabs.
    2. Install the fuel tank assembly to the vehicle.
    3. Connect the negative battery cable and check for proper pump operation.
NOTE: A special tool is usually available to remove or install the fuel pump locking cam

56ca713.jpg
A brass drift and a hammer can be used to loosen the fuel pump locking cam

3209ccb.jpg
Once the locking cam is released it can be removed to free the fuel pump

7013104.jpg
Thanks for using FixYa - a FixYa rating is appreciated for taking the time to answer your FREE question.

Mar 26, 2009 | 1999 Oldsmobile Bravada

1 Answer

1998 dodge stratus fuel pump


Hello
If you have done a in tank one before this will go easy
drop the tank
remove the fuel lines
remove the electronic connector.
remove the ring from the tank that holds the sending / fuel pump unit into the tank.
replace the pump on the sending unit,
reverse steps to install
RD

Jan 12, 2009 | 1998 Dodge Stratus

1 Answer

2003 oldsmobile alero fuel pump


relieve fuel pressure (pull fuel pump fuse run car until it quits,) siphon fuel from tank, drop tank, remove wires and hoses,fuel pump is in tank, to remove, use snap ring pliers to remove pump retaining ring, pull up on pump, be carefull not to damage screen or sending unit in tank when pulling out.

Oct 23, 2008 | 2003 Oldsmobile Alero

2 Answers

Discovery td5 hard to start when cold fuel pump now noisy


what you are discribing is a fuel restriction
could be a defective fuel filter. it wouldnt be the first one ive seen
later paul

Sep 24, 2008 | 2002 Land Rover Discovery Series II

Not finding what you are looking for?
1991 Honda Accord Logo

152 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

71525 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22059 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7029 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...