Question about Dodge Ram 2500

Open Question

I HAVE A BOSCH VP-14 FUEL PUMP AND NEED A asembly diagram it came off of a 92 dodge cummings thanks chris

Posted by on

6 Suggested Answers

  • 979 Answers

SOURCE: I need a diagram for 1998 chevy tahoe fuel pump

Do you want a diagram, or do you just want to replace the pump?

Posted on Dec 17, 2008

  • 42 Answers

SOURCE: 92 camry fuel filter location

look under the air filter box, bolted to the framerail

Posted on Dec 28, 2008

SOURCE: wiring and vacuum diagrams

wiring diagrams for a lot of vehicles (but not all!)
go to autozone . com
repair info (on the left)
vehicle repair guides (center panel)
put in your vehicle info
select chassis electrical
then wiring diagrams (on the right, bottom of the list)

You might be able to find vacuum diagrams also, but I'm not sure.

Posted on Feb 21, 2009

  • 1 Answer

SOURCE: need a diagram for routnig

it easy the rib side of the belt go rib pully and the flat side on the flat pully

Posted on Apr 19, 2009

  • 3 Answers

SOURCE: need help with the wiring diagram for my 92 Dakota, has not brake lights or blinkers

www.wiring-diagram.com
You can get any wiring diagram for any vehicle. It will cost about $12 and it's well worth it. It will give you the complete diagram bumper to bumper.

Posted on Apr 29, 2009

mechanicm639
  • 253 Answers

SOURCE: 1999 dodge ram 3500 cummings turbo diesel will not start.

Diesel engines fire on compression alone (usually 400psi).The Truck may have air trapped in the fuel system.When you perform any fuel system repair on a diesel it is going to take alot of cranking to get the air out. You can take the breather loose and shoot a VERY small amount of starter fluid in the intake and it should start. Do not use starting fluid much as it can damage the engine. Good Luck.

Posted on May 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i remove a fuel pump on ford transit mk 6 model


THE PUMP IS LOCATED IN THE FUEL TANK YOU WILL NEED FUEL LINE DISCONNECT TOOLS BEFORE YOU ATTEMPT THIS TASK AND BE MINDFUL OF THE FUEL TANK PRESSURE SENSOR IT IS EASY TO BRAKE AND HARD TO REPLACE COST ABOUT $70.00 (IF IT AIN'T BROKE DON"T FIX IT)

May 05, 2014 | 2009 Ford Transit Connect

1 Answer

Need instructions on how to replace water pump on 92 dodge ram 2500, 5.9 diesel turbo cummings


  1. Disconnect the negative battery cable.
  2. Drain the coolant.
  3. Use a 3 / 8 in. drive breaker bar to lift the belt tensioner and remove the belt.



0900c15280070771.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 12: Always install a new O-ring in the diesel water pump

  1. Remove the two water pump retaining bolts and remove the pump from the engine.
  2. Remove the O-ring from the pump groove.

To install:
  1. Clean the O-ring groove and install a new O-ring.
  2. Clean the pump mating surfaces and install the pump to the engine.
  3. Tighten the mounting bolts to 18 ft. lbs. (24 Nm). Fill the radiator with coolant.
  4. Install the drive belt.
  5. Connect the negative battery cable, run the vehicle until the thermostat opens, fill the radiator completely and check for leaks.
  6. Once the vehicle has cooled, recheck the coolant level.

Dec 24, 2010 | 2004 Dodge Ram 2500

1 Answer

92 dodge stealth rt tt, car drives fine for maybe a week , maybe a day maybe 5 mins , rpms drop to zero car shuts off right away , like turning the key, wont re start sometimes for hour , maybe 2 then...


there is a none problem at fuel pump housing we just had 92 with same problem it finally started blowing engine fuse but were the wiring goes thro the top of the fuel pump hanger assembly there are insulators and they come apart allowing the fuel pump current to dead short at hanger asembly you may want to investigate closer hope this helps we had his ecm sent out for rebuild also sounds the same

Aug 10, 2010 | 1992 Dodge Stealth

1 Answer

Changing fan belt in a 2006 dodge cummings


diagram should be under hood,, on top of radiator cover

Mar 13, 2010 | 2006 Dodge Ram 2500

1 Answer

I have a 2004 Doge Ram 3500 cumming run 5mile Dies and restart and repets about the same miles I tride pump test and its to spec


get fuel pressure gauge ASAP. replace lift pump with after market one (not in tank from dodge..junk)

Feb 03, 2010 | 2004 Dodge Ram 3500 Truck

1 Answer

I have a 1998.5 dodge 5.9 cummings diesel 24 valve factory stock, the fuel lift pump is not on engine or fuel lines, did dodge mount it in fuel tank?


It was located on the drivers side of engine close to fuel filter housing, but dodge has been selling and installing kits that change it to the in tank style for quite some time, so if not on block it must have been converted at some time.

Jan 04, 2010 | 1999 Dodge Ram 2500 4WD

1 Answer

92 Dodge Dynasty wont start no spark no fuel


If there is no spark, then there is no signal to crankshaft position sensor. If no power to fuel pump, check relay and power to it.

If you are not getting power to either of them.Then igniitn module or ECM is faulty.

Oct 15, 2009 | Dodge Dynasty Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

235 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...