Question about 2005 Ford Futura

1 Answer

I need to change oil pan on my 1997 ford contour

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Http://www.2carpros.com/how_to/how_to_change_oil_filter.htm

Posted on Dec 20, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Could you show me or tell mewhere the transmission filter is located on a 1997 ford contour 2.5ltr. v-6?


You have to drop the transmission pan with gasket to get to the transmission filter. About 5 quarts or so of transmission fluid will come out when you drop the pan. You have to buy a new transmission gasket. Do not reuse the old gasket.

Jun 10, 2014 | 1997 Ford Contour

1 Answer

Oil coming from bottom of 1996 ford contour. No leak from the motor


If you have recently had your oil changed,the oil filter may be loose or cross threaded.Also if you have had an oil change recently it could just be spilled oil. Make sure your oil filler cap is on tight and the dipstick is on tight. While you are at it check to see how much oil you have actually lost.If it`s not coming from the engine,i would inspect the oil pan gasket and the oil pan itself may have a hole in it.

Nov 12, 2012 | 1996 Ford Contour

1 Answer

1997 ford contour has oil shown on dipstick at correct spot on dipstick, but oil light is on?


i know a light on your dash can drive you crazy, but as long as you are sure the oil is showing on the correct place on the dipstick you should have no problem

Jan 10, 2011 | 1997 Ford Contour

1 Answer

Drain plug 1997 ford contour


ON A 2 LITER ITS LOCATED AT THE BACK OF THE OIL PAN(TOWARDS BACK OF CAR), ON A 2.5 LITER ITS LOCATED SAME AREA

Mar 16, 2010 | 1997 Ford Contour

1 Answer

Trying to change transmission filter out on a 1997 ford probe v4.


159 7A100 Main Control 160 7H249 Oil Filter Recirculating Regulator Exhaust Seal 161 7A098 Oil Filter and Seal Assy

ff4e84a.gif

Mar 10, 2010 | 1997 Ford Contour

1 Answer

Son has a 1997 contour with 2.0l overheated


hard to get to and difficult job...are you sure you dont have cracked head? is there water in the oil....does the oil look milky? look in the radiator is there oil residue in the coolant........

Nov 08, 2009 | 1997 Ford Contour

2 Answers

Timing belt marks 1997 ford contour 2.0 eng.


Ford Contour / Mystique / Cougar 1995-1999 Repair Guide

c398e23.jpg


More details in Autozone.com.

Good luck (rated this)

Sep 02, 2009 | 1997 Ford Contour

2 Answers

How to change the oil pan on my 2000 Ford Contour 4cyl.......I was told at the oil change place that it was all rusted out and leaking and needs to be replaced....How big a job is this???? Can I do this,...


It shouldn't be that big of a deal. If the oil pan is the only part that has oil on it, it is most likely an oil pan gasket or rtv sealant that needs to be replaced. If you have actual holes in the pan then your problem is probably bigger. Depending on how bad the rust is, getting those fasenters out might present a problem so I would try turning a couple before draining all the oil. If the bolts turn then drain the oil from the plug as if you were doing an oil change. There are twelve of these bolts and there is a proper untightening and tightening sequence which is difficult to explain without a diagram but try and work in a spiral pattern from the center. Once it is off make sure you scrape all rtv off and any oil residue otherwise it will leak again. Re-apply rtv or whatever ford recommends and when it is ready, put it back trying to tighten the bolts from the center working your way out in a criss cross spiral pattern. Hope all goes well

May 12, 2009 | 2000 Ford Contour

1 Answer

97 ford contour gl, info on transmission pan filter installation?


trans filter can only be replaced by taking the trans apart. absolutely not worth it.

Apr 10, 2009 | 1997 Ford Contour

1 Answer

How to remove the oil pan on a 99 ford contour 2.5


This is quite a chore, you have to lift the engine to do it:

From AutoZone...

Disconnect the negative battery cable.

Remove the water pump pulley shield.

Install engine support device to the engine lifting eyes and support the engine.

Raise and safely support the vehicle.


Remove the exhaust crossover and the exhaust retaining bracket located on the right side of the oil pan.

Remove the exhaust heat shield retaining nuts and the exhaust heat shields from the left side of the oil pan.


Feb 23, 2009 | 1999 Ford Contour

Not finding what you are looking for?
2005 Ford Futura Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...