Question about 2000 Chevrolet Silverado 1500

1 Answer

I have a 2000 chevy truck with a 5.3L motor i wash the motor off and it want stay cranked

Posted by on

1 Answer

Ooo

Posted on Jul 30, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 chevy monte carlo when trying to crank it won't stay. the alternator has been checked, the starter, and battery, please help.


Wont stay?? cranking or running? Assuming it cranks but wont stay running I would be suspect of a Crankshaft Position Sensor

Feb 13, 2014 | Chevrolet Monte Carlo Cars & Trucks

1 Answer

Throttle body problems


Need more data. Please provide:

Vehicle Year (2000)
Vehicle Make (Chevy)
Vehicle Model (Caprice)
Vehicle Engine Size (5.0L)
at a minimum.
Also, does the vehicle seem to crank faster than normal (like there is no resistance in the motor)?

With that info I can better assess your problem

Nov 02, 2013 | Cars & Trucks

1 Answer

2000 Chevy S-10 P/U Flex Fuel 4 cyl


Are you saying the engine will not crank, or not start ?
Will it crank in neutral ?

Jul 05, 2013 | Chevrolet Cars & Trucks

1 Answer

I have a 2000 Chevy Impala and my car only stay crank if my foot is on the gas, when I release , it shuts off. It's not the mass air flow sensor or fuel pump what can it be??


Inspect, clean or replace the Idle Air control valve...about $35 for the part...also how is the air filter? A clogged catalytic converter can cause this too? ( A free check at quality muffler shops. Hope this helps.

Mar 16, 2012 | 2000 Chevrolet Impala

1 Answer

WINDSHIELD MOTOR REPLACEMENT FOR MY 2000 CHEVY C3500 HD


REMOVAL PROCEDURE
  1. Remove the wiper arms.
  2. Remove the air inlet grille panel.
  3. Disconnect the electrical connector from the motor. IMPORTANT: Do not remove the crank arm.
  4. Loosen the nuts attaching the drive link brackets to the crank arm.
  5. Remove the brackets from the wiper motor crank arm.
  6. Remove the three bolts and the wiper motor from the vehicle.
INSTALLATION PROCEDURE
  1. Install the wiper motor on the vehicle. NOTE: Refer to Fastener Notice in Service Precautions.
  2. Install the three bolts. Tighten Tighten the three bolts to 7 N.m (62 lb in) .
  3. Install the drive link brackets to the wiper motor crank arm with the right side linkage closest to the wiper motor. Tighten Tighten the link nuts to 5 N.m (44 lb in) .
  4. Connect the electrical connector to the wiper motor.
  5. Install the air inlet grille panel.
  6. Install the wiper arms.

May 10, 2010 | 2000 Chevrolet 3500

1 Answer

2000 chevy s10 starting problem


there is a solinoid that enguages the starter it is stuck tap the round cylinder that is atached to the top of the starter it should disenguage the solinoid if not try to hit it harder. dont beat it up though. it also may need a new starter.

Jul 17, 2009 | 2000 Chevrolet S-10

1 Answer

1996 chevy Tahoe put new motor in and gauges are off


is the distributer in correctly those only go in way only and there is no adjusting timing on those motors assuming it is the vortec motor

Apr 28, 2009 | 1996 Chevrolet Tahoe

1 Answer

Winshield wipers stay stright when you turn them off 2002 chevy impala


You need to replace the wiper crank arm that is bolted to the wiper motor. Then you need to bend the tab back up that got bent on the wiper motor bracket that the old crank arm bent. The crank arm has to hit this metal tab so the wipers will park down below the window istead of up.

Mar 06, 2009 | 2002 Chevrolet Impala

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61292 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...