Question about 2007 Toyota Camry

4 Answers

Keyless entry hi i lost my original key that comes with the keyless lock / unlock buttons any clues please

Posted by on

  • Anonymous Jul 31, 2008

    have Toyota camry , year 2007
    i lost my original key same you, that comes with the keyless lock / unlock buttons any clues
    please you to have solutio any time send to e-mail

  • Anonymous Mar 02, 2009

    my daughtet lost her keyless /remote that will activate the alarm . she has a spare key but she says it will set the alarm off and the car will not start. help

×

4 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

You can still start your veichle by removing the (ICGT) fuse from the fuse box.
the car will start now without the remote.

Posted on Feb 13, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 60 Answers

Hi. These cars usually come with three (3) keys: Two (2) master keys and one (1) Valet key, and a tag with the five digit key code they give you, for the car key replacement program at the dealership. With this code, they can access the database and with the verified information from the owner, you will get a key cut for your car at any toyota dealership.

Posted on Aug 22, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Dear
I have Toyota camry , year 2007
i lost my original key same you, that comes with the keyless lock / unlock buttons any clues
please you to have solutio any time send to e-mail
E-mail : hamelgc@yahoo.fr

Posted on Jul 31, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 359 Answers

Locksmith or dealer

Posted on Jul 29, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you reset the alarm system on a 98 olds silhouette after it triggers without the remote entry


Theft Deterrent Arm/Disarm Modes
Important: Although mode 2 provides increased security, the content theft deterrent system disarms only by pressing unlock on the keyless entry transmitter. This can pose a problem if the keyless entry transmitter is damaged, lost, or inoperative for any reason while you attempt to disarm the content theft deterrent system.
Mode 1: The system arms when you lock the doors with the keyless entry transmitter. The system disarms when you unlock the left front, right front, or liftgate door with the key or the keyless entry transmitter. The system does not arm when you lock the doors with a power door lock switch.

Mode 2: The system arms when you lock the doors with the keyless entry transmitter. The system disarms when you unlock the doors with the keyless entry transmitter. The system does not disarm when you unlock the doors with the key.

Mode 3: The system arms when you lock the doors using a power door lock switch or the keyless entry transmitter. The system disarms when you unlock the left front, right front, or liftgate door with the key or the keyless entry transmitter.
Changing the Feature Customization Modes
  1. Turn off the IP dimmer switch.
  2. Turn the ignition switch to the LOCK position.
  3. Remove the BCM PRGRM fuse.
  4. Turn the ignition switch to the ACC position. The BCM flashes the fasten belts indicator and sounds the chime 4 times, which indicates that BCM type 4 is installed on the vehicle. At this point, the BCM has entered the feature customization mode.
  5. In order to change the theft deterrent/shock sensor mode, turn the headlamp switch from OFF to PARK and back to OFF.
  6. The BCM flashes the fasten belts indicator and sounds the chime a number of times equivalent to the theft deterrent/shock sensor mode. A transition past mode 4 repeats the sequence starting with mode 1.
  7. Complete the following steps in order to change the theft deterrent arm/disarm mode:
6.1.
Insert the key in the left front, right front, or liftgate door lock cylinder.


6.2.
Rotate the key from the center to the unlock position.


6.3.
Press the horn button on the remote keyless entry transmitter.


6.4.
Count the number of chimes that you hear. The number of chimes tells you which mode you have set.


6.5.
Press the horn button again in order to change the mode. Continue to press the button until you hear the number of chimes that indicates the mode that you want.


6.6.
Turn the key back to the center position and remove the key from the door key cylinder.

In order to exit and save the current feature customization modes use the following procedure:

  1. Turn the ignition switch to the LOCK position.
  2. Reinstall the BCM PRGRM fuse.
If you are unable to change locking modes Theft Deterrent System Feature Customization Inoperative

Aug 25, 2015 | Cars & Trucks

2 Answers

I changed my batteries in my keyless remote


  • Jeep 1990 and later Remote keyless entry programing
  • Put the key in the ignition with all doors and trunk closed
  • Open the driver's door on the automobile and leave the door open.
  • 4 Move the switch on the door to the lock position while the door is open.
  • 5 Switch the key in the ignition two clicks to the right to the "On" position. do not start
  • 6 Press the lock button on your keyless remote for your Jeep and hold the button for 5 seconds. Release the button and remove the key from the ignition to complete the programming.


  • Read more : http://www.ehow.com/how_5019251_program-keyless-entry-jeep.html

    Jan 20, 2015 | 2002 Jeep Liberty

    1 Answer

    My mom lost her keyless entry remote. bought another online. i looked in the manuel and was unsuccessful in programming the new one. what steps must i take.


    1. 1 Press the lock button on your Chrysler remote five consecutive times at brief two second intervals.
    2. 2 Place your key in the car's ignition and turn it to the right two clicks to the "Run" position on all Chrysler cars.
    3. 3 Hold the unlock button. Then press and hold the panic button simultaneously. Release both buttons at the same time and you will hear a small beep to indicate that the programming is in effect.
    4. 4 Press and release both the lock and unlock buttons at the same time.
    5. 5 Turn the key to the off position and remove it from the ignition. Test your remote to see if the programming was successful.

    Read more: How to Program a Chrysler Keyless Entry Remote ' eHow.com http://www.ehow.com/how_5014707_program-chrysler-keyless-entry-remote.html#ixzz1ANbOsavi

    Jan 07, 2011 | 1998 Chrysler Cirrus

    1 Answer

    Hi. I lost the key to my 2009 accord xl. I picked up a replacement today and was given "instructions" as to how to make the necessary steps to get the car started - just to get the car up to the...


  • Have a seat in your Honda and close the doors, but make sure they are unlocked.

  • 2

    Turn your ignition key to the "On" position, labeled by two lines (II). Press the "Unlock" button on your keyless remote. Turn your ignition key to the "Off" position.

  • 3

    Repeat the procedure three times, and then turn the ignition key to "On." Immediately press the "Lock" button on your keyless entry. Listen for the doors to lock, and then unlock to signal that you are in programming mode.

  • 4

    Press the "Lock" button on the keyless remote, and then turn the ignition to the "Off" position to confirm.



  • Read more: How to Program a Honda Keyless Entry ' eHow.com http://www.ehow.com/how_5523557_program-honda-keyless-entry.html#ixzz1A7h1nyC1

    Jan 05, 2011 | Honda Accord Cars & Trucks

    1 Answer

    I have a 96 ford conversion van with a 600 plus addon keyless system and need to program new keyless remots , need to know how to get system in program mode.


    Hi.

    To program ( or reprogram ) a keyless entry remote transmitter into the remote keyless entry module, perform the following steps:

    1. Turn the key to ON or ACC and short the two terminals of the program connector, a two-pin connector located below the driver's side of the instrument panel at the base of the steering column. All doors should lock and then unlock.
    2. Press any button on each keyless entry remote transmitter in turn. All doors should lock and then unlock. If the door locks do not respond, press the button again (up to three times maximum with the same keyless entry remote transmitter). If the door locks still fail to respond, go to Pinpoint Test A.
    3. Repeat Step 2 to program additional keyless entry remote transmitters into the remote keyless entry module (up to four keyless entry remote transmitters maximum).
    4. Turn key off.
    5. Remove the short from the program connector. All doors should lock and then unlock.
    6. Verify that the keyless entry remote transmitters have been successfully programmed by pressing the LOCK or UNLOCK button on each one, and observing that the system responds by locking and/or unlocking the doors.


    I hope this helps you.

    Thanks!

    Nov 28, 2010 | 1996 Ford Econoline

    1 Answer

    Keyless entry 2005 grand am i put new ignition on car, 2005 grand am it came 2005 grand am that i own that was wrecked my car that i want to put it on did have remotes when i bought it they were lost, igot...


    To program the transmitters, perform the following procedure while seated in the vehicle driver's seat:

    Close all the vehicle doors.
    Remove the ignition key from the ignition lock cylinder.
    Press and hold unlock on the door lock switch.
    Important: To successfully enter the keyless entry programming/diagnostic mode, steps 4 through 6 must be completed within 25 seconds of pressing the door unlock switch.

    While holding the door lock switch in the unlock position, insert and remove the ignition key twice. Do not rotate the ignition lock cylinder.
    Insert the ignition key a third time leaving the key in the ignition lock cylinder. The ignition must remain in the LOCK position for the rest of the procedure.
    Release the door lock switch. The chime will sound three chimes to signal that transmitter programming/diagnostic mode is active.
    Press and hold the lock and unlock buttons at the same time on the keyless entry transmitter for approximately 4 seconds. The chime will sound two times to signal that the transmitter has been programmed successfully.
    To exit the transmitter programming/diagnostic mode perform either of the following:
    • Turn the ignition switch to the RUN position.

    • Remove the ignition key from the ignition switch

    Oct 21, 2009 | 2005 Pontiac Grand Am

    1 Answer

    Keypad door lock does not work..?


    it's in owner manual. But, first you have to enter your original code and it must work. then you press the 1 button and then enter a new 5 digit code, then press the 1 button again.

    Keyless Entry Keypad To unlock the driver front door (20124) , and disarm the anti-theft alarm control (19A366) , (if equipped):
    • Enter the permanent factory code.
    • Enter the owner's alternate code.
    To unlock the passenger door(s), press the 3/4 button within five seconds of unlocking the driver door or luggage compartment. To unlock the luggage compartment door (40110), press the 5/6 button within five seconds of unlocking driver or passenger door(s). To turn on the courtesy lamps and light all illuminated components, lift either front door handle (22404) or press any button on the keyless entry keypad (14A626) . To lock all doors, press the 7/8 and 9/0 buttons at the same time with all doors closed. (It is not necessary to enter the key code first.) This will turn off courtesy lamps and arm anti-theft alarm control (if equipped). To program an alternate code:
    1. Enter the five digit permanent entry code into keyless entry keypad .
    1. Within five seconds of pressing last button of permanent code, press the 1/2 button within five seconds of pressing the last button of the permanent code.
    1. Enter any alternate five digit code within five seconds of pressing 1/2 button.
      • Enter a sixth digit as follows to indicate operator's memory seat setting to be set by alternate code:
        • 9/0 — no memory recall
        • 1/2 — memory seat position 1
        • 3/4 — memory seat position 2
        • 5/6 — memory seat position 3
      • After successful programming, the doors will signal by locking and then unlocking.
    ---------------------------------------------
    • Keyless Entry Keypad Does Not Work Properly
    • Circuit.
    • Keyless entry keypad.
    • Electronic door lock control processor.

  • Open Fuses:
    • Town Car and Crown Victoria/Grand Marquis
    • Power Distribution Box (under hood)- K, 40A (Maxi)
    • Instrument Panel Fuse Panel - 17 (10A), 10 (20A), 8 (15A), 5 (15A) and 4 (10A)
  • Loose Connectors
  • Corroded Connectors
  • Oct 04, 2009 | 1995 Lincoln Town Car

    2 Answers

    Keyless entry remote quit working. Just purchased new battery. Now Spare remote does not work either.


    Transmitter Programming Notes Transmitter Programming

    1. Start with the ignition OFF, hold down the power unlock button on the door panel. Turn ignition key ON, OFF, ON, OFF. Release power unlock button on the door panel. The locks will cycle once.
    2. Hold down the keyless entry transmitter LOCK and UNLOCK buttons for 15 seconds . The locks will again cycle once.
    3. Repeat step #2 for each additional keyless entry transmitter.
    4. Turn the ignition on to exit the keyless entry transmitter programming mode. Programming is now complete

    Jun 17, 2009 | 2000 GMC Sierra

    1 Answer

    Key Pad Entry does not work


    does the key pad light when you press a button at night? If yes, the fuse is ok.
    Do you have the plastic card with the permanent code in your owner manual packet? If yes, tryit.
    report back.

    Keyless Entry The keyless entry keypad is hardwired to the GEM. The GEM interprets the inputs from the keyless entry keypad and then controls the associated operation. The keyless entry keypad will be illuminated for five seconds when any button is pressed. Additionally, it will request the illuminated entry feature to turn the courtesy lamps on. If a lock all doors code is entered, the illumination will turn off, as well as request the illuminated entry feature to turn off the courtesy lamps. When pressed, the keyless entry keypad supplies the ground signal to the GEM or the GEM receives a signal from the keyless entry remote transmitter. Then the GEM outputs a ground signal to the appropriate lock or unlock relay which supplies the power to the actuator to lock or unlocks all doors, including the luggage compartment. The keyless entry remote transmitter also unlocks the liftgate or activates the panic alarm by sending a signal to the GEM.
    --------------------------------------------------------------- Visual Inspection Chart Mechanical Electrical
    • Keyless entry keypad
    • Keyless entry remote transmitter
    • Central junction box (CJB) Fuse F222 (20A)
    • Circuitry
    • Generic electronic module (GEM)
    ------------------------------------------------------------------------
    • No communication with generic electronic module (GEM)
    • Generic electronic module.
    • Circuitry.
    • REFER to Section 419-10 .
    ------------------------------------------------------------------------------------

    Mar 08, 2009 | 2003 Ford Taurus

    2 Answers

    Trunk won't open -1993 audi 90S


    if you can drop back seats you can get in and manually flick the lever when it is open you will have to go to dealer to see if you can get a key to match or you might get 1 in a junkyard. if this helps please rate me

    Nov 21, 2008 | 1993 Audi 90

    Not finding what you are looking for?
    2007 Toyota Camry Logo

    519 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Toyota Experts

    yadayada
    yadayada

    Level 3 Expert

    60541 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21927 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6811 Answers

    Are you a Toyota Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...